On Saturday 10 September 2005 19:40, Jason Walker wrote:
PRI channels will reset when not in use throughout the day. A reset on a
channel should not happen when that channel is in use. This happens all the
time on my PRI circuits (TE110P and TE410P). From what I gather, it's
somewhat like a
?
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Andrew
Kohlsmith
Sent: Saturday, September 10, 2005 5:00 PM
To: asterisk-users@lists.digium.com
Subject: Re: [Asterisk-Users] TE110P reset
On Saturday 10 September 2005 19:40, Jason Walker wrote:
PRI channels
hi all. any body have the zaptel.conf and zapata.conf files for the card te110p ? please
another question when i start asterisk the te110p give the al channels busy is that correct?
[EMAIL PROTECTED] root]# cat /proc/zaptel/1
Span 1: WCT1/0 Digium Wildcard TE110P T1/E1 Card 0 HDB3/CCS/CRC4
Hi All,
I managed to get it up and running. It is my telco problem. Thanks.
Regards,
Stephen
El Flynn wrote:
Stephen wrote:
Hi All,
I have configure my Asterisk as follow (using [EMAIL PROTECTED]):
[zaptel.conf]
span=1,1,0,ccs,hdb3,yellow
bchan=1-15,17-31
dchan=16
loadzone = uk
Stephen wrote:
Hi All,
I have configure my Asterisk as follow (using [EMAIL PROTECTED]):
[zaptel.conf]
span=1,1,0,ccs,hdb3,yellow
bchan=1-15,17-31
dchan=16
loadzone = uk
defaultzone=uk
try this in your zaptel.conf:
span=1,0,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
CRC required for
Hi All,
I have configure my Asterisk as follow (using [EMAIL PROTECTED]):
[zaptel.conf]
span=1,1,0,ccs,hdb3,yellow
bchan=1-15,17-31
dchan=16
loadzone = uk
defaultzone=uk
[zapata.conf]
[channels]
switchtype=euroisdn
pridialplan=local
prilocaldialplan=local
internationalprefix=00
The problem Im having
is that a channel( random 23,22,21 etc)on a trunk between a Panasonic
TD500 and Asterisk is getting stuck every few days. Once stuck the channel
can no longer take calls and after a while will actully block calls from getting
past to available channels. You can see
Hi,
Been asking google and browsing the lists but haven't found any answers
for this. I've connected a TE110P E1 using EuroISDN to a PBX (for me
at the time unknown model). All is fine _except_ when placing calls to
mobile phones (which takes too long, more than 2 seconds it seems)
asterisk seem
Im using a TE110P as a trunk to a Panasonic KD-500 everything works
well.but Im having this problem where one of the channels becomes
blocked with a partial phone number after about two days. So if the
channel that becomes blocked is channels 23 no calls can get in. If
the
Im using a TE110P as a
trunk to a Panasonic KD-500 everything works well.but Im having this
problem where one of the channels becomes blocked with a partial phone number
after about two days.So if the channel that becomes blocked is
channels 23 no calls can get in. If the channel that
On Mon, 22 Aug 2005, Guy C. Guckenberger wrote:
Im using a TE110P as a trunk to a Panasonic KD-500 everything works
well.but Im having this problem where one of the channels becomes
blocked with a partial phone number after about two days. So if the
channel that becomes blocked is
Hello All,
Every time I make a call I get “Requested transfer
capability: 0x00 – SPEECH”, why I want the call to be alaw or ulaw
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.338 / Virus Database: 267.10.13/78 - Release Date: 8/19/2005
: [Asterisk-Users] TE110P problem
On Mon, 22 Aug 2005, Guy C. Guckenberger wrote:
Im using a TE110P as a trunk to a Panasonic KD-500 everything works
well.but Im having this problem where one of the channels becomes
blocked with a partial phone number after about two days. So if the
channel
I have a customer that has a Dell SC1420. They want to use that as
their Asterisk server w/ a Digium TE110P.
Digium's website doesn't mention this server one way or the other in
their compatibility list. Is there anyone out there using the SC1420?
If so, any problems?
Cheers,
Kevin
: [Asterisk-Users] TE110P flashing red/green when PRI connected
On Mon, 8 Aug 2005, Fredrik Lithén wrote:
I'm having difficulties getting up my TE110P (running as a E1) when I
connect it to the PRI. If I start the server with a loopback connector
everything seems fine and the led is green but when I
On Tue, 9 Aug 2005, Fredrik Lithén wrote:
Yes, I tried that but it sent me a bit offtrack as it reported blue
which I assumed was a clocksync problem, or at least, that was the info
I could find.
As far as I can tell zttool/zaptel uses the term BLue Alarm for the E1
term AIS (Alarm Indication
Users Mailing List - Non-Commercial Discussion
Subject: RE: [Asterisk-Users] TE110P flashing red/green when PRI connected
On Tue, 9 Aug 2005, Fredrik Lithén wrote:
Yes, I tried that but it sent me a bit offtrack as it reported blue
which I assumed was a clocksync problem, or at least
On Tuesday 09 August 2005 04:32, Peter Svensson wrote:
A bitstream is present at the receiver, though it is unframed and invalid
(i.e. the receiver is seeing a transmitter that does not quite know what
to transmit). This is different from a red alarm where there is no
bitstream at all.
I
On Tue, 9 Aug 2005, Andrew Kohlsmith wrote:
On Tuesday 09 August 2005 04:32, Peter Svensson wrote:
A bitstream is present at the receiver, though it is unframed and invalid
(i.e. the receiver is seeing a transmitter that does not quite know what
to transmit). This is different from a red
with either the wiring, the PC or something else?
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Peter Svensson
Sent: den 9 augusti 2005 14:11
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: Re: [Asterisk-Users] TE110P flashing red/green
On Tue, 9 Aug 2005, Fredrik Lithén wrote:
Perhaps everything isn't as spiffy as I thought
When running zttool the card still reports as internally clocked
Zaptel.conf:
# Global data
span=1,1,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
Zttool still shows the card as internally
Hi
I'm having difficulties getting up my TE110P (running as a E1) when I connect
it to the PRI. If I start the server with a loopback connector everything seems
fine and the led is green but when I connect it to the PRI the flashing starts
I can't seem to find anything in the log
On Mon, 8 Aug 2005, Fredrik Lithén wrote:
I'm having difficulties getting up my TE110P (running as a E1) when I
connect it to the PRI. If I start the server with a loopback connector
everything seems fine and the led is green but when I connect it to the
PRI the flashing starts
The
PM
To:
asterisk-users@lists.digium.com
Subject: [Asterisk-Users] TE110P
Cable Pin Out
I have just got a TE110P card, and I need the cable pin out.
Thanks
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.338 / Virus Database: 267.9.5/58 - Release
PRI CARD PINS
1 GREEN
2 RED
3
4 YELLOW
5 BLACK
6
7
8
PROVIDER PINS
1
2
3 YELLOW
4 GREEN
5 RED
6 BLACK
7
8
this setting work for us.
We are located in slovenia, europe.
On 7/27/05, Paul Dracevich [EMAIL PROTECTED] wrote:
I have just got a TE110P card, and I need the cable pin out.
Oggetto: Re: [Asterisk-Users] TE110P Cable Pin Out
PRI CARD PINS
1 GREEN
2 RED
3
4 YELLOW
5 BLACK
6
7
8
PROVIDER PINS
1
2
3 YELLOW
4 GREEN
5 RED
6 BLACK
7
8
this setting work for us.
We are located in slovenia, europe.
On 7/27/05, Paul Dracevich [EMAIL PROTECTED] wrote:
I have just got
: Re: [Asterisk-Users] TE110P Cable Pin Out
PRI CARD PINS
1 GREEN
2 RED
3
4 YELLOW
5 BLACK
6
7
8
PROVIDER PINS
1
2
3 YELLOW
4 GREEN
5 RED
6 BLACK
7
8
this setting work for us.
We are located in slovenia, europe.
On 7/27/05, Paul Dracevich [EMAIL PROTECTED] wrote:
I have just got a TE110P card
Paul Dracevich wrote:
I have just got a TE110P card, and I need the cable pin out.
http://www.gcom.com/home/support/t1crossover.html
Doug
___
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
On Wed, 27 Jul 2005, Paul Dracevich wrote:
I have just got a TE110P card, and I need the cable pin out.
The TE110P cards use the standard T1/E1 modular pinout. See
http://www.samhassan.com/isdn60.gif.
1 Receive from pstn (tip2)
2 Receive from pstn (ring2)
4 Transmit to pstn (ring1)
5
I have just got a TE110P card, and I need the cable pin out.
Thanks
--
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.338 / Virus Database: 267.9.5/58 - Release Date: 7/25/2005
___
Asterisk-Users
I guess you've solved this already.. but just in case, you should rmmod zaptel and modprobe it again.. I'm pretty sure you had a different version of zaptel loaded and you should be using the new one.
On Wed, 2005-06-22 at 15:58 +, MSEYE wrote:
Hi everybody !
I'm trying to setup
Hi everybody !
I'm trying to setup a TE110P card. But i'm facind this
error... and * cannot start.
[chan_zap.so]Jun 22 11:50:33 WARNING[16384]:
loader.c:248 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so:
undefined symbol: pri_dump_infoJun 22 11:50:33 WARNING[16384]: loader.c:429
I'm using it and it's great. I have it doing very basic routing from
the PSTN to SIP.
Manjit Riat wrote:
Hi,
I
was going to
order the T100P but it is replaced by TE110P. On further reading the
TE110P
does not need an external router (The one that separates the
Can anyone with a TE110p confirm that it will fit and work in both a 3.3 and
5 volt pci slot? From photos it looks to be a universal card but the digium
literature makes no mention of voltage requirements.
Craig
___
Asterisk-Users mailing list
Hi All, I just installed a TE110P card and I'm trying to compile the
code. I followed to the letter the instructions. This is what happens.
[EMAIL PROTECTED] zaptel]# make clean
rm -f torisatool makefw tor2fw.h
rm -f zttool
rm -f *.o ztcfg tzdriver sethdlc sethdlc-new
rm -f zonedata.lo
Ok I [EMAIL PROTECTED] up. I didn't realize the card is 3.3 volts and my new computer
is 5V. Can anyone point me to a PCI to PCI bridge. Any suggestions?
Mike
___
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
Subject: [Asterisk-Users] TE110P
Ok I [EMAIL PROTECTED] up. I didn't realize the card is 3.3 volts and my new
computer
is 5V. Can anyone point me to a PCI to PCI bridge. Any suggestions?
Mike
I discovered my computer is 5v and the TE110P is 3.3V Could these
errors be because there was no card?
Michael D Schelin wrote:
Hi All, I just installed a TE110P card and I'm trying to compile the
code. I followed to the letter the instructions. This is what happens.
Hello,
I still try to connect a TE110P card to a TMS2 card in a Siemens HiPath
3750.
The TMS2 card can be used to connect to an NT (Amtsanschluss)
or to connect to another S2M-Line (PRI). When connecting to another PRI,
I can select between CorNet (proprietary), ECMA-QSIG and ISO-QSIG.
It seems
On Tue, Apr 12, 2005 at 12:15:02PM +0200, Henry Jensen wrote:
Hello,
I still try to connect a TE110P card to a TMS2 card in a Siemens HiPath
3750.
The TMS2 card can be used to connect to an NT (Amtsanschluss)
or to connect to another S2M-Line (PRI). When connecting to another PRI,
I can
On Tue, Apr 05, 2005 at 09:06:33PM +0200, Peter Svensson wrote:
A yellow alarm means the remote end is sensing some error condition. Try
looking for an error message at the remote end. It may be as easy as a
broken cable (where the Hipath does not hear the Asterisk box).
The problem is,
Hi,
this blinking problem of yours occured to me and it vanished when I told
Hicom to be the master of the line and * the slave.
How exactly do I tell asterisk to be the slave?
AFAIK signalling=pri_cpe in zapata.conf means, that asterisk is the slave,
and signalling=pri_net means master, or
Hello,
I've connected a TE110P from digium with a E1/T1 crossover cable,
according to http://www.voip-info.org/wiki-crossover+T1+cable, to
a s2m port on a Siemens Hipath 3750.
The lights on the TE110p are flashing red and green, zttool reports
Yellow Alarm
Asterisk says:
pri_dchannel: PRI got
: [Asterisk-Users] TE110P/Hipath3750 - Yellow Alarm
Hello,
I've connected a TE110P from digium with a E1/T1 crossover cable,
according to http://www.voip-info.org/wiki-crossover+T1+cable, to
a s2m port on a Siemens Hipath 3750.
The lights on the TE110p are flashing red and green, zttool reports
Yellow
I had this problem in Africa. I was not provided any docs fromt he telco
but the problem was the crc4. when omitted everthing was fine.
I tried this too, no effect, still yello alarm.
___
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
Am Dienstag 05 April 2005 18:04 schrieb Henry Jensen:
Hello,
I've connected a TE110P from digium with a E1/T1 crossover cable,
according to http://www.voip-info.org/wiki-crossover+T1+cable, to
a s2m port on a Siemens Hipath 3750.
The lights on the TE110p are flashing red and green, zttool
On Tue, 5 Apr 2005, Henry Jensen wrote:
I've connected a TE110P from digium with a E1/T1 crossover cable,
according to http://www.voip-info.org/wiki-crossover+T1+cable, to
a s2m port on a Siemens Hipath 3750.
The lights on the TE110p are flashing red and green, zttool reports
Yellow Alarm
Hi,
we've installed te110p with Suse 9.2 on Siemens primergy. We're connecting
to voxsteam i60 to test PRI interface.
We have problems, after reboot sometimes it goes green, otherwise stays
blinking red.
How could we debug this situation ?
Are there any common advices what to check ?
Are CVS
- Original Message -
From: Robert Rozman [EMAIL PROTECTED]
To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
Sent: Saturday, March 19, 2005 12:36 AM
Subject: [Asterisk-Users] Te110P initial installation problems ?
Hi,
thank you for last info
@lists.digium.com
Sent: Saturday, March 19, 2005 4:16 PM
Subject: Re: [Asterisk-Users] Te110P initial installation problems ?
- Original Message -
From: Robert Rozman [EMAIL PROTECTED]
To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
Sent: Saturday, March
Hi,
thank you for last info. we've tried to use te110p but failed. We're quite
surprised that cable wasn't included with the card as any documentation, at
least on HW setup and installation, yet cable pinout for connection to PRI
interfaces
1. We have followed instructions on your site and
I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I
consistently get one of the following errors:
PRI got event: HDLC Abort (6) on Primary D-channel of span 1
or
PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1
My zaptel.conf file:
Am Donnerstag 17 März 2005 12:26 schrieb J Thomas:
I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I
consistently get one of the following errors:
PRI got event: HDLC Abort (6) on Primary D-channel of span 1
or
PRI got event: HDLC Bad FCS (8) on Primary D-channel of
Hello to all,
I would like to ask some Digium TE110P users if they can share experiance
about this card. I put in service card yesterday but I noticed following
(strange) behaviar:
- if I have to reboot my computer my zaptel driver fail to start and
produce this error:
ZT_SPANCONFIG failed
I have noticed the following:
- the PCI ID of the card seems to change over time which means that
loading the module does not always recognise the card, only way to reset
this is to power cycle the machine
- you cannot unload the module once it is loaded, it hangs the
machine, which also
- the PCI ID of the card seems to change over time which means that
loading the module does not always recognise the card, only way to reset
this is to power cycle the machine
I noticed this behaviour as well.
i thought it was my motherboard wrongly assigning irq values -
the symptoms i noticed
the TE405 and TE410. They apparently can get locked up, and only a
power cycle will clear it.
My feeling (unsupported) is that the powercycle does a better job of
forcing the far end
of an E1 (e.g. the PTT's equipment) to start afresh than just
reinitializing the cards.
I have performed
On 7 Mar 2005, at 08:42, Alfredo Sola wrote:
I don't think you can go to a customer and tell him to reboot the
PBX if it doesn't work, like a windows 98, especially after shelling
out a nice amount for the card.
No, absolutely not. My powercycle advice is only relevant when you
change the
On March 7, 2005 03:42 am, Alfredo Sola wrote:
- Unplug the PRI. The green light stays ON!
- modprobe -r wcte11xp. Green light stays ON
The card is *most certainly* locked up.
- power up. Red light blinking at about 1 Hz.
- re-plug the PRI. Green light on immediately.
This is mostly
- Asterisk won't start, known problem (ownership of /dev/zap should be
asterisk... Another thing for the owner of Makefile). Corrected; on
Not true; this is only a known issue for those who do not run asterisk as
root.
Ok, I'll correct. I would like to be able to set in the Makefile which
On March 7, 2005 05:16 pm, Alfredo Sola wrote:
Ok, I'll correct. I would like to be able to set in the Makefile which
user I'll be using, so that permissions can be set accordingly. No
problem AFAIAC if the default user is root. Perhaps time for an autoconf?
Autoconf is like using a cannon to
On Mon, Mar 07, 2005 at 11:16:18PM +0100, Alfredo Sola wrote:
Ok, I'll correct. I would like to be able to set in the Makefile
which user I'll be using, so that permissions can be set accordingly.
No
problem AFAIAC if the default user is root. Perhaps time for an autoconf?
Hi,
I've no experience with the TE110, but this is a known problem with the
TE405 and TE410. They apparently can get locked up, and only a power
cycle will clear it.
Good hint, I'll take that into account when testing.
Hope the TE100 is better built than that, though. At least, for
On 5 Mar 2005, at 18:44, Alfredo Sola wrote:
Hi,
I've no experience with the TE110, but this is a known problem with
the TE405 and TE410. They apparently can get locked up, and only a
power cycle will clear it.
Good hint, I'll take that into account when testing.
Hope the TE100 is
On March 5, 2005 04:15 pm, tim panton wrote:
My feeling (unsupported) is that the powercycle does a better job of
forcing the far end
of an E1 (e.g. the PTT's equipment) to start afresh than just
reinitializing the cards.
If you turn the power off you can be sure that you are going to drop
My feeling (unsupported) is that the powercycle does a better job of
forcing the far end
of an E1 (e.g. the PTT's equipment) to start afresh than just
reinitializing the cards.
If you turn the power off you can be sure that you are going to drop
carrier, clock and any
control lines
Hi,
I have been using asterisk for a couple of months now and for thee most
part, I love it.
However, I'm having a problem with the drivers of the Digium TE110P. I
have tried both the Debian package and the CVS. I have tried several
kernels, and am now at 2.6.11.
This has been working
Just to confirm that you also powered down and up?
I've no experience with the TE110, but this is a known problem with the
TE405 and TE410. They apparently can get locked up, and only a power
cycle will clear it.
Regards
Scott Stingel
www.evtmedia.com
Alfredo Sola wrote:
Hi,
I have
Hi All,
I have a TE110P in E1 mode, in a dell poweredge 250.
The 30 channel E1 supplied is from a telco in Australia, with the following
in my zaptel.conf:
span=1,1,0,ccs,hdb3
bchan=1-15
dchan=16
bchan=17-31
(yes the provider has NOcrc4 for some reason)
After installing the latest cvs libpri and
Hi All,
I fixed the missed IRQ's with the following reference:
http://lists.digium.com/pipermail/asterisk-users/2004-July/054712.html
At 01:09 AM 26/01/2005, you wrote:
Hi All,
I have a TE110P in E1 mode, in a dell poweredge 250.
The 30 channel E1 supplied is from a telco in Australia, with the
PROTECTED] Behalf Of Andre FAURE
Sent: Tuesday, 18 January 2005 11:59 PM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] TE110P as E1
Hello,
I'm having problem with a wildcard TE110P. As soon as I load
the module (wcte11xp for kernel 2.6.10), it spawns a yellow
error with or without an E1
Hello,
I'm having problem with a wildcard TE110P. As soon as I load
the module (wcte11xp for kernel 2.6.10), it spawns a yellow
error with or without an E1 plugged-in.
Any one managed to set it up in France?
Here are my files:
zaptel.conf:
span=1,0,0,ccs,hdb3,crc4
bchan=1-15
dchan=16
Hi Andrew,
E100P does work with Telstra, its not not Aticked. Its up to you if you
want to not tell them. E400 does.
- luke
Andrew Thrift wrote:
Hi All,
We are currently running Asterisk 1.0.3-BRISTUFFED on Gentoo Linux
with a 2.6 Kernel and this is connected to a Telecom ISDN-BRI
connection
Hi All,
We are currently running Asterisk 1.0.3-BRISTUFFED on Gentoo Linux with
a 2.6 Kernel and this is connected to a Telecom ISDN-BRI connection with
an HFC-S card, this works quite well but as you can imagine, 2 lines is
not enough for a company with 40 VoIP phones.
We are about to have
Good day all
We got a Wildcard TE110P
I installed linux,zaptel,libpti and asterisk
I coped over my zaptel.conf and zapata.conf from a previous E100P config
But when I try to start asterisk it gives error not bying able to load
zap channles:
== Parsing '/etc/asterisk/zapata.conf': Found
Jan 10
: [Asterisk-Users] TE110P error
Good day all
We got a Wildcard TE110P
I installed linux,zaptel,libpti and asterisk
I coped over my zaptel.conf and zapata.conf from a previous E100P config
But when I try to start asterisk it gives error not bying able to load
zap channles:
== Parsing '/etc/asterisk
isn't loaded or the zap
config files aren't agreeing with each other.
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Altus
Snyman
Sent: Monday, January 10, 2005 1:24 AM
To: asterisk
Subject: [Asterisk-Users] TE110P error
Good day all
We got
List - Non-Commercial Discussion
Subject: RE: [Asterisk-Users] TE110P error
On Mon, 2005-01-10 at 01:33 -0500, Alexander Lopez wrote:
You are using a PRI based config for POTS lines. It will no worky.
Post
your zap*.conf files.
I'll take a look at them for you..
How do you plug analog lines
: [Asterisk-Users] TE110P error
Good day all
We got a Wildcard TE110P
I installed linux,zaptel,libpti and asterisk
I coped over my zaptel.conf and zapata.conf from a previous E100P config
But when I try to start asterisk it gives error not bying able to load
zap channles:
== Parsing '/etc
Title: Mensaje
If you don't have any other zaptel cards what is
this card?
Lyle
Bus 2, device 5, function
0: Network controller: Tiger Jet Network Inc. Model 300
128k (rev 0). IRQ
12. Master Capable. Latency=32.
Min Gnt=1.Max Lat=128. I/O at 0xa400
[0xa4ff].
Title: Mensaje
Hi all,
I have
installed a TE110P in a BOX but when I load zaptel module I can't see any device
in /proc/zaptel. And led of the card is green.
My zaptel.conf is the
next:
span=1,1,0,ccs,hdb3,crc4bchan=1-15,17-31dchan=16loadzone=esdefaultzone=es
and cat /proc/pci throguh
On Wed, Dec 29, 2004 at 11:59:58AM +0100, Sergio Serrano wrote:
Hi all,
I have installed a TE110P in a BOX but when I load zaptel module I can't
see any device in /proc/zaptel. And led of the card is green.
From /proc/pci, it looks like you pci bus saw the card. Are you sure that you
]
Enviado el: miércoles, 29 de diciembre de 2004 18:45
Para: Asterisk Users Mailing List - Non-Commercial Discussion;
[EMAIL PROTECTED]
Asunto: Re: [Asterisk-Users] TE110P doesn't appear in /proc/zaptel
On Wed, Dec 29, 2004 at 11:59:58AM +0100, Sergio Serrano wrote:
Hi all,
I have installed
On Wed, Dec 29, 2004 at 09:17:45PM +0100, Sergio Serrano wrote:
Yes I'm sure that I load wcte11xp. When I do wcte11xp I obtain next error:
/lib/modules/2.4.20/misc/wcte11xp.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including
invalid IO or
: Asterisk Users Mailing List - Non-Commercial Discussion;
[EMAIL PROTECTED]
Asunto: Re: [Asterisk-Users] TE110P doesn't appear in /proc/zaptel
On Wed, Dec 29, 2004 at 09:17:45PM +0100, Sergio Serrano wrote:
Yes I'm sure that I load wcte11xp. When I do wcte11xp I obtain next
error:
/lib/modules
HI,
basic question. I've got a TE110P card and I'm trying to set it up with
ztcfg with polish zone.
ioctl(ZT_LOADZONE) failed: Invalid argument
Notice: Configuration file is /etc/zaptel.conf
line 206: Unable to register tone zone 'pl'
I've got loadzone and defaultzone set to pl, and there is a
Am Sonntag, 19. Dezember 2004 21:40 schrieb Marcin Mazurek:
HI,
basic question. I've got a TE110P card and I'm trying to set it up with
ztcfg with polish zone.
ioctl(ZT_LOADZONE) failed: Invalid argument
Notice: Configuration file is /etc/zaptel.conf
line 206: Unable to register tone zone
Hi,
I've just got a TE110P card and installed at Asterisk.
I configured zapata.conf, according to
www.digium.com/index.php?menu=configuration, but the following error is
happening:
...
...
...
[chan_phone.so] = (Linux Telephony API Support)
== Parsing '/etc/asterisk/phone.conf': Found
==
Leonardo Tramontina wrote:
-- Registered channel 22, PRI Signalling signalling
-- Registered channel 23, PRI Signalling signalling
Dec 2 11:07:15 ERROR[5209]: chan_zap.c:6447 mkintf: Channel 24 is reserved
for D-channel.
I've tried many combinations on the channel parameter:
channel =
Ciao,
l gio, 2004-12-02 alle 14:10, Leonardo Tramontina ha scritto:
snip
-- Registered channel 23, PRI Signalling signalling
Dec 2 11:07:15 ERROR[5209]: chan_zap.c:6447 mkintf: Channel 24 is reserved
for D-channel.
Dec 2 11:07:15 ERROR[5209]: chan_zap.c:9274 setup_zap: Unable to
Just remember you, that you can have Digium support too!
Regards,
Denis.
Em Qui 02 Dez 2004 11:10, Leonardo Tramontina escreveu:
Hi,
I've just got a TE110P card and installed at Asterisk.
I configured zapata.conf, according to
www.digium.com/index.php?menu=configuration, but the following
Thanks Matteo and Jon!!
The problem was the jump!! I moved it and now it is working!
Leonardo
___
Asterisk-Users mailing list
[EMAIL PROTECTED]
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
101 - 192 of 192 matches
Mail list logo
