Sean,
the last config you posted lloks like its on the br2 router.
you should have the
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
on the br1 router
On Wed, Apr 7, 2010 at 7:29 AM, sean hurricane wrote:
> i had that in another dial-peer, see below:
>
> dial-peer voice
Hello:
Modify voice translation-rule 9 in order to match the calling number with your
RD number
hth
Date: Wed, 7 Apr 2010 02:25:53 -0400
From: shurric...@gmail.com
To: afat...@verizon.net
CC: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] LAB 7 question 3.2 (DISA)
i
Hi,
You don't need to have complete match to only get asked about PIN when you dial
in to MVA. But there are some well known strange behaviors that can be seen in
the version of UCM we use in the lab. When you change the setting for
partial/complete match and the number of digits needed, you may
What if you change this setup somewhat to be like this instead?
Use a CTI RP in PT ToD_RollToVM_P with dn 6XXX, or whatever that matches your
internal dn’s.
Use a TP in AllHours_P with match 6XXX, send it to a CSS that can see the PT
that the phone’s dn uses. That PT need to be different than All
Q: What service is used on the CCM to communicate with CUPS?
I would say Cisco AXL web service as it is used to sync with sync Agent
at CUPS but I can see CTI Manager could very well be that service which
is needed for Desktop control...
Thoughts?
Ash>
__
i will try later tonite and report back, thanks all
2010/4/7 Roger Källberg
> Hi,
> You don't need to have complete match to only get asked about PIN when you
> dial in to MVA. But there are some well known strange behaviors that can be
> seen in the version of UCM we use in the lab. When you
sorry about that, it was almost 4:00am and eyes were getting weary. I had
the dial-peer just not in the config i posted. i seriously do not think it's
a dial-peer issue, if it was that i should just get a secondary dial-tone,
excuse my failed attempt at being clever by posting snipet of the config
I have two MGCP IOS gw set up (HQ/BR1), and they are registered and
working OK. For some reason, they seem not to be stripping the
significant digits to 4 as I have configured in CUCM. I have tired
resetting the GW and no/mgcp, as well as rebuilding the GW in CUCM.
The SIP phones can call each ot
Can you make outbound calls through your gateways?
Check your CSS/Partitions etc.
On 07/04/2010 16:05, Stephen Greszczyszyn wrote:
I have two MGCP IOS gw set up (HQ/BR1), and they are registered and
working OK. For some reason, they seem not to be stripping the
significant digits to 4 as I hav
At present the system is configured with unique CTI ports for each dn's with
ToDRollToVM_PT and i will try changing the CSS for the CER RoutePoint(which
is now same as Gateway CSS) to something else and not have the e TODRollToVm
_PT and let you know if it works.
Again thanks for all your help.
Ashar,
After rebooting my Pub/Sub I got even stranger things happening with
my SIP phones (constantly restarting). This usually signals to me
that something is wrong with replication, although RTMT showed both
servers at 2.
I switched the CUCM group to just have the Pub in it and shut down the
S
I have had more strange issues then you are having due to this
db_replication thing.
I remember few weeks back when I was practicing at one of the IPexpert
rack with Sub first and Pub second, none of my devices were showing
registered at CUCM yet they all were working perfectly normal. All my
p
*10.10.201.1 is the configured ip address in UCCM*.
On Wed, Apr 7, 2010 at 12:12 PM, James Rosenfelt wrote:
> 04/06/2010 23:57:43.327 CCM|H225Handler::SdlConnectionInd, rejecting the
> TCP connection from IP=*10.10.201.1*. Incoming H225 call on
> Port=1720, can't
> find this port in th
You could very well be another victim of db_replication.
Take off your sub from the CCM group and make everything register with PUB.
Give it a go and see if it works...
Ash>
On 07/04/2010 17:50, sean hurricane wrote:
*10.10.201.1 _is_ the configured ip address in UCCM*.
On Wed, Apr 7, 2010 at
This command use to fix db replication issues for example you reset the phone
from GUI and the phone doesn't reset, etc (ESXi 4)
utils dbreplication repair all
It takes 2-3 min and use to work as expected, sometimes it's necessary to
repeat the command a second time
I have also see
i will try that tonite.
Thanks all
On Wed, Apr 7, 2010 at 1:01 PM, Ashar Siddiqui wrote:
> You could very well be another victim of db_replication.
> Take off your sub from the CCM group and make everything register with PUB.
> Give it a go and see if it works...
>
> Ash>
>
>
> On 07/04/2010 17
I'm working through V2 Lab8 and I'm having problems with the CUBE part.
Calls are passing from HQ to BR2 fine via the CUBE in HQ, but when
they arrive in BR2, I'm getting some sort of 501 error. Calls are
working ok from the BR2 SIP phones (all 7965) in/out PSTN.
Apr 7 18:33:01.613: //-1/xx
Ensure you are allowing sip to sip connections and that you are matching an
inbound voip dialpeer on the BR2 router (as opposed to using dial-peer 0).
For calls from BR2>HQ can you check the dialplan xml file (or even remove it
altogether). Check which dial-peers you are using- it seems that you a
I'm working on Lab 8, Task 7.1 and was trying to figure out how to
accomplish the SIP SRST as outlined in the task, honoring the
requirement of "You are not allowed to create a voice translation-rule
(or translation-rule) to achieve this task. After trying various things
which didn't work I looked
Still no luck, spent hours on this tonite
On Wed, Apr 7, 2010 at 2:24 PM, sean hurricane wrote:
> i will try that tonite.
>
> Thanks all
>
> On Wed, Apr 7, 2010 at 1:01 PM, Ashar Siddiqui wrote:
>
>> You could very well be another victim of db_replication.
>> Take off your sub from the CCM group
why don't you enable the following debug on the router
debug cch323 h225, to check the call setup and check how the gw attempts to
contact the cucm.
you can also enable debug cch323 h245 to check the logical channel
negotiation
2010/4/7 sean hurricane
> Still no luck, spent hours on this toni
Sean,
There are a couple of things you can try.
First there is a CCM service param called accept tcp connections from
unknown devices or something similar, set that to true and see if the
call goes through.
If the call goes through, then you know everythings fine on the GW side
Now you can tu
Are you using the Loopback 0 ip address as the Device Name for the H323 gateway
in UCM? Do you have 'h323-gateway voip interface' and 'h323-gateway voip bind
srcaddr x.x.x.x' on the router's Loopback 0 interface so packets are sources
from Loopback 0?
On Apr 7, 2010, at 8:46 PM, sean hurrica
I am in middle of the session on Proctor labs...
I am getting " %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on
FastEthernet1/0/4 (not half duplex), with CUC7-Pub eth0 (half duplex)." on
HQ 3750 Switch.
I can ping 10.10.210.10 CUCM but can't web browse into it.
Any help will be highly appr
>From what I understand, the Duplex message is an issue with the ESX setup,
and nothing to be considered about. If it's a nuisance, disable CDP on Fa
1/0/4 with "no cdp enable"
Can you SSH into the Pub? Perhaps the services have yet to fully load.
From: ccie_voice-boun...@onlinestudylist.com
[
I would agree, first things is to verify that Tomcat is happy.
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Ryan Schwab
Sent: Thursday, April 08, 2010 1:11 AM
To: 'vccie2010'; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Vo
Mike, on that note, are there any specific CLI commands you can think of to
verify this? :)
From: Mike Thompson [mailto:mthompson...@gmail.com]
Sent: April-07-10 11:16 PM
To: 'Ryan Schwab'; 'vccie2010'; ccie_voice@onlinestudylist.com
Subject: RE: [OSL | CCIE_Voice] %CDP-4-DUPLEX_MISMATCH: dupl
Syntax escapes me right now, but there will be a show service or list
service command that will show the status of all services on the server. It
should show status as well
From: Ryan Schwab [mailto:schwab...@shaw.ca]
Sent: Thursday, April 08, 2010 1:15 AM
To: 'Mike Thompson'; 'vccie2010'; cc
Utils service list will show the list of services and their status
From: Ryan Schwab [mailto:schwab...@shaw.ca]
Sent: Thursday, April 08, 2010 1:15 AM
To: 'Mike Thompson'; 'vccie2010'; ccie_voice@onlinestudylist.com
Subject: RE: [OSL | CCIE_Voice] %CDP-4-DUPLEX_MISMATCH: duplex mismatch
dis
Just change duplex to half on the F1/0/4 port. This works for me every time.
On Thu, Apr 8, 2010 at 4:19 PM, Mike Thompson wrote:
> Utils service list will show the list of services and their status
>
>
>
>
>
> *From:* Ryan Schwab [mailto:schwab...@shaw.ca]
> *Sent:* Thursday, April 08, 2010 1:1
30 matches
Mail list logo
