Hi List
I have had some fairly regular job failures that I have pinpointed to be
caused by tape status type error mismatches. The most common is that the
tape status does not match that of the catalogue in a number of ways.
The first is that if the catalogue reports the volume status to be
err
Hello Ryan,
sorry this got a little delayed. I copy to Your email.
<[EMAIL PROTECTED]> aka Ryan Novosielski schrieb
mit Datum Sun, 10 Feb 2008 22:37:54 -0500 in m2n.bacula.users:
|> |To the technical points you discuss, you will discover that tape
|> |mirroring is a problem, as currently cho
I have read the manual for verify jobs and I don't understand what the
directive "Verify Job" does.
The other question is where do i need to declare this?
http://www.bacula.org/en/dev-manual/Configuring_Director.html#SECTION00143
says If I run a verify job without this directive t
In the output of commands such as 'list jobs', is it possible to configure
bacula to display numeric quantities as digits alone (no commas)? I really
find this difficult to read.
-s
-
This SF.net email is sponsored by: Micr
First a quick note... drives LTO 2nd generation and newer should not
shoeshine unless you're really running way to slow a cpu for what else
is going on with the computer.
If the room air temp is less than 85 degrees or so it's unlikely in a
tape autoloader cabinet (i.e. good airflow by design)
Hi,
28.02.2008 12:49, Damian Brasher wrote:
> Hi List
>
> I have had some fairly regular job failures that I have pinpointed to be
> caused by tape status type error mismatches. The most common is that the
> tape status does not match that of the catalogue in a number of ways.
>
> The first is
Hi,
28.02.2008 15:48, Peter Much wrote:
> Hello Ryan,
>
> sorry this got a little delayed. I copy to Your email.
>
> <[EMAIL PROTECTED]> aka Ryan Novosielski schrieb
> mit Datum Sun, 10 Feb 2008 22:37:54 -0500 in m2n.bacula.users:
>
...
> It depends how You define "possible". It seems not to
Bob Hetzel wrote:
> First a quick note... drives LTO 2nd generation and newer should not
> shoeshine unless you're really running way to slow a cpu for what else
> is going on with the computer.
>
That is nice to know - Ive been doing lots of necessary things to avoid
shoeshining it seems.
>
In the message dated: Thu, 28 Feb 2008 11:21:31 EST,
The pithy ruminations from Bob Hetzel on
were:
=>
=> First a quick note... drives LTO 2nd generation and newer should not
=> shoeshine unless you're really running way to slow a cpu for what else
=> is going on with the computer.
Huh? Tha
I just tried to simulate a database crash and disaster recovery and came
to the point with restoring database with bacula-console and bootstrap file.
The documentation
http://bacula.org/en/dev-manual/Restore_Command.html#database_restore
shows the possibility to restore within console so I tried
I really don't understand this.
I can run a backup to a tape, using my 'Server' volume/pool. It completes.
It moves on to the next client, which belongs to the same volume/pool, and
then Bacula reports that there are no appendable volumes and that I should
use the label command to resolve this.
Mark Nienberg wrote:
> Can anyone shed some light on the following fatal error? It happened
> during a tape change in the middle of a full backup. The autochanger
> has been working just fine prior to this and in fact the requested tape
> was successfully loaded into the drive (status storage
> > 23-Feb 06:21 khyber-sd JobId 1843: 3304 Issuing autochanger "load slot
> > 1, drive 0" command.
> >
> > 23-Feb 06:26 khyber-sd JobId 1843: Fatal error: 3992 Bad autochanger
> > "load slot 1, drive 0": ERR=Child died from signal 15: Termination.
> > Results=Loading media from Storage Eleme
> On Thu, 28 Feb 2008 11:20:26 -0500 (EST), Steve Thompson said:
>
> In the output of commands such as 'list jobs', is it possible to configure
> bacula to display numeric quantities as digits alone (no commas)? I really
> find this difficult to read.
I don't think it is possible, except by
I stand corrected... It seems the data rate matching in LTO-3 drives
isn't as flexible as I'd have thought... One interesting thing to note
in the doc you mentioned is that if you think you may be shoe-shining,
try backing up onto an LTO-2 tape as this will run the drive at native
LTO-2 speeds
'A newbie here... please be kind&gentle.
I had differential backup scheduled to run. When it came time, it was
upgraded to full, citing "Prior failed job found..." But in fact, i had
a clean full backup (launched manually from the console) that finished
just a couple of days before. And if i tr
Hi,
Is it normal that while the volumes are being created in bacula, the labels
given to them are in crescent order?
Before, with the same configuration(unless I haven't noticed), when the
volumes were purged, the labels changes
i.e:
With 2 volumes for full backup:
Correct:
Full_Client1,FullCl
From: Tilman Schmidt <[EMAIL PROTECTED]>
>> >OfflineOnUnmount = yes; # when unmounted, eject tape
>> > [...] has two unexpected side effects.
>> > a) If I label a new tape it is ejected after the operation, followed by
>> > a message from Bacula that it couldn't mount the new tape.
Hallo Arno!
<[EMAIL PROTECTED]> aka Arno Lehmann schrieb
mit Datum Thu, 28 Feb 2008 17:38:55 +0100 in m2n.bacula.users:
|> The only thing that has changed is two values in the catalog
|> which mark the old job as migrated and the new job as the target
|> of that migration. Now if one would some
Hi,
28.02.2008 22:37, Peter Much wrote:
> Hallo Arno!
>
> <[EMAIL PROTECTED]> aka Arno Lehmann schrieb
> mit Datum Thu, 28 Feb 2008 17:38:55 +0100 in m2n.bacula.users:
>
> |> The only thing that has changed is two values in the catalog
> |> which mark the old job as migrated and the new job as
John Drescher wrote:
>> > 23-Feb 06:21 khyber-sd JobId 1843: 3304 Issuing autochanger "load slot
>> > 1, drive 0" command.
>> >
>> > 23-Feb 06:26 khyber-sd JobId 1843: Fatal error: 3992 Bad autochanger
>> > "load slot 1, drive 0": ERR=Child died from signal 15: Termination.
>> > Results=Loadi
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Martin Simmons wrote:
>> On Thu, 28 Feb 2008 11:20:26 -0500 (EST), Steve Thompson said:
>> In the output of commands such as 'list jobs', is it possible to configure
>> bacula to display numeric quantities as digits alone (no commas)? I really
>>
22 matches
Mail list logo
