can someone help me? i am currently doing bgp in my test lab. i did a
community no-advertise in one of the routes to be advertise by the local as
to another as, but i can't see it in that other as. i also did a
redistribution from bgp to igp (ospf) in the other as so that both bgp and
igp would syn
Hello Group,
Sorry for the un-related message:-
Anyone has any Voice modules that they no longer needed?
In particular, I am looking for:-
2 x NM1V
2 x NM-2FXS
Regards,
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=62323&t=62323
--
Hi Gruop,
I want to upgrade my BootROMs for my 2500s routers. Is it easy to do?
Any comments will be greatly appreciated.
Best Regards,
Hunt
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=62321&t=62321
--
FAQ, list archives,
To add to this...
The pix would operate under these conditions too. But it is absolutely not
supported by Cisco and anyone doing it should consider the hurdles. First
by having multiple interfaces facing the target IP network(global Internet).
Then by setting routes to the chosen destinations IP
Larry Letterman wrote:
>
> In most cases you will only re-write the source mac address
> when traversing
> across a L3 device. If you go across a layer 2 network, all
> the mac address's
> would typically be part of the same broadcast domain and not
> need to be changed.
>
> If you go across a T1
Hello,
Just stumbled upon this on Rip to Isis redistribution?
"If the source protocol's AD is higher than that of IS-IS, then the
originating routes may be over-ridden by the new IS-IS route leading to
flapping routes and/or incorrect next-hop addresses"
What does this actually mean? Does it me
Oh well, If I ever get working I'll post the config's and an explanation.
wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> sorry, i dont know mate :( not my strong point dude!
>
> -Original Message-
> From: Sam Sneed [mailto:[EMAIL PROTECTED]]
> Sent: 31 January 2003 21:55
""Firesox"" wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Folks I am a little stuck in IRB config.
> I have two 2620 routers connected via T1.
>
> I would llike to route IP and bridge IPX.
> On the routed IP network I need to run OSPF to connect to other networks.
first of all,
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Does not work. Pls state the tcp port you want map per internal ip
As in
(off the top of m hat)
ip nat inside source static tcp 10.22.5.4 25 209.10.248.134 25
ip nat inside source static tcp 10.22.5.5 80 209.10.248.134 80
Can also u
Please can someone tell me if multiple Private Static IPs can be NAT'ed to
one Public IP address.
when i try to did that it gave me an error "
Router(config)#ip nat inside source static 10.22.5.5 209.10.248.x
% 209.10.248.x already mapped (10.22.5.4 -> 209.10.248.x)
--
This is
Got a chance to test this. The RR will reflect the best path
based on it's own local view of the world. Thus, if everything is
equal for a collection of advertisements to X, the RR will compute
it's IGP cost to each next-hop, and select the next-hop that it
is closest to. This path is then refl
sorry, i dont know mate :( not my strong point dude!
-Original Message-
From: Sam Sneed [mailto:[EMAIL PROTECTED]]
Sent: 31 January 2003 21:55
To: [EMAIL PROTECTED]
Subject: CCIE or a masters degree? [7:62287]
I was wondering, should I go for. haha fooled you.
If it takes trick
cont e1 0/0
framing crc4 | no-crc4
linecode hdb3
clock source line primary [is u have a 7000 and multiple E1's, the other
will be secondary]
line primary [if u have a 3600, 4000, AS5000, all other ports will
secondary]
pri-group timeslots 1-31 [if u want to use it all]
int se 0/0:15
configur
0a997d.shtml
""Firesox"" a icrit dans le message de news:
[EMAIL PROTECTED]
> Folks I am a little stuck in IRB config.
> I have two 2620 routers connected via T1.
>
> I would llike to route IP and bridge IPX.
> On the routed IP network I need to run OSPF to connect to other networks.
>
> I am loo
It's exactly as I have in my email earlier.
The only thing that I changed was:
#remove access-list 102 -not needed as ospf and other ip traffic is
inside the tunnel
#change access-list 199 referenced in the cryptomap:
RTA# serial ip = 120.20.26.2 255.255.255.0 tunnel ip = 120.20.59.2
255.25
Hi Buddy,
Can anyone tell me how to configure the port E1
controller on 7206 router.
Thanks & Regards,
Milind Tare
__
Do you Yahoo!?
Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
http://mailplus.yahoo.com
Message Posted at:
http:
In most cases you will only re-write the source mac address
when traversing
across a L3 device. If you go across a layer 2 network, all
the mac address's
would typically be part of the same broadcast domain and not
need to be changed.
If you go across a T1 or Frame it will still be mapped to or
ha
17 matches
Mail list logo