hi guys,
this is the output of my sh frame-relay pvc
DLCI = 171, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
Serial0/0.171
input pkts 1435560 output pkts 9358712 in bytes 370699089
out bytes 1069864391 dropped pkts 0 in pkts dropped 0
out pkts dropped 0
hi all,
we have one frame relay link to customer with the following connection
router -csu/dsu(lease line)frame relay node/cloud
the problem is on serial0/0(connected to csu/dsu) the input errors and
interface reset is increasing tremendously, ping test resulted in 6 packets
dropped
hi all,
I got one scenario, where we got 2 routers, one is A and another is HQ,
connection between A HQ are via Frame Relay and ISDN as a backup.
ISDN is using loopback address 202.x.y.z.
Question:
when both Frame Relay and ISDN are up,
how do I create access list in router A to deny ping to
Is there a way to know/test/monitor that ISDN backup is always ready to be
used when the primary link is down..? I sometimes frusrated that the ISDN
won't kick up when the primary link is down, and then only the ISP claim the
ISDN link got problem...
thanks
- Original Message -
From:
Hi guys,
need help to explain the output from 'sh int' below
1) what is 'underruns' and 'deferred' means..?
2)Is 'underruns' and 'deferred' indicate a router problem or a LAN problem..?
CustomerHQ1sh int faste0/0
FastEthernet0/0 is up, line protocol is up
Hardware is i82543 (Livengood),
hi all,
after i unshut the serial interface for frame relay service, the status was
up, up...but after a while(maybe 10 secs), it went back to up,down...and the
status up,up didn't represent the PVC is up because the Service Provider
always claim that their LMI status remained down during that
hi all,
i'm wondering is there a way we can manage an end-to-end connection on ATM
as what we have with LMI in FrameRelayTQ
rgds
nazri
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=51693t=51693
--
FAQ, list archives, and
hi all,
i can't ping to any host in the LAN although the fa0/0 shows up,up. sh int
fa0/0 described that there was a tremendous amount of interface reset, and
input rate is 0 what does it mean..? i did a shut/no shut on the the
interface fa0/0, then only i can ping to all LAN hosts...anybody pls
for
;
Sat, 09 Feb 2002 11:08:46 +0800
Date: Sat, 09 Feb 2002 10:58:33 +0800
From: Md Nazri
Subject: LAN IP address
To: [EMAIL PROTECTED]
Message-id:
MIME-version: 1.0
X-MIMEOLE: Produced By Microsoft MimeOLE V6.00.2600.
X-Mailer: Microsoft Outlook Express 6.00.2600.
Content-type
hi all,
we've monitored a slow frame-relay link to find out what causing that. we
found that 3% out of total frames transmitted are shorter than 64 byte(4~63
byte) and 0.1% are larger than 1024bytes. can anybody pls explain what this
result indicates...does it contribute to the slowness of the
i did sh buffer in a router and the o/p as below...anybody pls xplain what
does it mean.?
tq
nazri
Private particle pools:
1/0 buffers, 512 bytes (total 768, permanent 768):
0 in free list (0 min, 768 max allowed)
768 hits, 0 fallbacks
768 max cache size, 512 in cache
10
hi all,
i need to access a remote router via AUX port. Anybody pls clarify what i
should configure in my 2500 router and in my pc..
tq
nazri
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=20364t=20364
--
FAQ, list archives,
hi all,
how do i delete the sub-interface..? i tried using 'no sub#', but when i do
'sh ip int brie' it still give the sub# with status deleted...any help
appreciated
TQ
nazri
telekom malaysia
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7i=18346t=18346
that is maintained even if one of the routers fails. Your server will
maintain connectivity to available sites even if one of the routers fails.
Good luck, search Cisco.com for HSRP
Ejay Hire
-Original Message-
From: md. nazri [mailto:[EMAIL PROTECTED]]
Sent: Monday, May 21, 2001 11
hi all,
i got 2 routers sharing the same ethernet...both ether should active at the
same time(so i think hsrp not meaningful) with each ether have different ip
address with same subnet. Server on LAN should point to one particular
ip(can it be two..?)...how do i achieve that...?? pls help
hi all,
i got 2 routers sharing the same ethernet...both ether should active at
the
same time(so i think hsrp not meaningful) with each ether have different
ip
address with same subnet. Server on LAN should point to one particular
ip(can it be two..?)...how do i achieve that...?? pls
hi all,
got one question regarding FastEthernet on Cisco 2620..
why the status showed FastEthernet is up, Line protocol down although the
cable was pulled out from the port...in what cases the port will down..any
help appreciated
tq
Message Posted at:
At 08:21 PM 4/25/01, md. nazri wrote:
thanks for the answer...
i understand that LP will down if no connection attach, but why FE still
up,
does it up forever until we shut it down? Does it apply the same to
Ethernet..?
- Original Message -
From: Vincent Chong
To:
Sent: Wednesday
hi all,
i need some help on this,
2 routers connected over frame relay, named RouterA and RouterB. RouterA ethernet has
2 ip address, X(x,.x.x.x) as primary and Y(y.y.y.y) as secondary. RouterB ethernet
also has 2 ip address, W(w.w.w.w) and Z(z.z.z.z). X supposed to communicate only with
W
hi all,
I got a problem with my 2500 router, anybody pls
xplain what the (boot) means..i can't even
show my routing table...i copied sh ver o/p...
KB(boot)sh verCisco Internetwork Operating System
Software IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c),
RELEASE SOFTWARE
hi all,While doing troubleshooting on 3810 router, I got
this output when issue sh proc cpu command:
BKRB027RT120#sh proc cpuCPU utilization for five seconds: 99%/23%; one minute: 99%; five
minutes: 99%PID Runtime(ms) Invoked
uSecs 5Sec 1Min 5Min TTY
Process 1 38279
1093597 35 0.00%
21 matches
Mail list logo