RE: tail stock on the LOM

[Bill Bulkeley]

Ok I made it on my metal lathe for my model 900 mill.

Using 2 bearings so it would be more stable when slipped over the existing 
mills dead centre

And yes the ID does mach the shaft of the mills dead centre.

Bill

 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Russ Veinot
Sent: Monday, 6 November 2017 1:49 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: tail stock on the LOM

 

3 questions (approximately), 

who made the live center? Was it machined special?

Why showing 2 bearings?  Does it need both ? 

Does the bearing ID match the diameter of the original shaft tip?

 

russ

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Bill Bulkeley
Sent: Sunday, November 05, 2017 6:55 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: tail stock on the LOM

 

This is how i solved the live centre problem with my lom it just slips on

 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Russ Veinot
Sent: Monday, 6 November 2017 9:14 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: tail stock on the LOM

 

If your tailstock has a MT-2 then you can use a standard live center?  I wish I 
had that.  I have just a solid rod grind to a point,  lots of friction under 
use.  That’s the part I don’t like.

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE
Sent: Sunday, November 05, 2017 3:55 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: tail stock on the LOM

 

my old 1000ex has a De-sta-co clamp on the tail stock with a MT-2 .There is not 
a lot of difference between the cam and ... but I like what I have. ;-)

 

C.A.G.

 

  _  

From: "russ veinot" 
To: "Legacy Ornamental Mills" 
Sent: Sunday, November 5, 2017 11:33:00 AM
Subject: tail stock on the LOM

 

i still use my original tailstock with the cam tensioner.  i am curious if 
anyone has this same set up?  was it used on other models (which models)?  if 
you changed your, how?  i would like to change mine, but maybe not have to 
reinvent the wheel :>)  looking for ideas !!

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 


 

 

Virus-free.  

 www.avg.com 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are 

Re: Need LOM dogs and split nut

[MAX LATHAM]

Got mine from Grizzly



http://www.grizzly.com/products/Cupped-Live-Center-for-Wood-Lathe-MT2/H3404?utm_campaign=zPage_source=grizzly.com

[http://cdn0.grizzly.com/grizzly2/images/griz-ind-short-red-gold-matted.png]

Cupped Live Center for Wood Lathe - MT2 | Grizzly 
Industrial
www.grizzly.com
Cupped centers provide better grip and prevent splitting. All ball bearing 
construction results in very little turning resistance even when loaded.






From: legacy-ornamental-mills@googlegroups.com 
 on behalf of CURTIS GEORGE 

Sent: Sunday, November 5, 2017 6:58 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut

Lathe Live Center
[Lathe Live 
Center]
Lathe Live Center


Lathe Live Center provides for smooth, friction-free turning without messy 
lubricants

Premier-quality Lathe Live Center features precision ball bearing construction 
for friction-free tip rotation without the need for beeswax or similar 
lubricants. As a result, your workpiece will turn more smoothly and quietly 
without the fear of unsightly burning, which, under certain circumstances, can 
allow your non-bearing Cup Center to loosen its grip on your stock and effect 
the accuracy of your cuts. Its #2 Morse taper shaft slips easily into your MARK 
V’s Lathe Tailstock.

IMPORTANT: This Live Center is required when using Shopsmith’s Lathe Duplicator 
(555638).


505602 Lathe Live Center ...   $41.99
(Item may be on back-order or is made upon ordering

You Might Also Be Interested In:

Lathe Drive Center ...  
$29.99

Product Reviews

Currently no reviews - you can be the first to review this item

[Create your own 
review]


Order on the Web or by Phone, if you prefer -- 1-937-890-5197.

Call before 4:30 PM Eastern Time


From: "CURTIS GEORGE" 
To: legacy-ornamental-mills@googlegroups.com
Sent: Sunday, November 5, 2017 5:12:06 PM
Subject: Re: Need LOM dogs and split nut

Hello guys.
the face-plate idea is OK. but for the money the indexing hubs are the best 
tool in the arsenal of tools that Legacy ever made.   Hopefully Cindy can come 
through for you? If not there are others out there that can make them... the 
Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. 
(Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL!

C.A.G.


From: "Joe G" 
To: legacy-ornamental-mills@googlegroups.com
Sent: Sunday, November 5, 2017 3:46:56 PM
Subject: Re: Need LOM dogs and split nut

Faceplate  great idea but i'll need 4 for the many steps I do..


On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot 
> wrote:

Excellent Suggestion !!?!!



From: 
legacy-ornamental-mills@googlegroups.com
 
[mailto:legacy-ornamental-mills@googlegroups.com]
 On Behalf Of Michael Kratky
Sent: Sunday, November 05, 2017 8:18 AM
To: 
legacy-ornamental-mills@googlegroups.com
Subject: RE: Need LOM dogs and split nut



There’s always a lathe faceplate:



[https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg]





From: 
legacy-ornamental-mills@googlegroups.com
 [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G
Sent: Saturday, November 04, 2017 10:12 PM
To: 
legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut



[Inline image 1]I have the threaded headstock with looks like a #2 MT

I do have  1" X 8 thread check but it 

RE: tail stock on the LOM

[Russ Veinot]

3 questions (approximately), 

who made the live center? Was it machined special?

Why showing 2 bearings?  Does it need both ? 

Does the bearing ID match the diameter of the original shaft tip?

 

russ

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Bill Bulkeley
Sent: Sunday, November 05, 2017 6:55 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: tail stock on the LOM

 

This is how i solved the live centre problem with my lom it just slips on

 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Russ Veinot
Sent: Monday, 6 November 2017 9:14 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: tail stock on the LOM

 

If your tailstock has a MT-2 then you can use a standard live center?  I wish I 
had that.  I have just a solid rod grind to a point,  lots of friction under 
use.  That’s the part I don’t like.

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE
Sent: Sunday, November 05, 2017 3:55 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: tail stock on the LOM

 

my old 1000ex has a De-sta-co clamp on the tail stock with a MT-2 .There is not 
a lot of difference between the cam and ... but I like what I have. ;-)

 

C.A.G.

 

  _  

From: "russ veinot" 
To: "Legacy Ornamental Mills" 
Sent: Sunday, November 5, 2017 11:33:00 AM
Subject: tail stock on the LOM

 

i still use my original tailstock with the cam tensioner.  i am curious if 
anyone has this same set up?  was it used on other models (which models)?  if 
you changed your, how?  i would like to change mine, but maybe not have to 
reinvent the wheel :>)  looking for ideas !!

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 


 

 

Virus-free.  

 www.avg.com 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Tail stock on the LOM

['joe biunno' via Legacy Ornamental Mills]

Thanks Mike!

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Need LOM dogs and split nut

[CURTIS GEORGE]

Lathe Live Center 
Lathe Live Center 





Lathe Live Center provides for smooth, friction-free turning without messy 
lubricants 

Premier-quality Lathe Live Center features precision ball bearing construction 
for friction-free tip rotation without the need for beeswax or similar 
lubricants. As a result, your workpiece will turn more smoothly and quietly 
without the fear of unsightly burning, which, under certain circumstances, can 
allow your non-bearing Cup Center to loosen its grip on your stock and effect 
the accuracy of your cuts. Its #2 Morse taper shaft slips easily into your MARK 
V’s Lathe Tailstock. 

IMPORTANT : This Live Center is required when using Shopsmith’s Lathe 
Duplicator (555638). 




505602 Lathe Live Center ... $41.99 
(Item may be on back-order or is made upon ordering 
You Might Also Be Interested In: 


Lathe Drive Center ... $29.99 
Product Reviews 


Currently no reviews - you can be the first to review this item 








Order on the Web or by Phone, if you prefer -- 1-937-890-5197 . 

Call before 4:30 PM Eastern Time 

- Original Message -

From: "CURTIS GEORGE"  
To: legacy-ornamental-mills@googlegroups.com 
Sent: Sunday, November 5, 2017 5:12:06 PM 
Subject: Re: Need LOM dogs and split nut 

Hello guys. 
the face-plate idea is OK. but for the money the indexing hubs are the best 
tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come 
through for you? If not there are others out there that can make them... the 
Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. 
(Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! 

C.A.G. 

- Original Message -

From: "Joe G"  
To: legacy-ornamental-mills@googlegroups.com 
Sent: Sunday, November 5, 2017 3:46:56 PM 
Subject: Re: Need LOM dogs and split nut 

Faceplate great idea but i'll need 4 for the many steps I do.. 


On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot < ru...@yknotwood.com > wrote: 





Excellent Suggestion !!?!! 




From: legacy-ornamental-mills@googlegroups.com [mailto: 
legacy-ornamental-mills@googlegroups.com ] On Behalf Of Michael Kratky 
Sent: Sunday, November 05, 2017 8:18 AM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: RE: Need LOM dogs and split nut 




There’s always a lathe faceplate: 










From: legacy-ornamental-mills@googlegroups.com [ 
mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G 
Sent: Saturday, November 04, 2017 10:12 PM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: Re: Need LOM dogs and split nut 





I have the threaded headstock with looks like a #2 MT 


I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at top 





On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: 


BUY EXTRA !! :>) 

Oh, I already said that. Does the headstock have a threaded head for adding a 4 
jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it 
have the #1 morse taper headstock? 




From: legacy-ornamental-mills@googlegroups.com [mailto: 
legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen 
Sent: Saturday, November 04, 2017 7:47 PM 
To: Legacy Ornamental Mills 



Subject: Re: Need LOM dogs and split nut 





Thanks Tim, Ill call back Monday! 






On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: 

Call Legacy back and ask for Cindy. She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < 
ru...@yknotwood.com > wrote: 
> 
> BUY EXTRA !! :>) 
> 
> 
> 
> From: legacy-orna...@googlegroups.com [ 
> mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
> 
> 
> 
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
> 
> No call yet..fingers crossed! 
> 
> 
> 
> 
> 
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: 
> 
> Hello again Joe 
> 
> 
> 
> do you still have the old split nut? Its just the upper half you need? If so 
> I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. 
> I can tap a piece of durlin (SP?) plastic for you, then you can cut it to 
> fit... 
> 
> Please let me know if you still need help on this? 
> 
> more latter. 
> 
> 
> 
> C.A.G. 
> 
> 
> 
> _ 
> 
> From: "Joe Gassen" < words...@gmail.com > 
> To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > 
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
> 
> 
> 
> I sent an e-mail but later found this board. 
> 
> I have an older steel rail LOM and have recently begun to use it again. 
> 
> I need at least two of the 4 prong dogs that fit the 

Re: tail stock on the LOM

[CURTIS GEORGE]

Yes I use a live center most of the time. I remember someone (I think it was 
Tim) who made a live center for the Legacy's new tail stock. (More then a few 
years ago.) If I remember correctly they threaded the shaft and then added a 
live center on to the shaft. (I may have been a Shop-Smith I know that has a 
1/2 -24 thread on the live center.) It should be in our archives..? 

C.A.G. 

- Original Message -

From: "Russ Veinot"  
To: legacy-ornamental-mills@googlegroups.com 
Sent: Sunday, November 5, 2017 5:13:41 PM 
Subject: RE: tail stock on the LOM 



If your tailstock has a MT-2 then you can use a standard live center? I wish I 
had that. I have just a solid rod grind to a point, lots of friction under use. 
That’s the part I don’t like. 




From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE 
Sent: Sunday, November 05, 2017 3:55 PM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: Re: tail stock on the LOM 





my old 1000ex has a De-sta-co clamp on the tail stock with a MT-2 .There is not 
a lot of difference between the cam and ... but I like what I have. ;-) 





C.A.G. 



- Original Message -



From: "russ veinot" < ru...@yknotwood.com > 
To: "Legacy Ornamental Mills" < legacy-ornamental-mills@googlegroups.com > 
Sent: Sunday, November 5, 2017 11:33:00 AM 
Subject: tail stock on the LOM 





i still use my original tailstock with the cam tensioner. i am curious if 
anyone has this same set up? was it used on other models (which models)? if you 
changed your, how? i would like to change mine, but maybe not have to reinvent 
the wheel :>) looking for ideas !! 




-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 





-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 



-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

RE: Need LOM dogs and split nut

[Russ Veinot]

OK, to me, simple is drilling for a 1” dowel and cut it off after.  No money 
spend.  Should have enough scrap to do this without leaving the shop.  With the 
face plate, you would only need one.  Flat piece of plywood with 4 cleats to 
hold the leg like a “wrench on a bolt”.  They slip in and out instantly and 
held in with tailstock.  Or one piece of flat plywood with a lag bolt screwed 
through it and mount on faceplate.  Lots of NTI (nothing to it :>) ways.

 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE
Sent: Sunday, November 05, 2017 4:12 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut

 

Hello guys.

the face-plate idea is OK. but for the money the indexing hubs are the best 
tool in the arsenal of tools that Legacy ever made.   Hopefully Cindy can come 
through for you? If not there are others out there that can make them... the 
Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. 
(Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL!

 

C.A.G. 

 

  _  

From: "Joe G" 
To: legacy-ornamental-mills@googlegroups.com
Sent: Sunday, November 5, 2017 3:46:56 PM
Subject: Re: Need LOM dogs and split nut

 

Faceplate  great idea but i'll need 4 for the many steps I do..

 

 

On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot  wrote:



Excellent Suggestion !!?!!

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Michael Kratky
Sent: Sunday, November 05, 2017 8:18 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Need LOM dogs and split nut

 

There’s always a lathe faceplate:

 

https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg

 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G
Sent: Saturday, November 04, 2017 10:12 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut

 

Inline image 1I have the threaded headstock with looks like a #2 MT

I do have  1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at topInline image 2

 

On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot  wrote:

BUY EXTRA !! :>)

Oh, I already said that.  Does the headstock have a threaded head for adding a 
4 jaw chuck?  I rarely use my LOM dogs anymore since adding one to my LOM.  
Does it have the #1 morse taper headstock?

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen
Sent: Saturday, November 04, 2017 7:47 PM
To: Legacy Ornamental Mills


Subject: Re: Need LOM dogs and split nut

 

Thanks Tim, Ill call back Monday!

 

 

On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote:

Call Legacy back and ask for Cindy.  She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot 
 wrote:
>
> BUY EXTRA !! :>) 
>
>
>
> From: legacy-orna...@googlegroups.com 
> [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
>
>
>
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
>
> No call yet..fingers crossed! 
>
>
>
>
>
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE  wrote: 
>
> Hello again Joe 
>
>
>
> do you still have the old split nut?  Its just the upper half you need? If so 
> I may be some help for you.  I own a home made tap for the 5/8 x 4 acme 
> screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it 
> to fit... 
>
> Please let me know if you still need help on this? 
>
> more latter. 
>
>
>
> C.A.G. 
>
>
>
>   _  
>
> From: "Joe Gassen"  
> To: "Legacy Ornamental Mills"  
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
>
>
>
> I sent an e-mail but later found this board. 
>
> I have an older steel rail LOM and have recently begun to use it again. 
>
> I need at least two of the 4 prong dogs that fit the headstock mad will also 
> need a split nut in the future for the 5/8 acme. 
>
> Any help will be appreciated since I see Legacy no longer supports the older 
> LOM s and have also taken down the old training videos. 
>
> Thx all 
>
>
>
> Joe 
>
>
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email 

Re: Tail stock on the LOM

['joe biunno' via Legacy Ornamental Mills]

Ok, been following the group but not commenting...a lot going on at work and 
personally...one thing to note here is that I have to move my shop to a new 
location... so we will see how well my beast breaks down and transports...The 
base, the two,joined machines(1800 & 1200), the sopport cabinet and accessory 
cart, etc I will take photos and post the procedure...back to the tailstock 
issue...I am replying using my phone, not my of, so I cannot provide a 
link...but if you search "tailstock mod", I am sure you will find it...in a 
brief recap, I was able to find a tailstock from a small lathe on eBay, for 
little money...had a #2 Morse taper, adjustment with a hand wheel and you lock 
it down... it's casting was square, which made adapting it very quick and 
easy... certainly no where near as nice as john preston's, but something that I 
feel any member of the group could do as a Saturday morning project... just 
need to find the right tailstock on eBay...but it certainly is much better than 
the original cam action that came from legacy and worth the time and money... 
Joe 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

RE: tail stock on the LOM

[Russ Veinot]

If your tailstock has a MT-2 then you can use a standard live center?  I wish I 
had that.  I have just a solid rod grind to a point,  lots of friction under 
use.  That’s the part I don’t like.

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of CURTIS GEORGE
Sent: Sunday, November 05, 2017 3:55 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: tail stock on the LOM

 

my old 1000ex has a De-sta-co clamp on the tail stock with a MT-2 .There is not 
a lot of difference between the cam and ... but I like what I have. ;-)

 

C.A.G.

 

  _  

From: "russ veinot" 
To: "Legacy Ornamental Mills" 
Sent: Sunday, November 5, 2017 11:33:00 AM
Subject: tail stock on the LOM

 

i still use my original tailstock with the cam tensioner.  i am curious if 
anyone has this same set up?  was it used on other models (which models)?  if 
you changed your, how?  i would like to change mine, but maybe not have to 
reinvent the wheel :>)  looking for ideas !!

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Need LOM dogs and split nut

[CURTIS GEORGE]

Hello guys. 
the face-plate idea is OK. but for the money the indexing hubs are the best 
tool in the arsenal of tools that Legacy ever made. Hopefully Cindy can come 
through for you? If not there are others out there that can make them... the 
Hubs are Simple, Efficient,& Practical... (ESP. or in other woods its KISS. 
(Keep,It Simple, Stupid.) for the price those hubs are a GREAT DEAL! 

C.A.G. 

- Original Message -

From: "Joe G"  
To: legacy-ornamental-mills@googlegroups.com 
Sent: Sunday, November 5, 2017 3:46:56 PM 
Subject: Re: Need LOM dogs and split nut 

Faceplate great idea but i'll need 4 for the many steps I do.. 


On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot < ru...@yknotwood.com > wrote: 





Excellent Suggestion !!?!! 




From: legacy-ornamental-mills@googlegroups.com [mailto: 
legacy-ornamental-mills@googlegroups.com ] On Behalf Of Michael Kratky 
Sent: Sunday, November 05, 2017 8:18 AM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: RE: Need LOM dogs and split nut 




There’s always a lathe faceplate: 










From: legacy-ornamental-mills@googlegroups.com [ 
mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G 
Sent: Saturday, November 04, 2017 10:12 PM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: Re: Need LOM dogs and split nut 





I have the threaded headstock with looks like a #2 MT 


I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at top 





On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: 


BUY EXTRA !! :>) 

Oh, I already said that. Does the headstock have a threaded head for adding a 4 
jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it 
have the #1 morse taper headstock? 




From: legacy-ornamental-mills@googlegroups.com [mailto: 
legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen 
Sent: Saturday, November 04, 2017 7:47 PM 
To: Legacy Ornamental Mills 



Subject: Re: Need LOM dogs and split nut 





Thanks Tim, Ill call back Monday! 






On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: 

Call Legacy back and ask for Cindy. She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < 
ru...@yknotwood.com > wrote: 
> 
> BUY EXTRA !! :>) 
> 
> 
> 
> From: legacy-orna...@googlegroups.com [ 
> mailto:legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
> 
> 
> 
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
> 
> No call yet..fingers crossed! 
> 
> 
> 
> 
> 
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: 
> 
> Hello again Joe 
> 
> 
> 
> do you still have the old split nut? Its just the upper half you need? If so 
> I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. 
> I can tap a piece of durlin (SP?) plastic for you, then you can cut it to 
> fit... 
> 
> Please let me know if you still need help on this? 
> 
> more latter. 
> 
> 
> 
> C.A.G. 
> 
> 
> 
> _ 
> 
> From: "Joe Gassen" < words...@gmail.com > 
> To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > 
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
> 
> 
> 
> I sent an e-mail but later found this board. 
> 
> I have an older steel rail LOM and have recently begun to use it again. 
> 
> I need at least two of the 4 prong dogs that fit the headstock mad will also 
> need a split nut in the future for the 5/8 acme. 
> 
> Any help will be appreciated since I see Legacy no longer supports the older 
> LOM s and have also taken down the old training videos. 
> 
> Thx all 
> 
> 
> 
> Joe 
> 
> 
> 


-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 


-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 





-- 
You received this message because you are subscribed to 

Re: tail stock on the LOM

[CURTIS GEORGE]

my old 1000ex has a De-sta-co clamp on the tail stock with a MT-2 .There is not 
a lot of difference between the cam and ... but I like what I have. ;-) 

C.A.G. 

- Original Message -

From: "russ veinot"  
To: "Legacy Ornamental Mills"  
Sent: Sunday, November 5, 2017 11:33:00 AM 
Subject: tail stock on the LOM 

i still use my original tailstock with the cam tensioner. i am curious if 
anyone has this same set up? was it used on other models (which models)? if you 
changed your, how? i would like to change mine, but maybe not have to reinvent 
the wheel :>) looking for ideas !! 



-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Need LOM dogs and split nut

[Joe G]

Faceplate  great idea but i'll need 4 for the many steps I do..


On Sun, Nov 5, 2017 at 8:29 AM, Russ Veinot  wrote:

> Excellent Suggestion !!?!!
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com [mailto:
> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Michael Kratky
> *Sent:* Sunday, November 05, 2017 8:18 AM
> *To:* legacy-ornamental-mills@googlegroups.com
> *Subject:* RE: Need LOM dogs and split nut
>
>
>
> There’s always a lathe faceplate:
>
>
>
> [image: https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg]
>
>
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com [
> mailto:legacy-ornamental-mills@googlegroups.com
> ] *On Behalf Of *Joe G
> *Sent:* Saturday, November 04, 2017 10:12 PM
> *To:* legacy-ornamental-mills@googlegroups.com
> *Subject:* Re: Need LOM dogs and split nut
>
>
>
> [image: Inline image 1]I have the threaded headstock with looks like a #2
> MT
>
> I do have  1" X 8 thread check but it only opens to 3" I think. The legs I
> were turning for a table are 4" and 5" Sq at top[image: Inline image 2]
>
>
>
> On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot  wrote:
>
> BUY EXTRA !! :>)
>
> Oh, I already said that.  Does the headstock have a threaded head for
> adding a 4 jaw chuck?  I rarely use my LOM dogs anymore since adding one to
> my LOM.  Does it have the #1 morse taper headstock?
>
>
>
> *From:* legacy-ornamental-mills@googlegroups.com [mailto:
> legacy-ornamental-mills@googlegroups.com] *On Behalf Of *Joe Gassen
> *Sent:* Saturday, November 04, 2017 7:47 PM
> *To:* Legacy Ornamental Mills
>
>
> *Subject:* Re: Need LOM dogs and split nut
>
>
>
> Thanks Tim, Ill call back Monday!
>
>
>
> On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote:
>
> Call Legacy back and ask for Cindy.  She is in charge of the parts for the
> manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot
>  wrote:
> >
> > BUY EXTRA !! :>)
> >
> >
> >
> > From: legacy-orna...@googlegroups.com [mailto:legacy-ornamental-
> mi...@googlegroups.com ] On
> Behalf Of Joe G
> > Sent: Friday, November 03, 2017 6:51 PM
> > To: legacy-orna...@googlegroups.com
> > Subject: Re: Need LOM dogs and split nut
> >
> >
> >
> > Thanks guys for the help. I called Legacy and the man that answered said
> he would have someone call me back and he thought they had the parts.
> >
> > No call yet..fingers crossed!
> >
> >
> >
> >
> >
> > On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE 
> wrote:
> >
> > Hello again Joe
> >
> >
> >
> > do you still have the old split nut?  Its just the upper half you need?
> If so I may be some help for you.  I own a home made tap for the 5/8 x 4
> acme screw. I can tap a piece of durlin (SP?) plastic for you, then you can
> cut it to fit...
> >
> > Please let me know if you still need help on this?
> >
> > more latter.
> >
> >
> >
> > C.A.G.
> >
> >
> >
> >   _
> >
> > From: "Joe Gassen" 
> > To: "Legacy Ornamental Mills" 
> > Sent: Friday, November 3, 2017 12:07:33 PM
> > Subject: Need LOM dogs and split nut
> >
> >
> >
> > I sent an e-mail but later found this board.
> >
> > I have an older steel rail LOM and have recently begun to use it again.
> >
> > I need at least two of the 4 prong dogs that fit the headstock mad will
> also need a split nut in the future for the 5/8 acme.
> >
> > Any help will be appreciated since I see Legacy no longer supports the
> older LOM s and have also taken down the old training videos.
> >
> > Thx all
> >
> >
> >
> > Joe
> >
> >
> >
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To post to this group, send email to legacy-ornamental-mills@
> googlegroups.com.
> Visit this group at https://groups.google.com/
> group/legacy-ornamental-mills.
> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To post to this group, send email to legacy-ornamental-mills@
> googlegroups.com.
> Visit this group at https://groups.google.com/
> group/legacy-ornamental-mills.
> For more options, visit https://groups.google.com/d/optout.
>
>
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To post to this group, send email to 

RE: Tail stock on the LOM

[Russ Veinot]

Richard,

The only thing I am aware of I am missing is “riding sidesaddle”, is there 
something else :>)

 

I don’t understand why it has taken me so long to want to fix this darn thing.  
This topic is probably old topic but now I want to address it, I am old . . . I 
forget :>)  wait till I start telling the same joke over and over.

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Richard Ellis
Sent: Sunday, November 05, 2017 11:25 AM
To: Legacy Ornamental Mills
Subject: Re: Tail stock on the LOM

 

Russ

Yes the same camlock on my Wodchuck and my Revo, Not a clever idea in my 
opinion As for the Revo You don't know what you are missing? 

Richard

On Sunday, November 5, 2017 at 5:12:52 PM UTC, Va Oak wrote:

Ok, Joe Biuno, time for you to chime in!  Show Russ the "museum quality" 
work/modifications that you do.  
I'm sure that on at least one of your LOMs you have improved the tensioner.
Russ - get ready to be impressed!
Mac

  _  

  _  

-Original Message- 
From: russ veinot 
Sent: Nov 5, 2017 11:33 AM 
To: Legacy Ornamental Mills 
Subject: tail stock on the LOM 

i still use my original tailstock with the cam tensioner.  i am curious if 
anyone has this same set up?  was it used on other models (which models)?  if 
you changed your, how?  i would like to change mine, but maybe not have to 
reinvent the wheel :>)  looking for ideas !!

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Tail stock on the LOM

[Richard Ellis]

Russ
Yes the same camlock on my Wodchuck and my Revo, Not a clever idea in my 
opinion As for the Revo You don't know what you are 
missing? 
Richard

On Sunday, November 5, 2017 at 5:12:52 PM UTC, Va Oak wrote:
>
> Ok, Joe Biuno, time for you to chime in!  Show Russ the "museum quality" 
> work/modifications that you do.  
> I'm sure that on at least one of your LOMs you have improved the tensioner.
> Russ - get ready to be impressed!
> Mac
> --
> --
>
> -Original Message- 
> From: russ veinot 
> Sent: Nov 5, 2017 11:33 AM 
> To: Legacy Ornamental Mills 
> Subject: tail stock on the LOM 
>
> i still use my original tailstock with the cam tensioner.  i am curious if 
> anyone has this same set up?  was it used on other models (which models)?  
> if you changed your, how?  i would like to change mine, but maybe not have 
> to reinvent the wheel :>)  looking for ideas !!
>
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Tail stock on the LOM

[MWF]

Ok, Joe Biuno, time for you to chime in!  Show Russ the "museum quality" work/modifications that you do.  I'm sure that on at least one of your LOMs you have improved the tensioner.Russ - get ready to be impressed!Mac-Original Message-
From: russ veinot 
Sent: Nov 5, 2017 11:33 AM
To: Legacy Ornamental Mills 
Subject: tail stock on the LOM

i still use my original tailstock with the cam tensioner.  i am curious if anyone has this same set up?  was it used on other models (which models)?  if you changed your, how?  i would like to change mine, but maybe not have to reinvent the wheel :>)  looking for ideas !!






-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

tail stock on the LOM

[russ veinot]

i still use my original tailstock with the cam tensioner.  i am curious if 
anyone has this same set up?  was it used on other models (which models)?  
if you changed your, how?  i would like to change mine, but maybe not have 
to reinvent the wheel :>)  looking for ideas !!

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

RE: Need LOM dogs and split nut

[Russ Veinot]

Excellent Suggestion !!?!!

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Michael Kratky
Sent: Sunday, November 05, 2017 8:18 AM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Need LOM dogs and split nut

 

There’s always a lathe faceplate:

 

https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg

 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G
Sent: Saturday, November 04, 2017 10:12 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut

 

Inline image 1I have the threaded headstock with looks like a #2 MT

I do have  1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at topInline image 2

 

On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot  wrote:

BUY EXTRA !! :>)

Oh, I already said that.  Does the headstock have a threaded head for adding a 
4 jaw chuck?  I rarely use my LOM dogs anymore since adding one to my LOM.  
Does it have the #1 morse taper headstock?

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen
Sent: Saturday, November 04, 2017 7:47 PM
To: Legacy Ornamental Mills


Subject: Re: Need LOM dogs and split nut

 

Thanks Tim, Ill call back Monday!



On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote:

Call Legacy back and ask for Cindy.  She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot 
 wrote:
>
> BUY EXTRA !! :>) 
>
>
>
> From: legacy-orna...@googlegroups.com 
> [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
>
>
>
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
>
> No call yet..fingers crossed! 
>
>
>
>
>
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE  wrote: 
>
> Hello again Joe 
>
>
>
> do you still have the old split nut?  Its just the upper half you need? If so 
> I may be some help for you.  I own a home made tap for the 5/8 x 4 acme 
> screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it 
> to fit... 
>
> Please let me know if you still need help on this? 
>
> more latter. 
>
>
>
> C.A.G. 
>
>
>
>   _  
>
> From: "Joe Gassen"  
> To: "Legacy Ornamental Mills"  
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
>
>
>
> I sent an e-mail but later found this board. 
>
> I have an older steel rail LOM and have recently begun to use it again. 
>
> I need at least two of the 4 prong dogs that fit the headstock mad will also 
> need a split nut in the future for the 5/8 acme. 
>
> Any help will be appreciated since I see Legacy no longer supports the older 
> LOM s and have also taken down the old training videos. 
>
> Thx all 
>
>
>
> Joe 
>
>
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at 

RE: Need LOM dogs and split nut

[Michael Kratky]

There’s always a lathe faceplate:

 

https://www.pennstateind.com/mm5/graphics/0001/CF3J_70x70.jpg

 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G
Sent: Saturday, November 04, 2017 10:12 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: Re: Need LOM dogs and split nut

 

Inline image 1I have the threaded headstock with looks like a #2 MT

I do have  1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at topInline image 2

 

On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot  wrote:

BUY EXTRA !! :>)

Oh, I already said that.  Does the headstock have a threaded head for adding a 
4 jaw chuck?  I rarely use my LOM dogs anymore since adding one to my LOM.  
Does it have the #1 morse taper headstock?

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen
Sent: Saturday, November 04, 2017 7:47 PM
To: Legacy Ornamental Mills


Subject: Re: Need LOM dogs and split nut

 

Thanks Tim, Ill call back Monday!



On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote:

Call Legacy back and ask for Cindy.  She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot 
 wrote:
>
> BUY EXTRA !! :>) 
>
>
>
> From: legacy-orna...@googlegroups.com 
> [mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
>
>
>
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
>
> No call yet..fingers crossed! 
>
>
>
>
>
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE  wrote: 
>
> Hello again Joe 
>
>
>
> do you still have the old split nut?  Its just the upper half you need? If so 
> I may be some help for you.  I own a home made tap for the 5/8 x 4 acme 
> screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it 
> to fit... 
>
> Please let me know if you still need help on this? 
>
> more latter. 
>
>
>
> C.A.G. 
>
>
>
>   _  
>
> From: "Joe Gassen"  
> To: "Legacy Ornamental Mills"  
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
>
>
>
> I sent an e-mail but later found this board. 
>
> I have an older steel rail LOM and have recently begun to use it again. 
>
> I need at least two of the 4 prong dogs that fit the headstock mad will also 
> need a split nut in the future for the 5/8 acme. 
>
> Any help will be appreciated since I see Legacy no longer supports the older 
> LOM s and have also taken down the old training videos. 
>
> Thx all 
>
>
>
> Joe 
>
>
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.
For more options, visit https://groups.google.com/d/optout.

Re: Need LOM dogs and split nut

[CURTIS GEORGE]

Hello Joe 
most of the Legacy's that I have seen have a MT-2 as well as a 1x8 thread on 
the head-stock/spindle. This means most of the lathe adapters you own should 
fit the Legacy, the MT-1 is to small for the Legacy, but you can buy MT 1-2 
adapters at any machine shop supply house, they are not expensive. 

C.A.G. 

- Original Message -

From: "Joe G"  
To: legacy-ornamental-mills@googlegroups.com 
Sent: Saturday, November 4, 2017 10:12:02 PM 
Subject: Re: Need LOM dogs and split nut 

I have the threaded headstock with looks like a #2 MT 
I do have 1" X 8 thread check but it only opens to 3" I think. The legs I were 
turning for a table are 4" and 5" Sq at top 

On Sat, Nov 4, 2017 at 8:40 PM, Russ Veinot < ru...@yknotwood.com > wrote: 





BUY EXTRA !! :>) 

Oh, I already said that. Does the headstock have a threaded head for adding a 4 
jaw chuck? I rarely use my LOM dogs anymore since adding one to my LOM. Does it 
have the #1 morse taper headstock? 




From: legacy-ornamental-mills@googlegroups.com [mailto: 
legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe Gassen 
Sent: Saturday, November 04, 2017 7:47 PM 
To: Legacy Ornamental Mills 

Subject: Re: Need LOM dogs and split nut 








Thanks Tim, Ill call back Monday! 






On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote: 

Call Legacy back and ask for Cindy. She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot < 
ru...@yknotwood.com > wrote: 
> 
> BUY EXTRA !! :>) 
> 
> 
> 
> From: legacy-orna...@googlegroups.com [mailto: 
> legacy-ornamental-mills@googlegroups.com ] On Behalf Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com 
> Subject: Re: Need LOM dogs and split nut 
> 
> 
> 
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
> 
> No call yet..fingers crossed! 
> 
> 
> 
> 
> 
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE < curtg...@wowway.com > wrote: 
> 
> Hello again Joe 
> 
> 
> 
> do you still have the old split nut? Its just the upper half you need? If so 
> I may be some help for you. I own a home made tap for the 5/8 x 4 acme screw. 
> I can tap a piece of durlin (SP?) plastic for you, then you can cut it to 
> fit... 
> 
> Please let me know if you still need help on this? 
> 
> more latter. 
> 
> 
> 
> C.A.G. 
> 
> 
> 
> _ 
> 
> From: "Joe Gassen" < words...@gmail.com > 
> To: "Legacy Ornamental Mills" < legacy-orna...@googlegroups.com > 
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs and split nut 
> 
> 
> 
> I sent an e-mail but later found this board. 
> 
> I have an older steel rail LOM and have recently begun to use it again. 
> 
> I need at least two of the 4 prong dogs that fit the headstock mad will also 
> need a split nut in the future for the 5/8 acme. 
> 
> Any help will be appreciated since I see Legacy no longer supports the older 
> LOM s and have also taken down the old training videos. 
> 
> Thx all 
> 
> 
> 
> Joe 
> 
> 
> 


-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 



-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 







-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group. 
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com . 
To post to this group, send email to legacy-ornamental-mills@googlegroups.com . 
Visit this group at https://groups.google.com/group/legacy-ornamental-mills . 
For more options, visit https://groups.google.com/d/optout . 

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To post to this group, send email to legacy-ornamental-mills@googlegroups.com.
Visit this group at https://groups.google.com/group/legacy-ornamental-mills.

RE: Need LOM dogs and split nut

[Russ Veinot]

You are on the money Bill.  The LOM uses the 1”-8TPI headstock with the #2 
morse taper almost always, **apparently even yours Jon **.   The #1 and #2 
tapers are not interchangeable.  There might be a #2 to #1 adaptor but don’t 
bother.  The #2 is most common among most wood lathes and LOM’s.  

 

You have a 3 choices that comes to mind.  

1)  You can buy a larger  chuck at about $200 or more

2) you can purchase the Penn State industries’ economy chuck (  
 
https://www.pennstateind.com/store/CUG3418CCX.html ) for $90 . It comes with a 
larger flat jaw set you could adapt for your use.

3) If you already have a smaller jaw chuck (Check? :>), you can drill a 1” hole 
in the end of your stock and glue a 1” dowel ( or less, size doesn’t matter) in 
it.  This can then be used to hold the headstock end of the leg in your chuck.  
After finishing, cut the dowel off flush.

 

The Penn state chuck comes with a lag screw so you could even drill a proper 
size hole in the leg and screw the leg on to lag screw (I guess this is kinda  
#4 choice :>). 

I really like my Penn State Chuck and rarely use the LOM dogs these days.

There are a couple of other solutions that would be more complicated that I 
could suggest if you want, but these 3 (4) are your easiest possibilities as I 
see it.

 

Hope this helps

Russ

 

P.S.  if you buy a new chuck, don’t buy extra :>)

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Bill Bulkeley
Sent: Saturday, November 04, 2017 9:39 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Need LOM dogs and split nut

 

I think it really depends on the size of your machine larger machines need 
larger morse tapers to handle heaver operations your machine will do.the larger 
the morse taper the more surface area it has to drive whatever you put in it

But in a medium size lathe or the legacy mill i like a number 2 morse which is 
as large as you can go and still have your 1inch by 8 threads for your chucks 
and stuff. You can always use sleeves to make a smaller morse tool fit but not 
the other way round

Just my opinion based on years of working in the metal working industry 

Bill 

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of MWF
Sent: Sunday, 5 November 2017 12:53 PM
To: legacy-ornamental-mills@googlegroups.com
Subject: RE: Need LOM dogs and split nut

 

OK guys - its been kinda "slow" on the LOM discussions lately - so here goes:

I'll toss this one out for discussion:

How does one determine if the headstock on their lathe (LOM or other brand) is 
a #1, #2, or a #3 Morse Taper? (Short of having a "known taper" piece of stock 
and seeing if it "fits" into your headstock.)

If given a choice of which taper to have on your device (lathe?) - which will 
you recommend - and WHY?

Thanks.
Mac

  _  

  _  

-Original Message- 
From: Russ Veinot 
Sent: Nov 4, 2017 9:40 PM 
To: legacy-ornamental-mills@googlegroups.com 
Subject: RE: Need LOM dogs and split nut 



BUY EXTRA !! :>)

Oh, I already said that.  Does the headstock have a threaded head for adding a 
4 jaw chuck?  I rarely use my LOM dogs anymore since adding one to my LOM.  
Does it have the #1 morse taper headstock?

 

From: legacy-ornamental-mills@googlegroups.com 
[mailto:legacy-ornamental-mills@googlegroups.com] On Behalf Of Joe Gassen
Sent: Saturday, November 04, 2017 7:47 PM
To: Legacy Ornamental Mills
Subject: Re: Need LOM dogs and split nut

 

Thanks Tim, Ill call back Monday!



On Saturday, November 4, 2017 at 4:40:55 PM UTC-5, Tim wrote:

Call Legacy back and ask for Cindy.  She is in charge of the parts for the 
manual machines the last time I checked.On Nov 3, 2017 5:05 PM, Russ Veinot 
 wrote:
>
> BUY EXTRA !! :>) 
>
> From: legacy-orna...@googlegroups.com   
> [mailto:legacy-ornamental-mills@googlegroups.com  ] On Behalf 
> Of Joe G 
> Sent: Friday, November 03, 2017 6:51 PM 
> To: legacy-orna...@googlegroups.com   
> Subject: Re: Need LOM dogs and split nut 
>
> Thanks guys for the help. I called Legacy and the man that answered said he 
> would have someone call me back and he thought they had the parts. 
>
> No call yet..fingers crossed! 
>
> On Fri, Nov 3, 2017 at 6:31 PM, CURTIS GEORGE   > wrote: 
>
> Hello again Joe 
>
> do you still have the old split nut?  Its just the upper half you need? If so 
> I may be some help for you.  I own a home made tap for the 5/8 x 4 acme 
> screw. I can tap a piece of durlin (SP?) plastic for you, then you can cut it 
> to fit... 
>
> Please let me know if you still need help on this? 
>
> more latter. 
>
> C.A.G. 
>   _  
>
> From: "Joe Gassen"  
> To: "Legacy Ornamental Mills"   > 
> Sent: Friday, November 3, 2017 12:07:33 PM 
> Subject: Need LOM dogs