RE: RE: XCP-NG 8.2 LTS
Its on my to-do list to update it. Best regards, Jordan -Original Message- From: Jermaine Kendall Sent: Friday, June 25, 2021 11:46 PM To: users@cloudstack.apache.org Subject: Re: RE: XCP-NG 8.2 LTS [X] This message came from outside your organization Thank you for the reply. It is very much appreciated. Can the documentation be upgraded for XCP-NG hypervisor setup and let me know it's done On 2021/06/25 20:33:08, Yordan Kostov wrote: > Hello Jermaine, > > Long story short: > 1. Install XCP-NG 8.2 > 1.1. Make a a note of the name of the interface OR bond that is > going to be used for management traffic (this can be seen when you go to > CLUSTER -> networking tab > 1.2. Make a note of the name of the interface OR bond that is > going to be used for user/public traffic if it is different then the > management > For example I use ETH0 for management and have bonded eth2 and eth3 and > use that bond for Public and user traffic - > https://urldefense.com/v3/__https://imgur.com/nbV2aAu__;!!A6UyJA!wDUMW6z5oiy9Dn5sjnQg0lEHza62apzb8T-x4oNAB42Sh99wLL6e3w9RjmN59FNHoLQ2vcyqdMZ2$ > So the labels here are MGMT and DATA. > 2. If you use presetup storage (for example fiber) attach it as you > usually do to the XCP cluster and note the name of the LUN in XenCenter. > 3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up > the guide from start to end using the interface labels and the LUN name for > primary storage. > 4. Launch the zone deployment and wait for it to fail. > 5. Cancel the wizard and go to Infrastruture tab. You will see that > Zone, Pod, cluster and hosts are deployed. > 6. select primary storage tab. Add new one with presetup type and fill > in the storage LUN name. It will be added properly. > 7. Deploy secondary storage (it was not deployed initially > because the zone wizard was interrupted before that step) > > You environment is now ready! > > Note: the deployment guide should be edited as it says XenServer switch > needs to be in bridge mode in order the system to work which is not correct > as ACS fully supports OVS. > May be bridge mode is required for some specific network design setting > which I am not aware of at the moment. > > Best regards, > Jordan > > > -Original Message----- > From: Jermaine Kendall > Sent: Friday, June 25, 2021 10:49 PM > To: users@cloudstack.apache.org > Subject: Re: XCP-NG 8.2 LTS > > > [X] This message came from outside your organization > > > On 2021/05/05 09:50:58, Andrija Panic wrote: > > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), > > you will be missing the records in the guest_os_hypervisor table, > > and that means your VMs would be i.e. started as PV instead of HVM etc. > > > > Be warned :) > > > > Best, > > Andrija > > > > On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote: > > > > > One more problem is that if you deploy a zone with presetup > > > storage it will give an error when it is at the step when the storage is > > > configured. > > > It is already fixed in 4.15.1: > > > > > > https://urldefense.com/v3/__https://github.com/apache/cloudstack/p > > > ul > > > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQ > > > Oh > > > yt15t8yi-mQoUBNEaGjZ6RgICA$ > > > > > > Best regards, > > > Jordan > > > > > > -Original Message- > > > From: Dominik Czerepiński > > > Sent: Tuesday, May 4, 2021 3:06 PM > > > To: users@cloudstack.apache.org > > > Subject: Re: XCP-NG 8.2 LTS > > > > > > > > > [X] This message came from outside your organization > > > > > > > > > Me. Works stable. One problem is if You don’t use SSL for > > > consoleproxy change noVNC to older version. > > > > > > Wysłane z iPhone'a > > > > > > > Wiadomość napisana przez Matheus Fontes w > > > > dniu > > > 04.05.2021, o godz. 03:18: > > > > > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng > > > > 8.1 Does someone tried 8.2 LTS version? > > > > > > > > thanks > > > > Matheus Fontes > > > > > > > > > -- > > > > Andrija Panić > > Hi, I have a few questions with regard to setting up xcp-ng with > > cloudstack, I have never been successful so far. I followed the xenserver > > hypervisor setup and ran into some issues. Do you have any instructions > > specifically for setting up XCP-NG with cloudstack? Also is the CSP package > > needed for XCP-NG becuase the download link is no longer available. The > > network labels, are they necessary and why can't I use the default > > networking for XCP-NG which is OVS? >
Re: RE: XCP-NG 8.2 LTS
Thank you for the reply. It is very much appreciated. Can the documentation be upgraded for XCP-NG hypervisor setup and let me know it's done On 2021/06/25 20:33:08, Yordan Kostov wrote: > Hello Jermaine, > > Long story short: > 1. Install XCP-NG 8.2 > 1.1. Make a a note of the name of the interface OR bond that is > going to be used for management traffic (this can be seen when you go to > CLUSTER -> networking tab > 1.2. Make a note of the name of the interface OR bond that is > going to be used for user/public traffic if it is different then the > management > For example I use ETH0 for management and have bonded eth2 and eth3 and > use that bond for Public and user traffic - https://imgur.com/nbV2aAu > So the labels here are MGMT and DATA. > 2. If you use presetup storage (for example fiber) attach it as you > usually do to the XCP cluster and note the name of the LUN in XenCenter. > 3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up > the guide from start to end using the interface labels and the LUN name for > primary storage. > 4. Launch the zone deployment and wait for it to fail. > 5. Cancel the wizard and go to Infrastruture tab. You will see that > Zone, Pod, cluster and hosts are deployed. > 6. select primary storage tab. Add new one with presetup type and fill > in the storage LUN name. It will be added properly. > 7. Deploy secondary storage (it was not deployed initially because the > zone wizard was interrupted before that step) > > You environment is now ready! > > Note: the deployment guide should be edited as it says XenServer switch > needs to be in bridge mode in order the system to work which is not correct > as ACS fully supports OVS. > May be bridge mode is required for some specific network design setting > which I am not aware of at the moment. > > Best regards, > Jordan > > > -Original Message----- > From: Jermaine Kendall > Sent: Friday, June 25, 2021 10:49 PM > To: users@cloudstack.apache.org > Subject: Re: XCP-NG 8.2 LTS > > > [X] This message came from outside your organization > > > On 2021/05/05 09:50:58, Andrija Panic wrote: > > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), > > you will be missing the records in the guest_os_hypervisor table, and > > that means your VMs would be i.e. started as PV instead of HVM etc. > > > > Be warned :) > > > > Best, > > Andrija > > > > On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote: > > > > > One more problem is that if you deploy a zone with presetup storage > > > it will give an error when it is at the step when the storage is > > > configured. > > > It is already fixed in 4.15.1: > > > > > > https://urldefense.com/v3/__https://github.com/apache/cloudstack/pul > > > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQOh > > > yt15t8yi-mQoUBNEaGjZ6RgICA$ > > > > > > Best regards, > > > Jordan > > > > > > -Original Message- > > > From: Dominik Czerepiński > > > Sent: Tuesday, May 4, 2021 3:06 PM > > > To: users@cloudstack.apache.org > > > Subject: Re: XCP-NG 8.2 LTS > > > > > > > > > [X] This message came from outside your organization > > > > > > > > > Me. Works stable. One problem is if You don’t use SSL for > > > consoleproxy change noVNC to older version. > > > > > > Wysłane z iPhone'a > > > > > > > Wiadomość napisana przez Matheus Fontes w > > > > dniu > > > 04.05.2021, o godz. 03:18: > > > > > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng > > > > 8.1 Does someone tried 8.2 LTS version? > > > > > > > > thanks > > > > Matheus Fontes > > > > > > > > > -- > > > > Andrija Panić > > Hi, I have a few questions with regard to setting up xcp-ng with > > cloudstack, I have never been successful so far. I followed the xenserver > > hypervisor setup and ran into some issues. Do you have any instructions > > specifically for setting up XCP-NG with cloudstack? Also is the CSP package > > needed for XCP-NG becuase the download link is no longer available. The > > network labels, are they necessary and why can't I use the default > > networking for XCP-NG which is OVS? >
RE: XCP-NG 8.2 LTS
Hello Jermaine, Long story short: 1. Install XCP-NG 8.2 1.1. Make a a note of the name of the interface OR bond that is going to be used for management traffic (this can be seen when you go to CLUSTER -> networking tab 1.2. Make a note of the name of the interface OR bond that is going to be used for user/public traffic if it is different then the management For example I use ETH0 for management and have bonded eth2 and eth3 and use that bond for Public and user traffic - https://imgur.com/nbV2aAu So the labels here are MGMT and DATA. 2. If you use presetup storage (for example fiber) attach it as you usually do to the XCP cluster and note the name of the LUN in XenCenter. 3. Install Cloudstack somewhere (4.15) and deploy a zone by filling up the guide from start to end using the interface labels and the LUN name for primary storage. 4. Launch the zone deployment and wait for it to fail. 5. Cancel the wizard and go to Infrastruture tab. You will see that Zone, Pod, cluster and hosts are deployed. 6. select primary storage tab. Add new one with presetup type and fill in the storage LUN name. It will be added properly. 7. Deploy secondary storage (it was not deployed initially because the zone wizard was interrupted before that step) You environment is now ready! Note: the deployment guide should be edited as it says XenServer switch needs to be in bridge mode in order the system to work which is not correct as ACS fully supports OVS. May be bridge mode is required for some specific network design setting which I am not aware of at the moment. Best regards, Jordan -Original Message- From: Jermaine Kendall Sent: Friday, June 25, 2021 10:49 PM To: users@cloudstack.apache.org Subject: Re: XCP-NG 8.2 LTS [X] This message came from outside your organization On 2021/05/05 09:50:58, Andrija Panic wrote: > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), > you will be missing the records in the guest_os_hypervisor table, and > that means your VMs would be i.e. started as PV instead of HVM etc. > > Be warned :) > > Best, > Andrija > > On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote: > > > One more problem is that if you deploy a zone with presetup storage > > it will give an error when it is at the step when the storage is configured. > > It is already fixed in 4.15.1: > > > > https://urldefense.com/v3/__https://github.com/apache/cloudstack/pul > > l/4845__;!!A6UyJA!xbgZNCFeV-go7cGrUjQ---_MlaAER2Fdumg-cMdW4msQVKLQOh > > yt15t8yi-mQoUBNEaGjZ6RgICA$ > > > > Best regards, > > Jordan > > > > -Original Message- > > From: Dominik Czerepiński > > Sent: Tuesday, May 4, 2021 3:06 PM > > To: users@cloudstack.apache.org > > Subject: Re: XCP-NG 8.2 LTS > > > > > > [X] This message came from outside your organization > > > > > > Me. Works stable. One problem is if You don’t use SSL for > > consoleproxy change noVNC to older version. > > > > Wysłane z iPhone'a > > > > > Wiadomość napisana przez Matheus Fontes w > > > dniu > > 04.05.2021, o godz. 03:18: > > > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng > > > 8.1 Does someone tried 8.2 LTS version? > > > > > > thanks > > > Matheus Fontes > > > > > -- > > Andrija Panić > Hi, I have a few questions with regard to setting up xcp-ng with cloudstack, > I have never been successful so far. I followed the xenserver hypervisor > setup and ran into some issues. Do you have any instructions specifically for > setting up XCP-NG with cloudstack? Also is the CSP package needed for XCP-NG > becuase the download link is no longer available. The network labels, are > they necessary and why can't I use the default networking for XCP-NG which is > OVS?
Re: XCP-NG 8.2 LTS
On 2021/05/05 09:50:58, Andrija Panic wrote: > If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), you > will be missing the records in the guest_os_hypervisor table, and that > means your VMs would be i.e. started as PV instead of HVM etc. > > Be warned :) > > Best, > Andrija > > On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote: > > > One more problem is that if you deploy a zone with presetup storage it > > will give an error when it is at the step when the storage is configured. > > It is already fixed in 4.15.1: > > > > https://github.com/apache/cloudstack/pull/4845 > > > > Best regards, > > Jordan > > > > -Original Message- > > From: Dominik Czerepiński > > Sent: Tuesday, May 4, 2021 3:06 PM > > To: users@cloudstack.apache.org > > Subject: Re: XCP-NG 8.2 LTS > > > > > > [X] This message came from outside your organization > > > > > > Me. Works stable. One problem is if You don’t use SSL for consoleproxy > > change noVNC to older version. > > > > Wysłane z iPhone'a > > > > > Wiadomość napisana przez Matheus Fontes w dniu > > 04.05.2021, o godz. 03:18: > > > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 > > > Does someone tried 8.2 LTS version? > > > > > > thanks > > > Matheus Fontes > > > > > -- > > Andrija Panić > Hi, I have a few questions with regard to setting up xcp-ng with cloudstack, > I have never been successful so far. I followed the xenserver hypervisor > setup and ran into some issues. Do you have any instructions specifically for > setting up XCP-NG with cloudstack? Also is the CSP package needed for XCP-NG > becuase the download link is no longer available. The network labels, are > they necessary and why can't I use the default networking for XCP-NG which is > OVS?
Re: XCP-NG 8.2 LTS
If you use officially unsupported hypevisor with 4.14 (XCP-ng 8.2), you will be missing the records in the guest_os_hypervisor table, and that means your VMs would be i.e. started as PV instead of HVM etc. Be warned :) Best, Andrija On Wed, 5 May 2021 at 09:09, Yordan Kostov wrote: > One more problem is that if you deploy a zone with presetup storage it > will give an error when it is at the step when the storage is configured. > It is already fixed in 4.15.1: > > https://github.com/apache/cloudstack/pull/4845 > > Best regards, > Jordan > > -Original Message- > From: Dominik Czerepiński > Sent: Tuesday, May 4, 2021 3:06 PM > To: users@cloudstack.apache.org > Subject: Re: XCP-NG 8.2 LTS > > > [X] This message came from outside your organization > > > Me. Works stable. One problem is if You don’t use SSL for consoleproxy > change noVNC to older version. > > Wysłane z iPhone'a > > > Wiadomość napisana przez Matheus Fontes w dniu > 04.05.2021, o godz. 03:18: > > > > I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 > > Does someone tried 8.2 LTS version? > > > > thanks > > Matheus Fontes > -- Andrija Panić
RE: XCP-NG 8.2 LTS
One more problem is that if you deploy a zone with presetup storage it will give an error when it is at the step when the storage is configured. It is already fixed in 4.15.1: https://github.com/apache/cloudstack/pull/4845 Best regards, Jordan -Original Message- From: Dominik Czerepiński Sent: Tuesday, May 4, 2021 3:06 PM To: users@cloudstack.apache.org Subject: Re: XCP-NG 8.2 LTS [X] This message came from outside your organization Me. Works stable. One problem is if You don’t use SSL for consoleproxy change noVNC to older version. Wysłane z iPhone'a > Wiadomość napisana przez Matheus Fontes w dniu > 04.05.2021, o godz. 03:18: > > I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 > Does someone tried 8.2 LTS version? > > thanks > Matheus Fontes
Re: XCP-NG 8.2 LTS
Me. Works stable. One problem is if You don’t use SSL for consoleproxy change noVNC to older version. Wysłane z iPhone'a > Wiadomość napisana przez Matheus Fontes w dniu > 04.05.2021, o godz. 03:18: > > I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 > Does someone tried 8.2 LTS version? > > thanks > Matheus Fontes
Re: XCP-NG 8.2 LTS
YES it works Le 04/05/2021 à 03:18, Matheus Fontes a écrit : I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 Does someone tried 8.2 LTS version? thanks Matheus Fontes
Re: XCP-NG 8.2 LTS
XCP-ng 8.2/lts support has been added towards the 4.15.1.0 milestone [1]. The 4.15.0.0 release only supports XCP-ng 8.0, 8.1, the next 4.15.1.0 release will include support for version 8.2. [1] https://github.com/apache/cloudstack/pull/4672 Regards. From: Matheus Fontes Sent: Tuesday, May 4, 2021 06:48 To: users@cloudstack.apache.org Subject: XCP-NG 8.2 LTS I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 Does someone tried 8.2 LTS version? thanks Matheus Fontes
RE: XCP-NG 8.2 LTS
Hi I have ACS 4.14.1 with XCP-NG 8.2 and PreSetup iSCSI storage Now I'm testing this configuration - it works pretty good) -Original Message- From: Matheus Fontes [mailto:math...@ghz.com.br] Sent: Tuesday, May 4, 2021 4:18 AM To: users@cloudstack.apache.org Subject: XCP-NG 8.2 LTS I saw in cloudstack 4.15 documentation that it supports xcp-ng 8.1 Does someone tried 8.2 LTS version? thanks Matheus Fontes Внимание! Это электронное письмо и все прикрепленные к нему файлы являются конфиденциальными и предназначены исключительно для использования лицом (лицами), которому (которым) оно предназначено. Если Вы не являетесь лицом (лицами), которому (которым) предназначено это письмо, не копируйте и не разглашайте его содержимое и удалите это сообщение и все вложения из Вашей почтовой системы. Любое несанкционированное использование, распространение, раскрытие, печать или копирование этого электронного письма и прикрепленных к нему файлов, кроме как лицом (лицами) которому (которым) они предназначены, является незаконным и запрещено. Принимая во внимание, что передача данных посредством Интернет не является безопасной, мы не несем никакой ответственности за любой потенциальный ущерб, причиненный в результате ошибок при передаче данных или этим сообщением и прикрепленными к нему файлами. Attention! This email and all attachments to it are confidential and are intended solely for use by the person (or persons) referred to (mentioned) as the intended recipient (recipients). If you are not the intended recipient of this email, do not copy or disclose its contents and delete the message and any attachments to it from your e-mail system. Any unauthorized use, dissemination, disclosure, printing or copying of this e-mail and files attached to it, except by the intended recipient, is illegal and is prohibited. Taking into account that data transmission via Internet is not secure, we assume no responsibility for any potential damage caused by data transmission errors or this message and the files attached to it.