You need to configure dialpeer pointing to ras
Regards,
Mohammed Al Baqari
Sent from my iPhone
On Nov 15, 2011, at 12:04 AM, Matthew Saskin wrote:
> What does the rest of your configuration on the SRST router look like? Do
> you have the requisite dial peers in place to direct calls from SRS
On you gateway, do the following:
1. Debug cch323 h225 messages. Check if any h323 signaling is reaching the
gateway.
2. If signaling is received successfully, run the command debug voice dialpeer.
Check which dial peer is matched and whats the configuration of it
3. If no h323 signaling is rece
Hi,
I know this must be lame and you must have already tried it, but just
incase, did you try to *manually hard-restart the IP Phone*?
Ive had a smilar problem once or twice. I had used phone button template.
It would work fine for a few days, then all of a sudden it would start
working ony like a
Verify the registration status of your Route List.
Try to reset it once.
Run the debug voice ccapi inout on H323 Gw and see if the outboud calls
really hitting to the gateway on not ?
On Tue, Nov 15, 2011 at 9:54 AM, Ken Wyan wrote:
> Pls check your route list rl-test configuration & digit man
Thanks Everyone.
Thanks Kshitij for this gr8 explanation. :)
On Mon, Nov 14, 2011 at 6:06 PM, Kshitij Singhi wrote:
> Hi Sonu,
>
> So for a call on the Branch site, I can think of a few scenarios:
>
> 1. Call coming in for an IP Phone at the branch site from the PSTN.
> 2. Call being made from a
Pls check your route list rl-test configuration & digit manipulations
etc.. in rg-test (under rl-test).
If you have done any digit manipulations in rg-test (under rl-test) , your
RP digit-manipulations will not work.
Add rg-test as Local Route Group for Device Pool
In addition to debug isdn --
Is there any configuration required as far as isdn type of call and Isdn plan?
Rc
Sent from my iPhone
On Nov 14, 2011, at 7:28 PM, Voiper wrote:
> Hi Follow Labbers:
>
> I am writing to get help with my lab. I have been struggling with something
> as simple as outbound calls to the PSTN! I h
Hello-
Any one knows how I can obtain CUPS license for IE Voice Lab, Right now I
am running it under Eval License.
Regards
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and lo
Did you reset the h323 gw in cucm? Do you see an ip address towards the upper
portion of the page above the name/ ip address field?
The reset changes it from unknown to the ip address
Hth
Randall
Sent from my iPhone
On Nov 14, 2011, at 7:28 PM, Voiper wrote:
> Hi Follow Labbers:
>
> I am wr
Hi Follow Labbers:
I am writing to get help with my lab. I have been struggling with something
as simple as outbound calls to the PSTN! I had got stuck with Vol 1 lab 5.2
(Standard local route) and despite many suggestions I just couldn't get it
working. So, I back tracked and tried the simplest s
Honestly!!!
>
>
>You guys have to be kidding me. I want my money back for these labs. you sold
>us something you weren't prepared to support I have been fighting these for 2
>weeks now and fixes are coming rack are being prepped is what I have heard,
>and I am 2 weeks away from by lab date and
What does the rest of your configuration on the SRST router look like? Do
you have the requisite dial peers in place to direct calls from SRST
registered phones to the gatekeeper? Without that you're not going to get
very far...the SRST router has no knowledge of the callmanager gatekeeper
config
Hi Mike,
In the lab we get:
CUCM version 7.0.1-something
CME version: 7.0.x (IOS 12.4(20)Tx
CUE version: 7.0.x
On Mon, Nov 14, 2011 at 10:30 PM, wrote:
> Send CCIE_Voice mailing list submissions to
>ccie_voice@onlinestudylist.com
>
> To subscribe or unsubscribe via the World Wide Web,
Just curious I have been playing around with a VG224 and was trying to
figure out if there is a way to tell if an analog phone is connected to a
port on a VG224 or 248? Sorry as this is a little off topic. Was hoping
someone may have stumbled upon this situation before.
Regards,
ccieiwillb
_
In addition, I could see in GK debug output, that it send the ACF in reply
to ARQ from SRST.
But I cannot see any H225 message towards the CUCME from SRST.
The "debug cch323 h225" and "debug h225 asn1" does not gives any output
after receiving the ACF from GK.
SRST is not initating H225 to CUCME
Hello everyone,
I have a problem with SRST to Gatekeeper calls.
When the IP Phone are registered with CUCM calls to CUCME through GK works
just fine.
But as soon as I will shutdown the CUCM Service on all servers, so that the
IP Phones will register with SRST Router, the outgoing calls to CUCME
t
you can preserve BW using the Shape , but once you enabled the
priority Queue out , you will disable the shaping and the sharing and
the priority Q will be always served until it will be empty .
Ash
On Mon, Nov 14, 2011 at 11:34 AM, Ken Wyan wrote:
> Hi Experts,
>
> Is it possible to reserve ba
Am I the only guy faced this issue in Proctorlabs ?
On Sun, Nov 13, 2011 at 10:14 AM, Ken Wyan wrote:
> Hi,
>
> Anybody faced this?
>
> https://supportforums.cisco.com/thread/313105
>
> (supportforum also doesn't have an answer yet )
>
> On Sun, Nov 13, 2011 at 8:06 AM, Ken Wyan wrote:
>
>> H
Hi Experts,
Is it possible to reserve bandwidth for the priority queue in egress
queuing using the command
Switch(conf-if)# srr-queue bandwidth shape 4 4 4 4
Switch(conf-if)# priority-queue out
In this case will it reserve 25% bandwidth for queue 1 (which is the
priority queue) OR will it serv
Is your UCCX server 'In Service'? If so, try restarting the CTI Manager
service in CUCM. If not, you will need to take a look at the event logs and
traces on the UCCX server to see what may be going on.
HTH
Adam
2011/11/14 bruno
> i have creat Unified CM Telephony Group #0 \ application \trigger
Does anyone out there wish to share what versions of CUCME and CUE you are
running? Any input would be appreciated. Thank you.
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP
Hi Gregg,
Yes, you are missing the dots after the MWI ON/OFF number. The reason why
CUE is not seeing the MWI on/off numbers is because an MWI "outcall" is
made by CUE in the following format:
- - - - - - - - > For switching MWI on
- - - - - - - - > For switching MWI off
Thus, if you would lea
Hi Sonu,
So for a call on the Branch site, I can think of a few scenarios:
1. Call coming in for an IP Phone at the branch site from the PSTN.
2. Call being made from a phone at Branch Site 1 to another phone at Branch
Site 1.
3. Call being made from a phone at Branch Site X to a phone at Branch
Thanks. That was the issue.
On Mon, Nov 14, 2011 at 7:07 AM, Ki Wi wrote:
> It should be 3999 The amount of . Depends on your extension number.
>
> Sent from my iPhone
> Pls pardon my fat fingers.
>
> On 14 Nov, 2011, at 7:47 PM, Gregg Malcolm
> wrote:
>
> Running into a silly problem with
It should be 3999 The amount of . Depends on your extension number.
Sent from my iPhone
Pls pardon my fat fingers.
On 14 Nov, 2011, at 7:47 PM, Gregg Malcolm wrote:
> Running into a silly problem with my CUE where the MWI isn't seen by the
> wizard nor does it work. Wizard sees the users/
Running into a silly problem with my CUE where the MWI isn't seen by the
wizard nor does it work. Wizard sees the users/DN's so the web
communication is working. Here is my config on CME:
telephony-service
authentication credential admin cisco
em logout 0:0 0:0 0:0
max-ephones 10
max-dn 50
Hi,
your configuration is ok. You will define the codec, which is actually used,
inside CUCM with Region Settings. And Settings in the Enterprise and Service
Parameters, as well.
/Robert
Von: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] Im Auftr
27 matches
Mail list logo
