On most furnaces the blower continues to run as long as there is heat stored
in the heat exchanger. In milder weather the burner comes on before the
blower does and the blower stays on after the burner has turned off. In
your case the burner may be cycling off and on but the cycles are so shor
Hi,
It's bitterly cold here today; probably didn't get past 15 degrees.
When we leave, we turn our talking thermostat down to 68, but since we got
home, we turned it up to 70; that was at about 4 PM this afternoon.
Could the timer have gone out or something? The furnace hasn't turned off
once!
Quite a few years ago I had an older blind ham friend that lived in a
retirement home. He was not allowed to put out any antennas and he came up
with this idea. Right outside his window was the down spout for the rain
gutters. He found where it went to the ground and then had another ham
friend
You don't ground the antenna. You ground the ground terminal of the
receiver, if it has one. That gives the antenna something to work against.
Having an antenna without a ground is like trying to operate a light bulb
from one wire. You always need two wires to make a complete circuit. Some
Thanks Clifford, it's nice to know grounding isn't set in stone so to speak.
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:blindhandy...@yahoogroups.com]
On Behalf Of clifford
Sent: Monday, December 15, 2008 19:41
To: blindhandyman@yahoogroups.com
Subject: [BlindHandyMa
Dear William:
The loop antennas I described are not grounded, although I do have a ground
wire that connects to my amateur rig. Some antennas are grounded at a point,
either at the receiver end or some are grounded through a resister at the
opposite end of the antenna.
I had a ham frie
Thanks to all who have answered this one for me. Can somebody explain how
to and why we should ground antennas? If memory serves, when I have touched
an antenna wire to a ground, like plumming say, the signal went away
entirely. So, what am I missing?
Thanks again.
-Original Messa
Dear Max and list members:
The best ham antennas I have ever had were full-wave loop antennas. On 75
meters, the square was roughly sixty feet per side, with four sides. I
constructed the loop with number 14 copper-clad steel wire, with a matching one
to one transformer at the corner and a
After all of the discussions about palm nailers I thought it might be
something to add to my arsenal of tools. Calling around I learned that the
Sears store no longer carries them that they are available by catalog only.
Home Depot has a Rigid for $80, Lowes has a Bostige, I think that is how i
If the glaze is a two-part mix like epoxy, try putting heat on the surface with
lamps. The heat may have to remain for some hours or even a day to get the
glaze to continue Hardening and end up non-sticky.
- Gil Laster, Charlotte, NC
[Non-text portions of this message have been removed]
I also have gutters joined at right angles that dripped. Mine are mitered and
held together with screws. I unscrewed the joint, applied sealant to the joint
flanges, and put it back together. "DAP Flashing and Gutter Butyl-flex
sealant" purchased at The Home Depot has held without leaking for
By Matt Weber
as we were covering the kitchen floor with tile, we thought it would be nice
to add a radiant heat system, but needed a DIY-friendly setup that we could
install quickly without a lot of major reconstruction. So we turned to MP
Global Products, a company which distributes a two-compo
There was hardener in int.I can try heating it up.
Dale
- Original Message -
From: Dale Leavens
To: blindhandyman@yahoogroups.com
Sent: Monday, December 15, 2008 5:33 AM
Subject: Re: [BlindHandyMan] Sticky glaze
You won't likely be able to add hardener at this point unless
I'd use silicone caulking, but it's not extremely cold here in California.
Also, I've used a tar like substance in the pan of a swamp cooler that was
rusting out in some of the areas and it worked great. I'd apply this stuff
and an hour or two later I'd turn the valve on that allow the water to
are you a smart handyman or handwoman and unplug all the tools that
you use once done with them. is your affairs in order with supplies
should your power go off. we have had off / on power for the last few
days after the initial ice storm. today they are doing a big grid shut
down f
You won't likely be able to add hardener at this point unless you apply another
thin coat with a touch more hardener but I don't know how that finish would end
up.
Try warming it up a little though, that might be enough. Not too hot, maybe a
small heater blowing on it or low heat hair dryer.
I
I've seen the ones that have the lever coming out of the wall. I've never seen
one with a key though.
In any event finding out a name is the best place to start. You might also
want to Google chimney sweeps in your zip code. A certified chimney sweep will
be most familiar with a damper. Y
17 matches
Mail list logo