KR> Engine Mount
Would anyone happen to know if engine mounts are available for jabiru engines? The Jabiru Web page, has engine mounts available, you add the measurements and they will make it. Phil Matheson -Original Message- ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Reductions PSRU
Does anyone have the plans / instructions for the Reductions belt drive Martin VW Engines Aust. Brisbane made my PSRU. Phil Matheson -Original Message- From: krnet-boun...@mylist.net [mailto:krnet-boun...@mylist.net] On Behalf Of Martin Pearce Sent: Thursday, 29 March 2012 8:19 AM To: kr...@mylist.net Subject: KR> Reductions PSRU ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> FW: Carring Passangers
PS I have sent it again. Tonight I was persuaded to carry an adult up for a ride in the KR. Between me and him there was 450 lbs --- Way to go Mark. I have only the standard KR2 and I carry myself ( 85kg) and I have had a 95Kg passenger. about 337 lbs total I need a fair bit of forward trim, but that's all, I do fly very smoothly and gental turns, and as you keep the speed up a little. One time I take off and my trim cable slipped and I had to fly with heaps of forward weight on the stick, I tried not to panic, I few to a close by air strip to save turning back, found the problem and went on our way. So in a KR2, the trim is very important with two adults on board. Phil Matheson Australia ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Tonights Flight( testing)
I have posted a number of replies and non have shown up on my inbox??? Phil Matheson. Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Carring Passangers
Tonight I was persuaded to carry an adult up for a ride in the KR. Between me and him there was 450 lbs --- Way to go Mark. I have only the standard KR2 and I carry myself ( 85kg) and I have had a 95Kg passenger. about 337 lbs total I need a fair bit of forward trim, but that's all, I do fly very smoothly and gental turns, and as you keep the speed up a little. One time I take off and my trim cable slipped and I had to fly with heaps of forward weight on the stick, I tried not to panic, I few to a close by air strip to save turning back, found the problem and went on our way. So in a KR2, the trim is very important with two adults on board. Phil Matheson Australia ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Floods
Yep, missed us by a mile again, but several others not so lucky... == Sorry to hear about you guys and the Tornados. Not much flying down under. I have had 10 inches of rain, and boy is it wet and flooded. Not as bad in my area as some, but WET. 75% of NSW is flood effected. Phil Matheson ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Canopy Frame
What type is best and should I rough the plexiglass up to get it to stick? -- I used west system, but I'm told any Epoxy will work. BUT since I did mine, a friend who makes canopies told the Polyester resin sticks much better to the plexi then epoxy, then you could use the epoxy to make the frame as it will stick VERY well to the Polyester. Or use polyester for all the frame. Get an off cut of plexi and use polyester on one and epoxy on the other and see which one comes off the easiest, you will be surprised, I was. Both work well. Phil Matheson Down under. ___ Search the KRnet Archives at http://mylist.net/private/krnet/ to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Wanted...O-200 engine mount
Craig, Gary I sent you a email of 0200 mount, from Paul Smith down under, thanks Paul Hope you get it OK. Phil Matheson. ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Grounded - wheel pant
How do you attach something to the end of the axle, that can be used for the attach point for the wheel pant? - Dan I have Matco, I drilled the axle, as per the KR instructions, made a "C" clip to replace the split pin through the bearing nut, I then made a nylon bush to fit on the end of the axle, to the wheel pant, bolted the unit to the axel. I glued a small bracket to the pant to lock wire the drilled bolt head. Phil Matheson
KR> Encapsulating
I've heard you can mix rubbing alcohol with it and the alcohol will evaporate out after you have spread it. You might test that on something first. -- I have been using what your guys over there call rubbing alcohol ( Mentholated Spirits) for years with great effect, in sealing timber, filling pin holes, etc. Phil Matheson. KR2 VH PKR ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Urgent- Need new Engine mount
I have a spare mount but I have found it is NOT as wide across the fire wall mounts as the damaged mount. This is a KR2 mount not sure is it is Harpi or what I need a mount with fire wall brackets with the 4 x AN3 bolts per mount (16 bolts) and 16 inches ( centre to centre) wide and 13 1/2 inches deep. (Some mounts are only 13inches wide) The engine is 8 1/4 inched off the fire wall. The engine bolts holes are 9 3/4 inches wide x 10 3/4 deep. Both are the same except the width of the mount brackets Phil Matheson >> ___ >> Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp >> to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net >> please see other KRnet info at http://www.krnet.org/info.html ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Engine Failure on Take OFF.
Well, it can happen to you. Last night 1730 at 500 ft Engine stopped dead. Lack of landing spots. Had to make 150' turn to safe ground. Check, tanks pumps NO start, but engine wind milling. A bit hot and ran out of field, had to lift over fence, then channel, stall, O S*#T - ground. Bugger. Walked away. KR home in my workshop. Damage, Prop, nose wheel collapse, L main collapse. Under inner wing whole from wheel. But main leg undamaged, the main bolts Sheared OFF, as did the nose wheel to fire wall bolts. NO cowl damage only paint. Engine mount bent. FOUND the cause this morning, the coil lead came out of the distributor Cap. No wonder it would not start. Did I seem Mark Jones make a cover or his dist. cap, Should listen to Mark. Impact point Google Earth 145 32.527 E 35 39.681S only 400m from my home. Phil Matheson VH PKR. KR2. ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> first KR arrived at the Gathering
Enjoy all. Phil Matheson -Original Message- From: Larry&Sallie Flesner Sent: Monday, 12 September 2011 5:50 To: KRnet Subject: KR> first KR arrived at the Gathering The first KR has arrived at Mt.Vernon for the Gathering. :-) I flew my KR in to be hangared at Mt.Vernon for the Gathering so I can drive my truck load of items to Mt.Vernon on Wednesday and start to get things set up. Everyone at Mt.Vernon is pumped for our arrival. Several nice additions since 2009 are an outdoor patio at the restaurant and a new 11,800 square foot hangar with two full baths for the campers. Chris is wrapping up the national light sport expo today and then he starts getting ready for us next weekend. YE H Larry Flesner ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> East Coast
Off topic. Just a quick good luck to all you guys in the path of the Hurricane . I wish you all the best of luck and please keep safe and lets know if you are all OK Thinking of you all. Phil Matheson. Australia. ___ Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Screws in spars
The RR sling seats as per plans, are held in place by wood screws in the top spar caps. Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> cam
Mark Also, the gear COULD get bent or out of round in the incident, but it WOULD NOT move on the shaft and show up as a misalignment??? Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> cam
Mark You could ask them if they have a 100% run out test policy on their finished shaft and gear? If not, they have no way of knowing it was correct when it left their shop? Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Grease on Wood
he spilled some oil and grease on the table and the right side of my project was still on the table -- Pat I would get some grease and fingerprint remover the Panel Shops ( Autoshops) use to rub off greasy prints and marks before they paint. This stuff works well, and I think it will do the job. Type in Wax & Grease Remover and do a search Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> KR-2 Wanted
To fly it with two people in it you have to modify and build the cabin wider ( Standard Kr is only 34") -- You are correct but you can do it. I have now flown a 2.5 leg with two large adults. I'm 5 ft 11, and 85 kgs, my father is 5ft 6 and 80 kgs. Full fuel. KR2. tri gear. Today I had a friend, he is 95kgs and it flew well., but remember I only have wing tanks, type 4 with belt drive, 60x 60 x 3 blade ground adjustable prop. 100 hp. So I have a good forward W&B. It can be done!!! Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Flying milkstools and idiots
I have never taken offence to the nose vs. tail wheel before but your tone is absolutely arrogant I do take offence to your comments. MY view is opposite to yours but I would never say what you did to anyone on this list Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Wanted- 0-200
Mark You could try one of these Diesel Engines http://www.dair.co.uk/ Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Dead Stick Landing
Sorry to hear about your forced landing, old friend. BUT very very glad to hear you and your best friend are safe and well. Great landing, well done, Please keep us up to date. Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> Lost wing in flight. Video clip- unbelievable-
Aviators - Holy smokes - this one is un-believable! Note how he gains 'control' and powers it to a landing. I'll bet he's religious now! http://www.chilloutzone.de/files/08102703.html Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com
KR> Is this a KR or what ??? on ebay
BRADLEY AEROSPACE AIRCRAFT ON SALE NOW Item number: 220298638293 http://cgi.ebay.com/ebaymotors/_Aircraft__BRADLEY-AEROSPACE-AIRCRAFT-ON-SALE-NOW_W0QQitemZ220298638293QQadiZ2829QQadnZAircraftQQcmdZViewItem?hash=item220298638293&_trksid=p4506.c0.m245&_trkparms=72%3A727%7C65%3A12%7C39%3A1%7C240%3A1308# Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html - Original Message - From: "bobby burington" To: "KRnet" Sent: Saturday, October 25, 2008 1:17 PM Subject: KR> 2180 cc. VW on ebay Hi all, For any one intrested there is a 2180 cc. VW Experimental Aircraft engine on ebay currently at $1,000.00 it is located in Deland, Fl, United States. the ebay URL is http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=230303220191&sspagename=ADME%3AB%3ASS%3AUS%3A1123&viewitem=Have a lookBobby BuringtonCalifornia KR Builder___Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jspto UNsubscribe from KRnet, send a message to KRnet-leave@mylist.netplease see other KRnet info at http://www.krnet.org/info.html
KR> Re: Corvair Engine Ebay- Australia
Item number: 320311822716 This seem a bit to many $$$. to me. Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR>I GOT it!
Welcome to the club. Phil Matheson SAAA Ch. 20 http://www.saaa20.org/ VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com --- Search the KRnet Archives at http://www.maddyhome.com/krsrch/index.jsp to UNsubscribe from KRnet, send a message to krnet-le...@mylist.net please see other KRnet info at http://www.krnet.org/info.html
KR> project status
Jeff wrote well all, I think I have a winner! I've attempted to make a turtle deck, this is now the 3 attempt. Check out how Scott Cable did his deck. My deck is very similar. Very light. http://krbuilder.org/ScottCable/index.html Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR>Engine run??
Well today I finished off the engine installation, and fired her up!! But I can not get the right bank to run. It only runs on the two left cylinders, Stromberg CD Carburettor. It has compression, Spark, timing is right, fuel in both carb float bowls, spark plug leads are on in the right order. No blocked intake manifolds, Suction at the carb inlet. I removed the right carb, pulled it down, could not find any defects, fuel of fuel.refitted it, still the same, I coughed the carb manually, not change. No fuel getting to cylinders. Both R exhaust , were cold to touch, and cylinder head temps cold. left side hot. ??? I'll keep playing when I get time again. Must be a major block in that R carb, but the main Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR>Engine run??
Colin. I can not find any info on the Stromberg. Where is the signal vacuum port?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Facet Fuel pump
Question. Does the facet fuel pump stop making a noise when the carbie bowls are full? My pump primes all the system, then quiets down, but never strops making a noise when the engine is NOT running??? I thought most Elect pumps stop pumping when fuel is not required? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Rebuilding Wings.
Robin My wings weight about 50 lbs with wing tanks Are the wings in such a poor state that they need rebuilding??, there have been somewhere a few bits on retro fitting wing tanks made from PVC and tubing?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Rebuilding Wings.
I send this hours and it still did not arrive, so you may get it twice - Robin My wings weight about 50 lbs with wing tanks Are the wings in such a poor state that they need rebuilding??, there have been somewhere a few bits on retro fitting wing tanks made from PVC and tubing?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re: KR Crash in Perth
I just saw what looks to be a BD5 crash in Perth on the early news. http://www.news.com.au/perthnow/story/0,21598,21763728-2761,00.html Will keep you posted Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Crash in perth
I have just found out it was Peter Gilbertson, from Perth, Mark would have meet him while there. There is a copy of an email from Perth Aussie KR member. Hi Phil Yes it was Peter. He had just taken off behind a Varieze and Gordon's BD5 but was not climbing. He appeared to decide to abort prior to reaching the end of the strip but landed very heavily with the gear up. Fire broke out a few seconds later. Luckily he came to rest just outside the Northam Aero Club clubhouse where many of the spectators were assembled so rescuers got to him within seconds, with fire extinguishers and strong arms. News reports indicates the burns are not serious but we don't know how bad the back injuries are yet. It could have been very much worse. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re: KR Crash in Perth
Photo from my web page of Peter's ( Aussie KR2 builder's) BD5 I took last year on a visit to Perth http://www.philskr2.50megs.com/images/peter_gilbertson_bd5-b_160_kt_++.jpg Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> flight in the desert
I did not get Lee's email either. I had to read the bottom of Darren's Go Figure????? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> thrust line
Phil. The Top of the longerons ???is the normal thrust line. I do remember a number of builder changing , including me. I lowering my thrust line about 1 1/2 inches below the longerons to allow the twin top mounted carbs to fit under the cowl line. But One of the Famous Mark's Brothers, sorry (Mark L and Mark J ) would be a much better adviser than I. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> vertical stabilizer plywood
Does anyone have any good close-up pictures of the vertical stabilizer section where the plywood is connected to fuselage member "N"? - Although not 100% clear I have one on my web page under the heading of controls?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> help with aileron linkage
Please look at : http://67.183.105.62/index.html Sorry, nothing open but a blank page?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> RE: help with aileron linkage (John)
John You could add ( said before) a longer bolt and spacer to the aileron pushrod, and lower the pivot point, or put an S shaped push rod so the REB is more centralized.?? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Personality changes.
is it normal to wake in the morning with KR thoughts pulsing through your mind... - Darren Sounds normal to me Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> acetone in epoxy mixes
Mentholated Sprits ( think you in US land call it Rubbing Alcohol)is really good for thinning and cleaning epoxy. Works very well when thinned to fill pin holes,being alcohol, some even mix with juice and drink it (BUT please not before a flight) But seriously, it works well. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> "S" Wing Construction
Don My Dan Diehl skins do not have the spar all the way, and have a foam ply extension. I know is not a 2S but they may do a similar thing ??? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re: Darren's web page
Darren You have done wonders with your web page. I think you will help a lot of new builders, and me when I start my next KR2SS. fuse. Well done, keep up the good work!! If you have not seen his web page, I can recommend it Another Aussie hard at work. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> wire and octane questions
Tetraethyl Lead is an anti knocking agent in fuel. Avgas still has lead!!! There are some additives around?? I Googled high octane additive, this and it will help Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> looking front nose gear leg ?
Dan Diehl will sell you the leg already bent and hardened. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Oiled Engine mount
The linseed oil is heated and pored in very hot, it then sticks better to the inside of the tube. so I'm told!! Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Seat attachment failure
This extremely dangerous situation with the seat bottom has existed for quite some time, judging by the elongated holes in the aluminum and other wear signs. During that time the plane has gone through a number of "annuals." It was only due to a great amount of luck and conservative flying (no high-speed passes with high-G pullouts, etc.) that the remaining two screws have not given ay. Thanks Mike. But that is why we do inspections. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re:Up Date
Well I can not believe how quiet the net is. I have been modifying my cowl to suit my engine air in takes, as my RG 2000 has a gear drive, the engine sits lower in the cowl and the cowl in lets are to high for a good direct flow, as well the inlets need to be low enough to have a ramp so the air can climb up hill to get to the barrels. This ramp allows a more direct and better cooling when the KR is in it's nose high climb configurations. So I cut out the old in lets last night and glassed over them, now I have to cut out new in lets and flare and glass them. As my engine has twin Stromberg Carbs with the oil dampened slides, the carb oil level has to checked before each flight or the carb will NOT get full throttle. I cut three inspection hatches in the top of the cowl, 2 for the carbs and 1 for the oil dip stick. Then ! hopefully the cowl can be painted, the barrel shrouds finished, and that will be it, all Finished, except for the C of A Photo Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re: Fuel per hose power
How many horse power is your engine when you work out the fuel burn Fuelburn 1 hp for 1 hr 0.284 litres of fuel per hr. Therefore 13 litres / hr divided .284= 45.77 HP Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> 35 for 35th
Would love to come, but would have a few fuel problems form Aust to US. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Glue Joints not holding
Brad I do not understand the mix ( uniform white paste) The T88 I have used was an amber colour, and mixed up to a honey consistency. As Mark L says let it soak in for a short before clamping. I'm sorry I can not be of more help, but I did not have any problems. Once the ply is over the joint, it will be a lot stronger, due to larger surface area. But still the wood should break, not the glue. It will be interesting to hear from the rest of the crew. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> First Engine Start
Well, I started my engine tonight, without prop. Just a short burst, but it only has one choke on the twin carbs, and was running rough, just needs a good run. Now I'm making the cooling ducts, This is the last thing I have to make. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> RE: Jandakot airport meeting
How come I did not receive Mark L's email from Perth?? or was there one ??? Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Engine start without prop
Thanks for all your concerns. My geared RG 2000 engine has a flywheel and gear reduction. I do not remember saying anything about over revving or flogging my engine, I did say I started it up. Vw Engines also ran it last week without a prop, just check they fixed all the oil leaks. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re: canopy bulkhead shape
Does anybody think I will be able to sort of square off the KR canopy -- stev. I have a Todd's canopy, and was doing to square off the back of my canopy, But like you was not sure at the time. But if I was to do it again, YES I would flatten the top rear and then glass in a rear frame. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Scarf question
Soany suggestions on how to fix this without ripping the skins off and reskinning? What would be wrong with just adding a frame to the location where the scarf join is?? But I have seen another flying KR that did not bother fixing the same mistake. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Oil Temp
My Type 4 VW has the oil temp sender in the sump, and I'm told the oil temp could reach 130c 266f. in the sump. But I'm also told the oil should not go above 100c 212f, Where are you guys locating your oil temp senders with the Type 4 VW's Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Re:Three views
Has anyone got a made up Tri- Gear KR2 three view to add to my flight Manual you can email me PLEASE! Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Roll over Pertection
Carrying a sharp pointed tool to break the Plexiglass in case of roll over should not be consider foolish. -- This is mandatory to my way of thinking. some where in easy reach, when you are up side down, and in confined space. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> FW: M.Aero: Ron Freiberger
To all Ron's friends on the net, and family, please accept my condolences. It's a sad day. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Wing tie downs
Has anyone put tie downs in their wings ?. --- My tie downs are from the Dan Diehl web page of instruction on his wing skins. Eye bolts through the spar out near the wing top end, or epoxy a block frame to spar in same place and drill this for eye bolts. Remove eye bolts when not needed and keep in tie down kit in plane. see Dan's web page. at the bottom of page under KR2 wing skins. Then click on the wing skin instructions. see step 4. http://www.diehlaero.com/ Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Roll over Pertection
This is the requirement for a roll over bar, as per regs " The structure must be designed to protect the occupant in a complete turnover, assuming, in the absence of a more rational analysis:-" (1) An upwards ultimate inertia force of 3g's ; and (2) A coefficient of friction of 0.5 at the ground. SO, KR2 of 1000 lbs weight X 3 g's = 3000 lbs, times 0.5 = 1500lbs. force hitting you bar. Then remember that you plane is then sliding backwards over the ground?? so the force is then trying to push the bar onto YOU. ( that's why I have two cables back to the tail bulk head). So, IS can your glass roll over protection strong enough??? Always ask someone qualified, who knows. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> KR Construction Update
Well guys and girls, I have all but finished my KR. I have just spent two week holidays in my workshop and my KR is all but, finished. I have done all those little jobs, like upholstery,calibrating fuel senders ,installing flightsel for my mobile phone usage via headset,The engine will be refitted next week, as I return to work tomorrow, The cowl has a few minor glassing jobs around the exhaust outlets then I can paint the cowl and wing gap seals, THAT will be it. Then sort out the C of A and YeeeHaaa. I had added two photo's to my web page, less the engine. I'm still in two minds as to the colour of trims to add to the fuselage. NOTE Please all of you, back up your hard drives, and photo's. I lost my hard drive yesterday and all of my building photo copies. (plus every thing else) Don't let it happen to you!!! I just added the latest photos to my web page. Home page and latest photo page. www.philskr2.50megs.com Phil Matheson SAAA Ch. 20, VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> KR Building Update
I sent this in hours ago but it did not appear so I'll sent it again. Well guys and girls, I have all but finished my KR2. I have just spent two weeks holiday in my workshop and my KR is all but, finished. I have done all those little jobs, like upholstery,calibrating fuel senders installing flightsel for my mobile phone usage via headset,The engine will be refitted next week, as I return to work tomorrow, The cowl has a few minor glassing jobs around the exhaust outlets then I can paint the cowl and wing gap seals, THAT will be it. Then sort out the C of A and YeeeHaaa. I had added two photo's to my web page, less the engine. I'm still in two minds as to the colour of trims to add to the fuselage. NOTE Please all of you, back up your hard drives, and photo's. I lost my hard drive yesterday and all of my building photo copies. (plus every thing else) Don't let it happen to you!!! I just added the latest photos to my web page. Home page and latest photo page. www.philskr2.50megs.com Phil Matheson SAAA Ch. 20, VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/ Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Termite
Is this a late April fools Joke?? Never seen a winged termite Lucky it was not an RV and get metal mites, they cause rust. Phil Matheson SAAA Ch. 20 VH-PKR Australia EMAIL: phillipmathe...@bigpond.com KR Web Page: www.philskr2.50megs.com http://www.vw-engines.com/
KR> Contemplation
The KR2(S) seems to offer a good combination of simplicity, economy and performance, and this might be a really good project to do with my 10 Y.O. son... -- Personally I think the idea of building with your son is fantastic. What a way of learning and spending quality time with him. BY the time it is finished he would be getting close to be able to fly it. My KR is just about finished with I had a son to share, On the other side my dad has been a great help to me, and assisted when I needed help. I took him flying in the 152 yesterday, and we landed at an ultralight flying in with a full size Kittyhawk up my rudder. A very good chose of aircraft to build. Good luck Phil Matheson VH-PKR mathes...@dodo.com.au 0358833588 Australia Web Page http://www.philskr2.50megs.com/ See VW Engines http://www.vw-engines.com/ www.homebuilt-aviation.com/
KR> moto-glider
Yes Garry Morgan in Australia had 27 foot wing span on his early KR. He doubled the thickness of the WAF only at the bolt hole then drill it out to next size bolt. as requested by is LAME search for Garry Morgan on Google Phil Matheson VH-PKR mathes...@dodo.com.au 0358833588 Australia Web Page http://www.philskr2.50megs.com/ See VW Engines http://www.vw-engines.com/ www.homebuilt-aviation.com/
KR> Fire Retardant Resin Additive
This is a copy of an email I sent to all Aussie KR guys, Hope you find it of interest. You will get this additive in the USA. Alumina Triydrate ( Google this for more info) This is a Powder that is mixed with Fiber Glass resin and stops the glass from burning when the flame is removed. You can mix and make a complete cowl or paint the inside to give some protection. Cost $10.00 per Kg, mix 25 :1 weight. Available from Ironbark Composites, Near Geelong Vic Call Dick Garrard. Iron Bark Composites 03 52648505 ph 0352648507 fax d...@ironbarkcomposites.com.au Will ship up to 3 kgs. regards Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/ / Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> 6063 aluminum/ Brackets
what will current builders use to make the brackets that we always used this stuff for? I never found any 4 inch angle. So I just got T6 in small sheets here in Australia. and just bent and made my own brackets. as per plans measurements ( available from a number of places in Aust. down to 1 foot x 1 foot, ) Piece of cake. Just make sure you bent it around a correct radius. ( I found a 1 inch by 1 inch hollow section had the perfect radius) Look in the Tony Bingelis books for help!! Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Poll - KRnet email list or new forum?
I had no problems getting into the forum, but once I started to find my way around, it seemed like a complete waste of time, it seem to take forever to switch from one section to another. I think the KRnet is by far better. my 2 cents worth. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Belt Drive PSRU
Up date My engine has been returned to VW Engines to have a problem fixed with the oil Cooler set up. (a damaged fitting in the block that needed some work.) Ron Slender has phoned to say that VW Engines will not be making anymore Helical Geared PSRU. ( Geared Drives) Instead, because of the cost of production and they are trying to stay competitive, They will be using a belt drives from now on. He offered me a great deal to change it over to belt drive while he has the engine. This is worth some thought, has it will save weight, less moving , and wearing parts, less noise, vibration and harmonics, as well as less service costs. Belts should last ??? 500 hours plus Comments for far have been positive. What do you guys in the know think?? So I need to make up my mind quickly. So I will be working to have the airframe finished when the engine returns in a few weeks. VW Engines have yet to update their web page to reflect this yet, as these things take time. Retail Cost of the Belt PSRU should be out soon if anyone is interested., But I would think they will only be available for the Type 4 rear drive.,but I will let you know soon. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Cold Weather Flying
Mark It is a really simple job to fit a heater. I used a Air box from A/Spruce, it is a kit not complete and only about $35. And of course a hot box around the exhaust Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> The Poor Man's Engine Pre-Heater
Sorry it's not Friday, But I have added a copy of an email below from a builder in Australia, who is now not going to build a KR because he says he can not contact R & R or they will not return is calls or faxes. Very disappointing!!!! Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/ Hi Phil, Thanks for adding me to the local KR list you have here in Australia but I won't be proceeding with building a KR plane. I sent Mrs Rand my money about 5 weeks ago and I have tried nearly every day for one whole month to get a few simple questions answered by her about buying kit components - but all to no avail I'm afraid. Her refusal to communicate in any way, shape or form, made me realise the futility I would face if I ever needed to actually try and order some components from RR, so I sent her a fax last week asking for my money to be refunded (though I haven't had a response to that request either). If I can't get a refund I will offer the plans up for sale as soon as the arrive. All the best to you and the other local builders. Regards Chris O'D
KR> Engine Pre-Heater/ R & R
Sorry all I forgot to change the subject line Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> The Poor Man's / Bailing out
Sorry I forgot to change the subject line -- I had the same problem, but after about 2 weeks, I was finally able to get ahold of a nice lady from RR. Perserverence is the key, I guess. -- - Original Message - From: "Phil Matheson" To: "Mark Jones" ; "KRnet" Sent: Sunday, February 04, 2007 5:00 PM Subject: Re: KR> The Poor Man's Engine Pre-Heater >
KR> Radio...Microair 720
Have a look at the Micoair 720. Fits in 2 1/2 inch hole. is fiddly but use but has a remote button you can place on your stick and it will scroll through the radio freq. you can add what freq. you wish. also has a priority emergency number http://www.microair.com.au/ Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Radio...Microair 720
I have one in my KR. I have used it only to test. A few guys ( older Guys) say it is difficult to use because the knobs are small and the squelch and volume knob are one. The first one is the volume and the one behind is the squelch. There is a page somewhere on their web that had the full operation instruction you can down load for a look Found it. Have a read http://www.microair.com.au/admin/uploads/documents/M760N2installusermanual01R11.pdf Phil Matheson VH-PKR mathes...@dodo.com.au 0358833588 Australia Web Page http://www.philskr2.50megs.com/ See VW Engines http://www.vw-engines.com/ www.homebuilt-aviation.com/
KR> N40MK
Off topic I have heard that N40MK was purchased by someone from down under?? Does anyone know who that may have been, so I can chase them up please??? I'm still trying to get all Aussie KR flyers and builders together. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> d shackles
Chris AN115. Check the A/Spruce web page A115-21 are for 3/32 and 1/8 cable. Mark L has them on his web page http://home.hiwaay.net/~langford/kcontrol.html Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Rudder Trim.
Parley Great idea. But being from another country, Australia, we often use different names for the same things. SO, would you happen to have a photo of the window crank to save confusion. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> RE: rudder size
Can anyone tell me if they feel the rudder size is adequate on the KR, > > > especially in a heavy crosswind I have only flown one KR but I have not heard anyone having concerns with the standard rudder being under sized. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Dragonfly canopy?
I'm wondering if that canopy will fit a KR that has been widened? Thanks all, Mark Mark welcome. YES The canopies are very flexible, and you make it fit your own KR. as you know most ,if not all KR's are different. You make canopy rails to fit your fuse, and cut down the canopy to suit the rails,front deck and turtle deck. It's not as easy as it sounds, but Mark L and J,as well as Larry, and Dan, all have great detail on their web pages to help. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Wed Photo
I have most of my KR complete. I added a update photo to the main page of my web page. www.philskr2.50megs.com Still lots of small things to do. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Front deck modification
Tony Wrote Would like any pic's you my have of the installlation and any challenges you may have encountered with this set-up. Much thanks! Tony out! --- I'm sure you will find all the photo's an info you need on Mark L's or Mark J's web pages. I have some on my web , but I think the others are better displayed. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> KR2 for sale in NZ
http://www.trademe.co.nz/Trade-Me-Motors/Aircraft/auction-83697956.htm This is one LONG link!!! >From Peter in NZ. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Intake Manifold - Oil cooler relocation.
Dan Before I mounted my cooler under and behind the engine, I was going to mount it flat against the firewall ( or about 1 inch or so off it)and use the fire wall as the outlet, allowing the air to run down the firewall and exit out the bottom.( with a light guard) OR I was going to mount if on it's edge, on the firewall running along side the cowl, with air inlets as I have on my cooler now, and have the outlet through the back edge of cowl on one side, and add exit slots like you see in the Vintage Car bonnet. I would seal outlet to cooler with foam, so the cooler would not be removed with cowl. I would have braced the cooler to the firewall and off the engine mount. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Front deck modification
Getting close to either cutting it open or leaving it alone.. Thanks for the help. Ron -- Ron I would cut along the top of the longerons, I added a ply triangle to the front cross member in front of the panel, where it joins the longerons, and I placed piano hinges along the longerons, It would take to long to explain, but Mark Langford's page explains it the best ( Thanks again Mark) Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Spar bolts at WAFs
Australian Standards will not allow the 4 separate bolts per spar. They insist on Two bolts with spacer. I used thick wall 4130 spacer and lock nuts. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Wellcome Max
Max welcome to the KR net, and hope you are able to complete your KR1b. I'm sure you find all the help you will need, from all these great guys and girls. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> KR2S Plans
I posted Australian Bank Cheque off to RR on the 6th Dec 06. My plans arrived today 2nd Jan 07. Not to bad, and did not have to hassle them. Thanks R & R. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> KR Builders Workshop Program
Bill What a great incentive for others. Here in Australia we an RV guy who does the same thing and he is always busy. I have considered the same thing many times but my work would be a problem. Good luck and I think you will be on a winner! Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> G Meter
Thanks All Yes I got the wire size, I have sent an email to the maker, But being XMAS, no one home, so you guys are the next best thing Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> new builder
Max Welcome to the list. I can not help you out with the KR1-B, but I'm sure someone will be able to. Phil Matheson VH-PKR mathes...@dodo.com.au 0358833588 Australia Web Page http://www.philskr2.50megs.com/ See VW Engines http://www.vw-engines.com/ www.homebuilt-aviation.com/
KR> G Meter
I fitted a GT-50 G meter into my KR yesterday from A/Spruce. Has anyone used one?, the instructions say to protect the wiring with a fuse or c/breaker, but they do not say what size fuse to place in wire 3 & 4. See link below http://www.fdatasystems.com/GT_50.htm Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> New flying locations.
Lee You are most welcome to drop in to my place ( Down under) as soon as you get those larger fuel tanks fitted. Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com
KR> Props
I was always told the 3 was for show and 2 for go. But Ron Slender ( VW Engines Aust)rang me the other night and said they have been testing a new Bolly 3 blade on they RG2000 and it out climbed, out cruised, and reduced the take off distance quite considerably by ONLY replacing the Prop. Go figure.? Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com
KR> 150 HP KR?/ REPLIES Please READ!!!!
Kenneth! and all others Please do not send the original message in the reply. To fix the problem!!! 1- Go to TOOLS at the top of your outlook express. 2- Click on Internet Options 3- Click on SEND 4- Make sure the " Include Message in Reply" box DOES NOT have a TICK in the box !!! This will then only send your reply back to the KR net and help stop all the extra waste of space!!!!!! Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Web Page Photo
Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/
KR> Web Page Photo
Sorry. try this one. I have added another photo of a beautiful KR to my web page, on the flying KR page www.philskr2.50megs.com Herry Rudyanto: PK-SKV. Jakarta, Indonesia Phil Matheson VH-PKR Australia KR Web Page www.philskr2.50megs.com http://www.vw-engines.com/