Re: [j-nsp] MX480 SCB firmware issue
It could also be a hardware issue in either the referenced scb0 or back connector. Have you tried the following: Re-seat the scb in its slot, and then check for bent pins at this time (you can use a flashlight) Swap the scb0 with a spare (Or borrow one from another slot 1, 2) Cheers, Masood On Tue, Dec 30, 2014 at 5:29 AM, Dave Peters - Terabit Systems d...@terabitsystems.com wrote: Thanks a lot for the information. It's definitely an SCBE (not a 2), but I tried upgrading to a 13 version just in case. Same FPGA revision error, and same firmware dead end. I appreciate the help. If anyone else has any pointers, let me know. -Original Message- From: juniper-nsp [mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of Tobias Heister Sent: Tuesday, December 23, 2014 2:54 PM To: juniper-nsp@puck.nether.net Subject: Re: [j-nsp] MX480 SCB firmware issue Hi, Am 23.12.2014 um 23:23 schrieb Dave Peters - Terabit Systems: 1 alarm currently active Alarm time Class Description 2014-12-23 21:50:13 UTC Major CB 0 FPGA Revision unsupported In looking over the Juniper documentation, there's a request system firmware command to update the SCB, but unfortunately, I'm not seeing that option (meaning request system ? doesn't reveal firmware as a possibility). I'm also not seeing any specific BIOS/firmware files in the download section of the Juniper MX Series portion of the Juniper website. It is a hidden command, so you have to manually complete it. After the firmware it starts to auto complete: request system firmware ? Possible completions: downgrade upgrade request system firmware upgrade ? Possible completions: fpc Upgrade FPC ROM monitor pic Upgrade PIC firmware vcpu Upgrade VCPU ROM monitor The output above is from an MX240 with SCB. I have never seen that error showing up but from what i have seen on similar situations the firmware should be embedded in junos and the firmware upgrade should just work without additional files. But SCB seems not to be a valid upgrade target on MX: request system firmware upgrade scb error: command is not valid on the mx480 tested on MX480 with SCBE Would you by any chance have bought SCBE2 (they would probably not been available in used condition) instead of SCB. Just asking because SCBE2 is supported starting from 13.something and does not work in 12.3 -- Kind Regards Tobias Heister ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
Re: [j-nsp] MX480 SCB firmware issue
Thanks a lot for the information. It's definitely an SCBE (not a 2), but I tried upgrading to a 13 version just in case. Same FPGA revision error, and same firmware dead end. I appreciate the help. If anyone else has any pointers, let me know. -Original Message- From: juniper-nsp [mailto:juniper-nsp-boun...@puck.nether.net] On Behalf Of Tobias Heister Sent: Tuesday, December 23, 2014 2:54 PM To: juniper-nsp@puck.nether.net Subject: Re: [j-nsp] MX480 SCB firmware issue Hi, Am 23.12.2014 um 23:23 schrieb Dave Peters - Terabit Systems: 1 alarm currently active Alarm time Class Description 2014-12-23 21:50:13 UTC Major CB 0 FPGA Revision unsupported In looking over the Juniper documentation, there's a request system firmware command to update the SCB, but unfortunately, I'm not seeing that option (meaning request system ? doesn't reveal firmware as a possibility). I'm also not seeing any specific BIOS/firmware files in the download section of the Juniper MX Series portion of the Juniper website. It is a hidden command, so you have to manually complete it. After the firmware it starts to auto complete: request system firmware ? Possible completions: downgrade upgrade request system firmware upgrade ? Possible completions: fpc Upgrade FPC ROM monitor pic Upgrade PIC firmware vcpu Upgrade VCPU ROM monitor The output above is from an MX240 with SCB. I have never seen that error showing up but from what i have seen on similar situations the firmware should be embedded in junos and the firmware upgrade should just work without additional files. But SCB seems not to be a valid upgrade target on MX: request system firmware upgrade scb error: command is not valid on the mx480 tested on MX480 with SCBE Would you by any chance have bought SCBE2 (they would probably not been available in used condition) instead of SCB. Just asking because SCBE2 is supported starting from 13.something and does not work in 12.3 -- Kind Regards Tobias Heister ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
[j-nsp] MX480 SCB firmware issue
Hi all-- Pardon my stupidity, but I'm getting the following error on a new (purchased used) SCB for an MX480 running the recommended software release (12.3R6.6): 1 alarm currently active Alarm time Class Description 2014-12-23 21:50:13 UTC Major CB 0 FPGA Revision unsupported In looking over the Juniper documentation, there's a request system firmware command to update the SCB, but unfortunately, I'm not seeing that option (meaning request system ? doesn't reveal firmware as a possibility). I'm also not seeing any specific BIOS/firmware files in the download section of the Juniper MX Series portion of the Juniper website. Can anyone take pity on me and give me some pointers on how to update the firmware and clear that error? As always, much appreciated. --Dave Peters ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
Re: [j-nsp] MX480 SCB firmware issue
Hi, Am 23.12.2014 um 23:23 schrieb Dave Peters - Terabit Systems: 1 alarm currently active Alarm time Class Description 2014-12-23 21:50:13 UTC Major CB 0 FPGA Revision unsupported In looking over the Juniper documentation, there's a request system firmware command to update the SCB, but unfortunately, I'm not seeing that option (meaning request system ? doesn't reveal firmware as a possibility). I'm also not seeing any specific BIOS/firmware files in the download section of the Juniper MX Series portion of the Juniper website. It is a hidden command, so you have to manually complete it. After the firmware it starts to auto complete: request system firmware ? Possible completions: downgrade upgrade request system firmware upgrade ? Possible completions: fpc Upgrade FPC ROM monitor pic Upgrade PIC firmware vcpu Upgrade VCPU ROM monitor The output above is from an MX240 with SCB. I have never seen that error showing up but from what i have seen on similar situations the firmware should be embedded in junos and the firmware upgrade should just work without additional files. But SCB seems not to be a valid upgrade target on MX: request system firmware upgrade scb error: command is not valid on the mx480 tested on MX480 with SCBE Would you by any chance have bought SCBE2 (they would probably not been available in used condition) instead of SCB. Just asking because SCBE2 is supported starting from 13.something and does not work in 12.3 -- Kind Regards Tobias Heister ___ juniper-nsp mailing list juniper-nsp@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp