subject:"\[wsjt\-devel\] FT450D is missing"

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Andras Bato

Thank you so much Marco!
I have saved your message.
Michael advised me something similar with the ending -v
gl
nn


On Mon, Dec 21, 2020 at 3:08 PM Marco Calistri  wrote:

> Andras,
>
> You can dig into get more details/information *out of WSJT-X* to verify
> your hamlib and your interfaces settings/responses from your
> console/command prompt:
>
> /usr/bin/rigctld -m 1021(¹) -r /dev/FT-100_USB1(²) -p /dev/FT-100_USB0(³)
> -t 4532 -s 4800 -v
>
> (¹) = The model of your radio, *for you is 1027*!
>
> (²)=The serial interface you use for CAT interface
>
> (³)= The serial interface you use for your PTT (if any)
>
> *More details: /usr/bin/rigctld -h*
>
> marco@linux-turion64:~> rigctld -h
>
> Usage: rigctld [OPTION]...
>
> Daemon serving COMMANDs to a connected radio transceiver or receiver.
>
>   -m, --model=IDselect radio model number. See model list
>
>   -r, --rig-file=DEVICE set device of the radio to operate on
>
>   -p, --ptt-file=DEVICE set device of the PTT device to operate on
>
>   -d, --dcd-file=DEVICE set device of the DCD device to operate on
>
>   -P, --ptt-type=TYPE   set type of the PTT device to operate on
>
>   -D, --dcd-type=TYPE   set type of the DCD device to operate on
>
>   -s, --serial-speed=BAUD   set serial speed of the serial port
>
>   -c, --civaddr=ID  set CI-V address, decimal (for Icom rigs only)
>
>   -t, --port=NUMset TCP listening port, default 4532
>
>   -T, --listen-addr=IPADDR  set listening IP address, default ANY
>
>   -C, --set-conf=PARM=VAL   set config parameters
>
>   -L, --show-conf   list all config parameters
>
>   -l, --listlist all model numbers and exit
>
>   -u, --dump-caps   dump capabilities and exit
>
>   -o, --vfo do not default to VFO_CURR, require extra vfo 
> arg
>
>   -v, --verbose set verbose mode, cumulative (-v to -v)
>
>   -W, --twiddle_timeout timeout after detecting vfo manual change
>
>   -x, --uplink  set uplink get_freq ignore, 1=Sub, 2=Main
>
>   -Z, --debug-time-stamps   enable time stamps for debug messages
>
>   -h, --helpdisplay this help and exit
>
>   -V, --version output version information and exit
>
> Commands (some may not be available for this rig):
>
> F: set_freq(Frequency) f: get_freq()
>
> M: set_mode(Mode,Passband) m: get_mode()
>
> I: set_split_freq  (TX Frequency)  i: get_split_freq  ()
>
> X: set_split_mode  (TX Mode,TX Passband) x: get_split_mode  ()
>
> K: set_split_freq_mode(TX Frequency,TX Mode,TX Passband)  k: 
> get_split_freq_mode()
>
> S: set_split_vfo   (Split,TX VFO)  s: get_split_vfo   ()
>
> N: set_ts  (Tuning Step)   n: get_ts  ()
>
> L: set_level   (Level,Level Value) l: get_level   (Level)
>
> U: set_func(Func,Func Status)  u: get_func(Func)
>
> P: set_parm(Parm,Parm Value)   p: get_parm(Parm)
>
> G: vfo_op  (Mem/VFO Op)g: scan(Scan Fct,Scan 
> Channel)
>
> A: set_trn (Transceive)a: get_trn ()
>
> R: set_rptr_shift  (Rptr Shift)r: get_rptr_shift  ()
>
> O: set_rptr_offs   (Rptr Offset)   o: get_rptr_offs   ()
>
> C: set_ctcss_tone  (CTCSS Tone)c: get_ctcss_tone  ()
>
> D: set_dcs_code(DCS Code)  d: get_dcs_code()
>
> ?: set_ctcss_sql   (CTCSS Sql) ?: get_ctcss_sql   ()
>
> ?: set_dcs_sql (DCS Sql)   ?: get_dcs_sql ()
>
> V: set_vfo (VFO)   v: get_vfo ()
>
> T: set_ptt (PTT)   t: get_ptt ()
>
> E: set_mem (Memory#)   e: get_mem ()
>
> H: set_channel (Channel)   h: get_channel (Channel,Read Only)
>
> B: set_bank(Bank)  _: get_info()
>
> J: set_rit (RIT)   j: get_rit ()
>
> Z: set_xit (XIT)   z: get_xit ()
>
> Y: set_ant (Antenna,Option)y: get_ant (AntCurr)
>
> ?: set_powerstat   (Power Status)  ?: get_powerstat   ()
>
> ?: send_dtmf   (Digits)?: recv_dtmf   ()
>
> *: reset   (Reset) w: send_cmd(Cmd)
>
> W: send_cmd_rx (Cmd,Reply) b: send_morse  (Morse)
>
> ?: stop_morse  ()  ?: wait_morse  ()
>
> ?: send_voice_mem  (Voice Mem#)?: get_dcd ()
>
> ?: set_twiddle (Timeout (secs))?: get_twiddle ()
>
> ?: uplink  (1=Sub, 2=Main) ?: set_cache   (Timeout (msecs))
>
> ?: get_cache   ()  2: power2mW(Power 
> [0.0..1.0],Frequency,Mode)
>
> 4: mW2power(Pwr mW,Freq,Mode)  1: dump_caps   ()
>
> 3: dump_conf   ()  ?: dump_state  ()
>
> ?: chk_vfo

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Marco Calistri


YEP!

Il 21/12/20 11:09, Black Michael ha scritto:

I'm working with him

Mike W9MDB




On Monday, December 21, 2020, 08:08:45 AM CST, Marco Calistri 
 wrote:



Andras,

You can dig into get more details/information _out of WSJT-X_ to 
verify your hamlib and your interfaces settings/responses from your 
console/command prompt:


/usr/bin/rigctld -m 1021(¹) -r /dev/FT-100_USB1(²) -p 
/dev/FT-100_USB0(³) -t 4532 -s 4800 -v


(¹) = The model of your radio, *for you is 1027*!

(²)=The serial interface you use for CAT interface

(³)= The serial interface you use for your PTT (if any)

_More details: /usr/bin/rigctld -h_


--
Marco Calistri
Build: openSUSE Tumbleweed 20201216
Kernel:5.9.14-1-default
Desktop: XFCE (4.14.2)



___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Marco Calistri


  
Andras,
  
  You can dig into get more details/information out of WSJT-X
  to verify your hamlib and your interfaces settings/responses from
  your console/command prompt:
  
  /usr/bin/rigctld -m 1021(¹) -r /dev/FT-100_USB1(²)
-p /dev/FT-100_USB0(³) -t 4532 -s 4800 -v
  
  (¹) = The model of your radio, for you is 1027!
  
  (²)=The serial interface you use for CAT interface
  
  (³)= The serial interface you use for your PTT (if any)
  
  More details: /usr/bin/rigctld -h
  
  marco@linux-turion64:~> rigctld -h
  Usage: rigctld [OPTION]...
  Daemon serving COMMANDs to a connected radio transceiver or receiver.
  
  -m, --model=ID    select radio model number. See model list
    -r, --rig-file=DEVICE set device of the radio to operate on
    -p, --ptt-file=DEVICE set device of the PTT device to operate on
    -d, --dcd-file=DEVICE set device of the DCD device to operate on
    -P, --ptt-type=TYPE   set type of the PTT device to operate on
    -D, --dcd-type=TYPE   set type of the DCD device to operate on
    -s, --serial-speed=BAUD   set serial speed of the serial port
    -c, --civaddr=ID  set CI-V address, decimal (for Icom rigs only)
    -t, --port=NUM    set TCP listening port, default 4532
    -T, --listen-addr=IPADDR  set listening IP address, default ANY
    -C, --set-conf=PARM=VAL   set config parameters
    -L, --show-conf   list all config parameters
    -l, --list    list all model numbers and exit
    -u, --dump-caps   dump capabilities and exit
    -o, --vfo do not default to VFO_CURR, require extra vfo arg
    -v, --verbose set verbose mode, cumulative (-v to -v)
    -W, --twiddle_timeout timeout after detecting vfo manual change
    -x, --uplink  set uplink get_freq ignore, 1=Sub, 2=Main
    -Z, --debug-time-stamps   enable time stamps for debug messages
    -h, --help    display this help and exit
    -V, --version output version information and exit
  
Commands (some may not be available for this rig):
  F: set_freq    (Frequency) f: get_freq    ()
  M: set_mode    (Mode,Passband) m: get_mode    ()
  I: set_split_freq  (TX Frequency)  i: get_split_freq  ()
  X: set_split_mode  (TX Mode,TX Passband) x: get_split_mode  ()
  K: set_split_freq_mode(TX Frequency,TX Mode,TX Passband)  k: get_split_freq_mode()
  S: set_split_vfo   (Split,TX VFO)  s: get_split_vfo   ()
  N: set_ts  (Tuning Step)   n: get_ts  ()
  L: set_level   (Level,Level Value) l: get_level   (Level)
  U: set_func    (Func,Func Status)  u: get_func    (Func)
  P: set_parm    (Parm,Parm Value)   p: get_parm    (Parm)
  G: vfo_op  (Mem/VFO Op)    g: scan    (Scan Fct,Scan Channel)
  A: set_trn (Transceive)    a: get_trn ()
  R: set_rptr_shift  (Rptr Shift)    r: get_rptr_shift  ()
  O: set_rptr_offs   (Rptr Offset)   o: get_rptr_offs   ()
  C: set_ctcss_tone  (CTCSS Tone)    c: get_ctcss_tone  ()
  D: set_dcs_code    (DCS Code)  d: get_dcs_code    ()
  ?: set_ctcss_sql   (CTCSS Sql) ?: get_ctcss_sql   ()
  ?: set_dcs_sql (DCS Sql)   ?: get_dcs_sql ()
  V: set_vfo (VFO)   v: get_vfo ()
  T: set_ptt (PTT)   t: get_ptt ()
  E: set_mem (Memory#)   e: get_mem ()
  H: set_channel (Channel)   h: get_channel (Channel,Read Only)
  B: set_bank    (Bank)  _: get_info    ()
  J: set_rit (RIT)   j: get_rit ()
  Z: set_xit (XIT)   z: get_xit ()
  Y: set_ant (Antenna,Option)    y: get_ant (AntCurr)
  ?: set_powerstat   (Power Status)  ?: get_powerstat   ()
  ?: send_dtmf   (Digits)    ?: recv_dtmf   ()
  *: reset   (Reset) w: send_cmd    (Cmd)
  W: send_cmd_rx (Cmd,Reply) b: send_morse  (Morse)
  ?: stop_morse  ()  ?: wait_morse  ()
  ?: send_voice_mem  (Voice Mem#)    ?: get_dcd ()
  ?: set_twiddle (Timeout (secs))    ?: get_twiddle ()
  ?: uplink  (1=Sub, 2=Main) ?: set_cache   (Timeout (msecs))
  ?: get_cache   ()  2: power2mW    (Power [0.0..1.0],Frequency,Mode)
  4: mW2power    (Pwr mW,Freq,Mode)  1: dump_caps   ()
  3: dump_conf   ()  ?: dump_state  ()
  ?:

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Andras Bato

Bill,
I have switched back to CW now.
Let me wait for WSJT-X 2.3.0
Then, I am going to investigate the problem again.
Have a nice Christmas!
Andras HA6NN

On Mon, Dec 21, 2020 at 1:41 PM Bill Somerville 
wrote:

> Andras,
>
> I do not see any record of a rig control issues reported by you on this
> list. Perhaps you can share the details so a resolution can be found?
>
> 73
> Bill
> G4WJS.
>
> On 21/12/2020 09:34, Andras Bato wrote:
>
> Thank you so much, Mike.
> I haven't got any written details about the possible difference so far.
> The hard truth was when MSHV was working nicely with my FT450D
> and WSJT-x reported rig failure.
> Andras HA6NN
>
>
> On Sun, Dec 20, 2020 at 11:47 PM Black Michael via wsjt-devel <
> wsjt-devel@lists.sourceforge.net> wrote:
>
>> There's no practical difference between the 450 and 450D
>> The 450D is recognized to be the same as the 450.
>>
>> I'll contact you off-line about debugging the problem.
>>
>> Mike W9MDB
>>
>
> ___
> wsjt-devel mailing list
> wsjt-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
>
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Bill Somerville


Andras,

I do not see any record of a rig control issues reported by you on this 
list. Perhaps you can share the details so a resolution can be found?


73
Bill
G4WJS.

On 21/12/2020 09:34, Andras Bato wrote:

Thank you so much, Mike.
I haven't got any written details about the possible difference so far.
The hard truth was when MSHV was working nicely with my FT450D
and WSJT-x reported rig failure.
Andras HA6NN


On Sun, Dec 20, 2020 at 11:47 PM Black Michael via wsjt-devel 
> wrote:


There's no practical difference between the 450 and 450D
The 450D is recognized to be the same as the 450.

I'll contact you off-line about debugging the problem.

Mike W9MDB



___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

2020-12-21 Thread Andras Bato

Thank you so much, Mike.
I haven't got any written details about the possible difference so far.
The hard truth was when MSHV was working nicely with my FT450D
and WSJT-x reported rig failure.
Andras HA6NN


On Sun, Dec 20, 2020 at 11:47 PM Black Michael via wsjt-devel <
wsjt-devel@lists.sourceforge.net> wrote:

> There's no practical difference between the 450 and 450D
> The 450D is recognized to be the same as the 450.
>
> I'll contact you off-line about debugging the problem.
>
> Mike W9MDB
>
>
>
>
> On Sunday, December 20, 2020, 04:30:18 PM CST, Andras Bato <
> ha6nn.a...@gmail.com> wrote:
>
>
> Gentlemen,
> I can't find my radio in WSJT-X settings.
> The software says rig failure.
> Only MSHV has both FT450 and FT450D in the radio list.
> MX & HNY
> Andras HA6NN
> ___
> wsjt-devel mailing list
> wsjt-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
> ___
> wsjt-devel mailing list
> wsjt-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/wsjt-devel
>
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

2020-12-20 Thread Marco Calistri


  
Il 20/12/20 12:44, Andras Bato ha
  scritto:


  
  
Gentlemen,
I can't find my radio in WSJT-X settings.
The software says rig failure.
Only MSHV has both FT450 and FT450D in the radio list.
MX & HNY
Andras HA6NN

  
  
  
  
  
  ___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel


I suppose you could give a try with FT450.

1027  Yaesu  FT-450  20201219.0 
Stable  RIG_MODEL_FT450

I have FT100 but I suppose any FT100D user is using this setting.

Regards,

---
  73 de Marco, PY1ZRJ (former IK5BCU)
  
  

___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

2020-12-20 Thread Black Michael via wsjt-devel

There's no practical difference between the 450 and 450D
The 450D is recognized to be the same as the 450.
I'll contact you off-line about debugging the problem.
Mike W9MDB

 

On Sunday, December 20, 2020, 04:30:18 PM CST, Andras Bato 
 wrote:  
 
 Gentlemen,I can't find my radio in WSJT-X settings.The software says rig 
failure.Only MSHV has both FT450 and FT450D in the radio list.MX & HNYAndras 
HA6NN
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
  ___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

[wsjt-devel] FT450D is missing

2020-12-20 Thread Andras Bato

Gentlemen,
I can't find my radio in WSJT-X settings.
The software says rig failure.
Only MSHV has both FT450 and FT450D in the radio list.
MX & HNY
Andras HA6NN
___
wsjt-devel mailing list
wsjt-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/wsjt-devel

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

Re: [wsjt-devel] FT450D is missing

[wsjt-devel] FT450D is missing

9 matches

Site Navigation

Mail list logo

Footer information