Hi,
Corporate Directory search on my cisco ip communicator doesn't work, so I
want to run Directory Wizard and in order to run it I should run Cisco
IP Communicator
Administration Tool ,but where is this tool located ?,I couldn't find any
info in Docs.
Jeremy
HI,
I am getting following when trying to register Cat6K port to CCM on Pod 20.
I've tried enabling/disabling the ports but all three ports (T1, Xcode and CFB)
are in same state. Reset the DHCP service, other devices are able to take IP
Address from DHCP and enough IPs are available in the sco
Still have the same problem,
PSTN-WAN GK send extra digit to my E1 (BR2 Site)
Thanks
David Corbeil
Consultant en technologie | Technology Consultant
Tel. 514-215-2490 | Fax. 514-748-5333
Membre de l'équipe TELUS
From: David Corbeil
Sent: Thursday, October 02, 200
How you can reach the voicemail, when you have a WAN outage?
You can't dial 1600 directly like that, you need a dial-peer to call outside
and reach the voicemail by the PSTN.
Can you confirm that 24.26 is not a good answer and missing some configuration ?
Thanks
David Corbeil
Consultant en tec
I also had same problem with once...
try do disable all the port
!
set port disable 7/2-4
!
then change dhcp enable to static for each port
!
set port voice interface 7/2 dhcp disable 10.10.10.1/24 gateway 10.10.10.10
tftp 10.10.10.10 dns cisco.com
!
then change back static to dhcp enable
!
set
Hi David,
First of all, you should carefully check your "voice translation-rule" and your
"num-exp". Looks like you have some runaway translations, which insert and/or
drop digits into your dialing string.
When you look really close to your digits, you will notice that they are not
that much
Not this time
I prefix 011331322 because I now on pod 12
And I receive that "Called Number=33132433313223001"
So I receive this extra digit "3313243"
So past Thursday a tech call me from IP EXPERT to change Translation in
PSTN-WAN to fix the problem.
Thanks
David Corbeil
Consultant en techno
If COR is configured on H323 dial-peers on an H323 gateway, is the
dial-peer COR only in affect when in SRST mode ? If not, wouldn't you
be performing COR twice once on the CallManager and also on the
H323-GW ?
for example:
phones/CSS > h323-gw inbound voip dial-peer (KEY) ---> h323gw
o
QoS - Question.
After setting up a policy to macth RTP and signalling in a LLQ policy in which
I used 96k for rtp and 8k for SIG across the WAN.
The PVC is 384k.
What if another question was asked to make sure that the remaining traffic's
dscp marking must be maintained if the pvc is utilized
Mike,
I was under the impression since the call came into the H323 gateway from
UCM (GW isn't in SRST) it wasn't "tagged" with an incoming corlist and
therefore could reach all remote PSTN numbers. When the router drops back
to SRST the phones would register with a corlist incoming and therefore b
Hi,
Someone knows why when the publisher is down, the aar is not working?
I have a busy after I shutdown the ccm pub service.
Thanks
David Corbeil
Consultant en technologie | Technology Consultant
Tel. 514-215-2490 | Fax. 514-748-5333
Membre de l'équipe TELUS
When not in SRST mode, all layer-3 information (DNIS, ANI) are back-hauled to
CCM directly and COR won't trigger.
Jacob Owen <[EMAIL PROTECTED]> wrote: Mike,
I was under the impression since the call came into the H323 gateway from UCM
(GW isn't in SRST) it wasn't "tagged" with an incoming corli
Hi David,
Do you have gateways registered to both, Pub and Sub? Would you check the
gateways status when the publisher id down?
Sincerely,
Mike
http://cciev.headsetadapter.com
- Original Message -
From: David Corbeil
To: 'ccie_voice@onlinestudylist.com'
Sent: Sunday, October
Kapil,
I am referring to an H323 gateway not an MGCP gateway. Therefore L3
info is not backhauled to CM.
Regards,
Mike Brooks
CCIE#16027 (R&S)
On Sun, Oct 5, 2008 at 3:58 PM, kapil atrish <[EMAIL PROTECTED]> wrote:
> When not in SRST mode, all layer-3 information (DNIS, ANI) are back-hauled
>
Hello,
In working through this problem and referencing the solution, I noticed
that the solution does not include dial-peers so that phones at BR2 at able
to call HQ phones via IPIPGW. I'm not sure if this is an omission or if the
syntax has been added elsewhere. The two problems I have are;
Nope - you didn't have a typo - I just 'assumed' G729 and skipped
actually 'reading' the part that clearly said g711.
:P
Sorry,
--
Mark Snow
CCIE #14073 (Voice, Security)
Senior Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Fax: +1.309.413.4097
Mailto: [EMAIL PROTECTED]
--
If COR is assign to incoming dial-peer (cor incoming) & outgoing dial-peer (cor
outgoing), the COR will take affect event when the gateway is not in SRST mode.
My suggestions are:
1. Do configure outgoing dial-peer to PSTN with COR
2. Do not configure incoming dial-peer from CCM with COR
3. Let t
Hi Parker,
i think the cfw in alias will work if the PSTN accept 1212225 and pass it
to HQ gateway. if the PSTN only accept 12122251xxx, then the cfw in alias will
not work. i think the workaround if still want using alias is put cfw
912122251xxx which is not already used in HQ, then use tr
Hi Guys
Is it possible to run the CallManager in security mode and run SRTP
with secure phones without the Cisco USB token . Possibly using a
windows CA to creat the certificates.
Paul
Hi All,
How can we block international (or specific calling number) call ONLY in SRST
mode? in H323 gateway.
Thanks,
Bala.
--- On Mon, 6/10/08, Edi Hamlet <[EMAIL PROTECTED]> wrote:
From: Edi Hamlet <[EMAIL PROTECTED]>
Subject: Re: [OSL | CCIE_Voice] SRST Voicemail Integration
To: "Chris
Hi,
How can we block international (or specific calling number) call ONLY in SRST
mode? in H323 gateway.
Thanks,
Bala.
--- On Mon, 6/10/08, Mike Brooks <[EMAIL PROTECTED]> wrote:
From: Mike Brooks <[EMAIL PROTECTED]>
Subject: Re: [OSL | CCIE_Voice] H323 COR ?
To: "kapil atrish" <[EMAIL PR
21 matches
Mail list logo
