Re: OpenBSD on a Nokia IP380
On Sat, Aug 24, 2013 at 3:00 PM, Chris Cappuccio wrote: The errors you got are due to errors reported by the IDE controller back to the pciide driver. That's a layer (or two) lower than the filesystem itself. If moving the drive around fixed it, perhaps there was a poor connection somewhere? (Hell, I just bought an old stereo receiver and had to take it apart and reseat every board inside to clean up the sound coming out...) Since the dc driver doesn't know how to read the MAC addresses from your system, your best bet to make those work is to use the 'lladdr' flag so that something other than 0 is used on the wire... It looks like I have an intermittent connection or a controller that's going bad. When I try to get networking to work, the system hangs at starting the network. Some times it completes and I get a login prompt, other times I don't. At times it gives the same errors as I posted before. I'll experiment with the other units I have to see if the problem follows the hard drive. I noticed both the IP350 and IP380 have a MAC address label on the system board. I suspect this is the starting address used to assigned addresses to the fxp and dc interfaces. Where that address is stored is a good question. Odd that the fxp interfaces have FF and the dc interfaces have 00. I was sent a link about an Intel utility called eeupdate.exe that can be used to write the MAC address to the eeprom. But, it looks like that utility is an OEM download from Intel. It looks like one can put lladdr in the hostnam.if file and set the address that way. The 100/1000 card looks like it has the addresses onboard. I haven't tried copper SFPs to see if they will work in place of the fiber SFPs. Would be nice if they do. Thanks again to everyone for the help with this. Stan
Re: OpenBSD on a Nokia IP380
On Fri, Aug 23, 2013 at 11:06 PM, Mike Larkin wrote: At the boot prompt, what does mach mem show? -ml Hi Mike, here's the output from mach mem. It only has 1GB of memory. Not sure why it's saying the total is 2GB. Stan Using drive 0, partition 3. Loading. probing: pc0 com0 com1 pci mem[637K 1023M 1023M a20=on] disk: hd0+ OpenBSD/i386 BOOT 3.21 switching console to com0 OpenBSD/i386 BOOT 3.21 boot: illegal argument acpi boot mach mem Region 0: type 1 at 0x0 for 637KB Region 1: type 2 at 0x9f400 for 3KB Region 2: type 1 at 0x10 for 1047552KB Region 3: type 1 at 0x10 for 1047552KB Region 4: type 2 at 0xfff0 for 1024KB Low ram: 637KB High ram: 2095104KB Total free memory: 2095741KB boot $
Re: OpenBSD on a Nokia IP380
On Sat, Aug 24, 2013 at 10:08 AM, Brynet wrote: This is likely a problem with the BIOS on the system, the memory map has duplicate entries.. You can attempt to manually fix this at boot using a variation of the same command used to retreive the mappings: boot mach mem =1023M You can play around with it, maybe try removing both of the duplicates first: boot mach mem -0x3ff0@0x10 boot mach mem -0x3ff0@0x10 -Bryan. Bryan, removing both gives this warning: too little memory available;running in degraded mode press a key to confirm [ using 749064 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.3 (GENERIC) #50: Tue Mar 12 18:35:23 MDT 2013 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III (GenuineIntel 686-class) 867 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,PSN,MMX,FXSR,SSE real mem = 585728 (0MB) avail mem = 790528 (0MB) panic: procinit: malloc Stopped at Debugger+0x4: popl%ebp Debugger(d08fdcbc,d0bc9f04,d08d9e90,d0bc9f04,bc8000) at Debugger+0x4 panic(d08d9e90,29,2,d0a548c8,0) at panic+0x5d procinit(d08d6b00,d08d8f40,c0,d0bc9f4c,1) at procinit+0x29c main(d02004f6,d02004fe,0,0,0) at main+0x75 RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC! Removing only one, I get this. As you can see, all the NICs have FF and 00 as the MAC address. So, it's a bit farther, but still not quite there... Stan [ using 749064 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.3 (GENERIC) #50: Tue Mar 12 18:35:23 MDT 2013 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III (GenuineIntel 686-class) 867 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,PSN,MMX,FXSR,SSE real mem = 1073278976 (1023MB) avail mem = 1044758528 (996MB) mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 04/30/04, BIOS32 rev. 0 @ 0xe7650 pcibios0 at bios0: rev 2.1 @ 0xe76c0/0x600 pcibios0: PCI BIOS has 9 Interrupt Routing table entries pcibios0: PCI Exclusive IRQs: 5 7 9 10 11 pcibios0: PCI Interrupt Router at 000:15:0 (ServerWorks OSB4 rev 0x00) pcibios0: PCI bus #4 is the last bus cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 ServerWorks CNB20LE Host rev 0x06 pchb1 at pci0 dev 0 function 1 ServerWorks CNB20LE Host rev 0x06 pci1 at pchb1 bus 1 ppb0 at pci1 dev 0 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci2 at ppb0 bus 2 fxp0 at pci2 dev 3 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4 fxp1 at pci2 dev 4 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4 fxp2 at pci2 dev 5 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4 fxp3 at pci2 dev 6 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4 ppb1 at pci1 dev 2 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci3 at ppb1 bus 3 dc0 at pci3 dev 5 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy0 at dc0 phy 1: BCM5221 100baseTX PHY, rev. 4 dc1 at pci3 dev 6 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy1 at dc1 phy 1: BCM5221 100baseTX PHY, rev. 4 cbb0 at pci0 dev 9 function 0 TI PCI1420 CardBus rev 0x00: couldn't map interrupt cbb1 at pci0 dev 9 function 1 TI PCI1420 CardBus rev 0x00: couldn't map interrupt ubsec0 at pci0 dev 10 function 0 Broadcom 5802 rev 0x01: 3DES MD5 SHA1 RNG PK, irq 11 piixpm0 at pci0 dev 15 function 0 ServerWorks OSB4 rev 0x51: polling iic0 at piixpm0 lmenv0 at iic0 addr 0x2d: lm87 rev 6, starting scan lmenv1 at iic0 addr 0x2e: lm87 rev 6, starting scan spdmem0 at iic0 addr 0x50: 512MB SDRAM registered ECC PC133CL2 spdmem1 at iic0 addr 0x51: 512MB SDRAM registered ECC PC133CL2 pciide0 at pci0 dev 15 function 1 ServerWorks OSB4 IDE rev 0x00: DMA wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2040AS wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 ohci0 at pci0 dev 15 function 2 ServerWorks OSB4/CSB5 USB rev 0x04: irq 11, version 1.0, legacy support DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!
Re: OpenBSD on a Nokia IP380
On Sat, Aug 24, 2013 at 11:00 AM, Brynet wrote: z I meant removing both mappings and then adding a single 1023M mapping, I didn't expect it to work with 1M of RAM. ;-) I figured that out after the fact :) What is the new panic message? Does it enter ddb? The bogus MAC addresses could indicate a problem, but it's possible there is no EPROM defaults.. once you boot successfully you can configure your it manually with ifconfig int lladdr xx:xx:xx:xx:xx:xx. You mentioned problems with USB on FreeBSD, so try disabling ohci(4) in UKC and see if that helps (..remember to fix the mappings): boot boot -c .. ukc disable ohci ukc quit -Bryan. No, it hung and didn't enter ddb. I accidentally copied that last line. Here's the latest attempt. It went into the la la land at this point. Gotta run. Thanks for the help. Talk to you later Stan Using drive 0, partition 3. Loading. probing: pc0 com0 com1 pci mem[637K 1023M 1023M a20=on] disk: hd0+ OpenBSD/i386 BOOT 3.21 -switching console to com0 OpenBSD/i386 BOOT 3.21 boot mach mem -0x3ff0@0x10 Region 0: type 1 at 0x0 for 637KB Region 1: type 2 at 0x9f400 for 3KB Region 2: type 1 at 0x10 for 1047552KB Region 3: type 2 at 0xfff0 for 1024KB Low ram: 637KB High ram: 2095104KB Total free memory: 1048189KB boot boot -c booting hd0a:/bsd: 8404228+1102404 [52+381152+367486]=0x9c7d50 entry point at 0x200120 [ using 749064 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.3 (GENERIC) #50: Tue Mar 12 18:35:23 MDT 2013 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III (GenuineIntel 686-class) 867 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,PSN,MMX,FXSR,SSE real mem = 1073278976 (1023MB) avail mem = 1044758528 (996MB) User Kernel Config UKC disable ohci 154 ohci* disabled 155 ohci* disabled UKC quit Continuing... mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 04/30/04, BIOS32 rev. 0 @ 0xe7650 pcibios0 at bios0: rev 2.1 @ 0xe76c0/0x600 pcibios0: PCI BIOS has 9 Interrupt Routing table entries pcibios0: PCI Exclusive IRQs: 5 7 9 10 11 pcibios0: PCI Interrupt Router at 000:15:0 (ServerWorks OSB4 rev 0x00) pcibios0: PCI bus #4 is the last bus cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 ServerWorks CNB20LE Host rev 0x06 pchb1 at pci0 dev 0 function 1 ServerWorks CNB20LE Host rev 0x06 pci1 at pchb1 bus 1 ppb0 at pci1 dev 0 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci2 at ppb0 bus 2 fxp0 at pci2 dev 3 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4 fxp1 at pci2 dev 4 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4 fxp2 at pci2 dev 5 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4 fxp3 at pci2 dev 6 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4 ppb1 at pci1 dev 2 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci3 at ppb1 bus 3 dc0 at pci3 dev 5 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy0 at dc0 phy 1: BCM5221 100baseTX PHY, rev. 4 dc1 at pci3 dev 6 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy1 at dc1 phy 1: BCM5221 100baseTX PHY, rev. 4 cbb0 at pci0 dev 9 function 0 TI PCI1420 CardBus rev 0x00: couldn't map interrupt cbb1 at pci0 dev 9 function 1 TI PCI1420 CardBus rev 0x00: couldn't map interrupt ubsec0 at pci0 dev 10 function 0 Broadcom 5802 rev 0x01: 3DES MD5 SHA1 RNG PK, irq 11 piixpm0 at pci0 dev 15 function 0 ServerWorks OSB4 rev 0x51: polling iic0 at piixpm0 lmenv0 at iic0 addr 0x2d: lm87 rev 6, starting scan lmenv1 at iic0 addr 0x2e: lm87 rev 6, starting scan spdmem0 at iic0 addr 0x50: 512MB SDRAM registered ECC PC133CL2 spdmem1 at iic0 addr 0x51: 512MB SDRAM registered ECC PC133CL2 pciide0 at pci0 dev 15 function 1 ServerWorks OSB4 IDE rev 0x00: DMA wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2040AS wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 ServerWorks OSB4/CSB5 USB rev 0x04 at pci0 dev 15 function 2 not configured isa0 at mainbus0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com0: console com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 mtrr: Pentium Pro MTRR support vscsi0
Re: OpenBSD on a Nokia IP380
I finally got it to boot successfully. Not sure what was up with the hard drive errors. Maybe the file system wasn't clean? After I put the drive in the laptop and let it boot Ok, it's been booting Ok in the IP380. I'll see if I can get the network ports to work later today. Thanks again for all the help! Stan [ using 749064 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org OpenBSD 5.3 (GENERIC) #50: Tue Mar 12 18:35:23 MDT 2013 dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III (GenuineIntel 686-class) 867 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,PSN,MMX,FXSR,SSE real mem = 1073278976 (1023MB) avail mem = 1044758528 (996MB) User Kernel Config UKC disable ohci 154 ohci* disabled 155 ohci* disabled UKC quit Continuing... mainbus0 at root bios0 at mainbus0: AT/286+ BIOS, date 04/30/04, BIOS32 rev. 0 @ 0xe7650 pcibios0 at bios0: rev 2.1 @ 0xe76c0/0x600 pcibios0: PCI BIOS has 9 Interrupt Routing table entries pcibios0: PCI Exclusive IRQs: 5 7 9 10 11 pcibios0: PCI Interrupt Router at 000:15:0 (ServerWorks OSB4 rev 0x00) pcibios0: PCI bus #4 is the last bus cpu0 at mainbus0: (uniprocessor) pci0 at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function 0 ServerWorks CNB20LE Host rev 0x06 pchb1 at pci0 dev 0 function 1 ServerWorks CNB20LE Host rev 0x06 pci1 at pchb1 bus 1 ppb0 at pci1 dev 0 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci2 at ppb0 bus 2 fxp0 at pci2 dev 3 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4 fxp1 at pci2 dev 4 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4 fxp2 at pci2 dev 5 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4 fxp3 at pci2 dev 6 function 0 Intel 82559ER rev 0x10, i82551: irq 11, address ff:ff:ff:ff:ff:ff inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4 ppb1 at pci1 dev 2 function 0 Intel 21154AE/BE PCI-PCI rev 0x00 pci3 at ppb1 bus 3 dc0 at pci3 dev 5 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy0 at dc0 phy 1: BCM5221 100baseTX PHY, rev. 4 dc1 at pci3 dev 6 function 0 DEC 21142/3 rev 0x41: irq 10, address 00:00:00:00:00:00 bmtphy1 at dc1 phy 1: BCM5221 100baseTX PHY, rev. 4 cbb0 at pci0 dev 9 function 0 TI PCI1420 CardBus rev 0x00: couldn't map interrupt cbb1 at pci0 dev 9 function 1 TI PCI1420 CardBus rev 0x00: couldn't map interrupt ubsec0 at pci0 dev 10 function 0 Broadcom 5802 rev 0x01: 3DES MD5 SHA1 RNG PK, irq 11 piixpm0 at pci0 dev 15 function 0 ServerWorks OSB4 rev 0x51: polling iic0 at piixpm0 lmenv0 at iic0 addr 0x2d: lm87 rev 6 lmenv1 at iic0 addr 0x2e: lm87 rev 6 spdmem0 at iic0 addr 0x50: 512MB SDRAM registered ECC PC133CL2 spdmem1 at iic0 addr 0x51: 512MB SDRAM registered ECC PC133CL2 pciide0 at pci0 dev 15 function 1 ServerWorks OSB4 IDE rev 0x00: DMA wd0 at pciide0 channel 0 drive 0: FUJITSU MHT2040AS wd0: 16-sector PIO, LBA, 38154MB, 78140160 sectors wd0(pciide0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 2 ServerWorks OSB4/CSB5 USB rev 0x04 at pci0 dev 15 function 2 not configured isa0 at mainbus0 isadma0 at isa0 com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo com0: console com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard pcppi0 at isa0 port 0x61 spkr0 at pcppi0 npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 mtrr: Pentium Pro MTRR support vscsi0 at root scsibus0 at vscsi0: 256 targets softraid0 at root scsibus1 at softraid0: 256 targets root on wd0a (f6446c169da91933.a) swap on wd0b dump on wd0b Automatic boot in progress: starting file system checks. /dev/rwd0a: file system is clean; not checking /dev/rwd0k: file system is clean; not checking /dev/rwd0d: file system is clean; not checking /dev/rwd0f: file system is clean; not checking /dev/rwd0g: file system is clean; not checking /dev/rwd0h: file system is clean; not checking /dev/rwd0j: file system is clean; not checking /dev/rwd0i: file system is clean; not checking /dev/rwd0e: file system is clean; not checking setting tty flags pf enabled starting network starting early daemons: syslogd pflogd. starting RPC daemons:. savecore: no core dump checking quotas: done. clearing /tmp starting pre-securelevel daemons:. setting kernel security level: kern.securelevel: 0 - 1 creating runtime link editor directory cache. preserving editor files. starting network daemons: sendmail inetd sndiod. starting local daemons: cron. Sat Aug 24 09:30:40 CDT 2013 OpenBSD/i386 (gateway.home.pc) (tty00)
OpenBSD on a Nokia IP380
I've been trying to get a more modern OS to run on an ancient Nokia firewall by loading an OS on the drive in a Dell D610 and moving the drive to the IP380. So far, I've had little success. I can get FreeBSD 8.1 to work if I disable USB support. That's the only OS I've been able to get to boot somewhat normally and I'm able to login with it. All of the NIC cards have all FFs for the MAC address though. SO, I decided to try OpenBSD 5.3 RELEASE and I've been unable to get it to boot. Below is the output. I tried disabling ACPI in a similar fashion to FreeBSD and found that didn't work. I guess removing ACPI and USB from a pre-built kernel is the next step. Other than giving up and tossing the ancient firewall on the recycle pile, does anyone have any ideas on how to get OpenBSD to work on the IP380? Or what's causing it to crash? Stan +--+ | System BIOS Configuration, (C) 2000 General Software, Inc. | +---+--+ | System CPU : Pentium III| Low Memory : 637KB | | Coprocessor : Enabled| Extended Memory : 1023MB | | Floppy 0 Type: Not installed | Serial Ports 1-2 : 03F8 02F8 | | Floppy 1 Type: Not installed | Serial Ports 3-4 : | | Ide 0 Type : 3 | Parallel Ports : | | Ide 1 Type : 0 | ROM Shadowing: Enabled | | Embedded BIOS Date : 04/30/04 | Manufacturing Mode : Disabled | +---+--+ Using drive 0, partition 3. Loading. probing: pc0 com0 com1 pci mem[637K 1023M 1023M a20=on] disk: hd0+ OpenBSD/i386 BOOT 3.21 switching console to com0 OpenBSD/i386 BOOT 3.21 boot: illegal argument acpi boot boot booting hd0a:/bsd: 8404228+1102404 [52+381152+367486]=0x9c7d50 entry point at 0x200120 WARNING: CAN'T ALLOCATE RAM (10-4000) FROM IOMEM EXTENT MAP! [ using 749064 bytes of bsd ELF symbol table ] Copyright (c) 1982, 1986, 1989, 1991, 1993 The Regents of the University of California. All rights reserved. Copyright (c) 1995-2013 OpenBSD. All rights reserved. http://www.OpenBSD.org kernel: page fault trap, code=0 Stopped at pmap_alloc_pvpage+0x2d: movl%ecx,0(%eax) pmap_alloc_pvpage(d0a7f580,0,6d54000,0,0) at pmap_alloc_pvpage+0x2d pmap_enter(d0a7f580,d6d54000,3ffdb000,7,13) at pmap_enter+0x340 uvm_km_alloc1(d0a2dd40,1,0,1,2) at uvm_km_alloc1+0xd2 kmeminit(d2d53000,ffc0,bebc9f28,bca000,bc8000) at kmeminit+0x95 uvm_init(d08d6b00,d08d8f40,c0,d0bc9f4c,3) at uvm_init+0x51 main(d02004f6,d02004fe,0,0,0) at main+0x53 ddb trace pmap_alloc_pvpage(d0a7f580,0,6d54000,0,0) at pmap_alloc_pvpage+0x2d pmap_enter(d0a7f580,d6d54000,3ffdb000,7,13) at pmap_enter+0x340 uvm_km_alloc1(d0a2dd40,1,0,1,2) at uvm_km_alloc1+0xd2 kmeminit(d2d53000,ffc0,bebc9f28,bca000,bc8000) at kmeminit+0x95 uvm_init(d08d6b00,d08d8f40,c0,d0bc9f4c,3) at uvm_init+0x51 main(d02004f6,d02004fe,0,0,0) at main+0x53
Re: OpenBSD on a Nokia IP380
On Fri, Aug 23, 2013 at 6:04 PM, Ray Percival wrote: Having worked for Check Point/Nokia. They wine to great lengths to only make that hardware work with their Free based OS. I wish you luck but realistically it's not likely. OpenBSD works just fine on the newer Check Point boxes. They're far less locked down. Hi Ray, I was afraid of that. I've yet to figure out why FreeBSD 8.1 will somewhat work but nothing newer works. Anything newer crashes. I've had limited success with Fedora 19 too. It just takes forever to build a custom Linux kernel on the machine I'm building it on. Building a BSD kernel takes about 30 minutes on that machine. Perhaps you have the answer to something I suspect is the case. I'm guessing the MAC address on the system board is the starting MAC address and the MAC addresses for the NICs are assigned during boot based on the starting address? Thanks for the reply. Stan
