subject:"Re\: Thin Stock support block dimensions"

Re: Thin Stock support block dimensions

2023-02-16 Thread 'Denson Ingram' via Legacy Ornamental Mills

Great job Mike, works just like it ought.DensonSent from Denson's iPhoneOn Feb 16, 2023, at 9:51 PM, Tim Ziegler  wrote:Good deal, with a pc of stock that long you may want the second one in there too. Then also lighter cuts and you will have it made.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Thu, Feb 16, 2023 at 7:54 PM Mike Newman  wrote:I was able to sneak out to the shop tonight to try out the thin stock support.  It worked almost perfect and much better than the first one I made.  Turned down a poplar blank for my first tapered walking stick and there was limited chatter.  Still a couple of things to pay attention to but definitely the way to go for me right now.<20230216_190339.jpg>On Wednesday, February 15, 2023 at 11:14:24 PM UTC-6 Curt George wrote:
Very nice, Mike.I think it should work well for you.Best of luck.C.A.G.





On Wednesday, February 15, 2023 at 06:44:51 PM EST, Mike Newman  wrote:



I finished my new thin stock support earlier tonight based on the info you guys provided.  I have not tried it yet but should work similar to the factory one.  I will throw another walking stick blank up on the LOM this weekend and see how it works.On Monday, February 13, 2023 at 10:48:26 PM UTC-6 Denson Ingram wrote:Yes sir you are welcome.DensonSent from my iPadOn Feb 13, 2023, at 9:40 PM, Tim Ziegler  wrote:Hey Denson thanks for jumping in on that. Great job.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills  wrote:Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman  wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support?  I finally found a block of the material that I can make my own, but wanted to get the dimensions.  Overall dimensions and then size/position of the v-notch should be all I need.  I will attach it to my cross member I used for my first trial design.  If anyone has one of the actual factory take a few measurements and post them or email me direct.  I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road?  thanks



-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com.




-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com.




-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com.




-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/640be98b-dc01-4a22-bbe5-f19a7c9a163dn%40googlegroups.com.






-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/93b9ab0c-db33-4070-b0fe-7e19733469bfn%40googlegroups.com.




-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msg

Re: Thin Stock support block dimensions

2023-02-13 Thread 'Denson Ingram' via Legacy Ornamental Mills

Yes sir you are welcome.DensonSent from my iPadOn Feb 13, 2023, at 9:40 PM, Tim Ziegler wrote:Hey Denson thanks for jumping in on that. Great job.Kind Regards,Timothy J. ZieglerZiegler WoodWork & Specialty14171 160th Ave.Foreston MN 56330320-294-5798 shop320-630-2243 cellOn Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills wrote:Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support? I finally found a block of the material that I can make my own, but wanted to get the dimensions. Overall dimensions and then size/position of the v-notch should be all I need. I will attach it to my cross member I used for my first trial design. If anyone has one of the actual factory take a few measurements and post them or email me direct. I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road? thanks

--
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com.

--
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com.

Re: Thin Stock support block dimensions

2023-02-13 Thread Tim Ziegler

Hey Denson thanks for jumping in on that. Great job.

Kind Regards,

Timothy J. Ziegler
Ziegler WoodWork & Specialty
14171 160th Ave.
Foreston MN 56330

320-294-5798 shop
320-630-2243 cell


On Mon, Feb 13, 2023 at 5:49 PM 'Denson Ingram' via Legacy Ornamental Mills
 wrote:

> Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick
> Denson
> Sent from Denson's iPhone
>
> On Feb 13, 2023, at 5:20 PM, Mike Newman  wrote:
>
> Does anyone already have the dimension for the hdpe blocks used on the
> factory thin stock support?  I finally found a block of the material that I
> can make my own, but wanted to get the dimensions.  Overall dimensions and
> then size/position of the v-notch should be all I need.  I will attach it
> to my cross member I used for my first trial design.  If anyone has one of
> the actual factory take a few measurements and post them or email me
> direct.  I can figure it out if nobody has a factory one, but thought I
> would quickly check before I go down that road?  thanks
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com
> 
> .
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com
> 
> .
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLGzZ8NYhZOBV-oos%2BmhbUAJonnDo7%3DNM-XX0xqyVBiwiA%40mail.gmail.com.

Re: Thin Stock support block dimensions

2023-02-13 Thread Tim Ziegler

I would have it but not until tomorrow for sure.

Kind Regards,

Timothy J. Ziegler
Ziegler WoodWork & Specialty
14171 160th Ave.
Foreston MN 56330

320-294-5798 shop
320-630-2243 cell


On Mon, Feb 13, 2023 at 5:20 PM Mike Newman  wrote:

> Does anyone already have the dimension for the hdpe blocks used on the
> factory thin stock support?  I finally found a block of the material that I
> can make my own, but wanted to get the dimensions.  Overall dimensions and
> then size/position of the v-notch should be all I need.  I will attach it
> to my cross member I used for my first trial design.  If anyone has one of
> the actual factory take a few measurements and post them or email me
> direct.  I can figure it out if nobody has a factory one, but thought I
> would quickly check before I go down that road?  thanks
>
> --
> You received this message because you are subscribed to the Google Groups
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
> To view this discussion on the web visit
> https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com
> 
> .
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/CAMBiJLFijhg2Sa%2ByTGTGgc0pAJpiCKRsqn45EwfDK2v4diZeXw%40mail.gmail.com.

Re: Thin Stock support block dimensions

2023-02-13 Thread Mike Newman

thanks for the info both dim/tailstock reference.  Makes perfect sense on 
using the tail stock as a reference to go with the overall dim provided by 
Denson.  
On Monday, February 13, 2023 at 6:30:36 PM UTC-6 Curt George wrote:

> Mike.
> A simple way to make your own steady rest is to make the cross members 
> first. then USING those mounted to the Legacy's rails, you can make your 
> blocks, By using your tailstock as a reference point, mark the steady 
> blocks so the center point of the tail stock is the middle of the V/ center 
> of the steady rest blocks.
>
> C.A.G.
>
> On Monday, February 13, 2023 at 06:49:27 PM EST, 'Denson Ingram' via 
> Legacy Ornamental Mills  wrote: 
>
>
> Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick
> Denson
> Sent from Denson's iPhone
>
> On Feb 13, 2023, at 5:20 PM, Mike Newman  wrote:
>
> Does anyone already have the dimension for the hdpe blocks used on the 
> factory thin stock support?  I finally found a block of the material that I 
> can make my own, but wanted to get the dimensions.  Overall dimensions and 
> then size/position of the v-notch should be all I need.  I will attach it 
> to my cross member I used for my first trial design.  If anyone has one of 
> the actual factory take a few measurements and post them or email me 
> direct.  I can figure it out if nobody has a factory one, but thought I 
> would quickly check before I go down that road?  thanks
>
> -- 
> You received this message because you are subscribed to the Google Groups 
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an 
> email to legacy-ornamental...@googlegroups.com.
> To view this discussion on the web visit 
> https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com
>  
> 
> .
>
> -- 
> You received this message because you are subscribed to the Google Groups 
> "Legacy Ornamental Mills" group.
> To unsubscribe from this group and stop receiving emails from it, send an 
> email to legacy-ornamental...@googlegroups.com.
> To view this discussion on the web visit 
>
> https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com
>  
> 
> .
>

-- 
You received this message because you are subscribed to the Google Groups 
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit 
https://groups.google.com/d/msgid/legacy-ornamental-mills/f53d11c4-bbd8-43e3-b742-6c1f2d3b4538n%40googlegroups.com.

Re: Thin Stock support block dimensions

2023-02-13 Thread 'Curt George' via Legacy Ornamental Mills

Mike.A simple way to make your own steady rest is to make the cross members
first. then USING those mounted to the Legacy's rails, you can make your
blocks, By using your tailstock as a reference point, mark the steady blocks so
the center point of the tail stock is the middle of the V/ center of the steady
rest blocks.
C.A.G.
On Monday, February 13, 2023 at 06:49:27 PM EST, 'Denson Ingram' via Legacy
Ornamental Mills wrote:

Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thick
Denson
Sent from Denson's iPhone

On Feb 13, 2023, at 5:20 PM, Mike Newman wrote:

Does anyone already have the dimension for the hdpe blocks used on the factory
thin stock support? I finally found a block of the material that I can make my
own, but wanted to get the dimensions. Overall dimensions and then
size/position of the v-notch should be all I need. I will attach it to my
cross member I used for my first trial design. If anyone has one of the actual
factory take a few measurements and post them or email me direct. I can figure
it out if nobody has a factory one, but thought I would quickly check before I
go down that road? thanks

--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com.

--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com.

--
You received this message because you are subscribed to the Google Groups
"Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit
https://groups.google.com/d/msgid/legacy-ornamental-mills/685657489.704049.1676334595002%40mail.yahoo.com.

Re: Thin Stock support block dimensions

2023-02-13 Thread 'Denson Ingram' via Legacy Ornamental Mills

Mike those pieces are 2 1/4” w x 1 1/4” L x 1 1/4” thickDensonSent from Denson's iPhoneOn Feb 13, 2023, at 5:20 PM, Mike Newman  wrote:Does anyone already have the dimension for the hdpe blocks used on the factory thin stock support?  I finally found a block of the material that I can make my own, but wanted to get the dimensions.  Overall dimensions and then size/position of the v-notch should be all I need.  I will attach it to my cross member I used for my first trial design.  If anyone has one of the actual factory take a few measurements and post them or email me direct.  I can figure it out if nobody has a factory one, but thought I would quickly check before I go down that road?  thanks



-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/d9930f81-cbb4-4da0-bd7d-bfe71e6ea51dn%40googlegroups.com.




-- 
You received this message because you are subscribed to the Google Groups "Legacy Ornamental Mills" group.
To unsubscribe from this group and stop receiving emails from it, send an email to legacy-ornamental-mills+unsubscr...@googlegroups.com.
To view this discussion on the web visit https://groups.google.com/d/msgid/legacy-ornamental-mills/ADA4C3D3-0AB3-4E75-9026-8AF9A463DFDB%40yahoo.com.

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

Re: Thin Stock support block dimensions

7 matches

Site Navigation

Mail list logo

Footer information