I have just done the same thing few weeks ago.
Make sure that you have the cables from PBX to E&M interfaces made by the
Cisco specification. You can get the wiring details from the 1700 Series
Hardware installation guide or the web.
Cheers.
_
FAQ, list archives
Go to:
http://www.galton.com/~cisco/
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
I think you should use Cisco Internetwork troubleshooting ISBN: 157800922
Cheers
Igor Glavanic
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Pass scores are between 690 and 710.
You will get between 63 and 65 questions.
Time allowed is 75 minutes as much as I remember.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations
the software from there as well.
I think your IOS must have letter "o" in order to support firewall.
Cheers
Igor Glavanic
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure vio
REAL Server ???
Real Networks Streaming Server or ???
If you talking about the obove, just give it normal IP address. Sofware on
the server should take care of the rest.
+
Configure routers for mulitcast
"thinkworker" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED
Make sure you DO NOT HAVE:
PPP MULTILINK or
DIALER LOAD-THRESHOLD ...
"kenny wong" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hi all ,
> There are 2 routers dialing to a single router's BRI
> line.
> The question is , WHen one of the dialing router call
Check your routing table.
You could have two routes to the same destination and one of them is not
working for some reason.
It looks like that
R1#ping 1.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.0.0.1, timeout is 2 seconds:
!.!.!
Success rate is 100 percent (5/5),
You can track your certification progress and requirements on the:
www.galton.com/~cisco
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Right...
Easiest is to use NAT.
Check BCRAN book or Cisco website on more info on NAT.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
have used them for CCIE
350-001 exam and how good they are.
Many Thanks
Igor Glavanic
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
I you had your CCNP in version 2.0, you could do only CID 3.0 and get your
CCDP.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
It is not the range -
that is reversed subnet mask
Example masks:
try with 255.128.0.0 mask will become 0.127.255.255
or 255.255.255.252 will become 0.0.0.3
So in your case the original mask of 255.255.252.0 thas changed to reverse
of 0.0.3.255
Cheers
Igor Glavanic
""Joe Arthur
Must have on lines
password
login
transport input all
create ip hosts with
ip host router1 2001 10.0.0.1 (your router ip addres)
Cheers
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosu
14 matches
Mail list logo