Hello,
I tried to create a subinterface on s0 but i could not. Can any body tell me why?
Thanks
Omer
3102(config)#int s0.1
% Incomplete command.
3102#sh ru
Building configuration...
Current configuration:
!
version 11.3
service timestamps debug uptime
service timestamps log uptime
no servic
Omer,
Did you enter s0.1 ? <--- Once you entered the question mark you should see
the options to have either point-to-point or multipoint. Usually if you
receive an error such as yours % Incomplete command this is an indication
that more was expected. The question mark along with debugs will beco
Do a int s 0.1 ? and look at the output. There you will find your answer
HTH
Chuck
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] On Behalf Of Omer
Shommo
Sent: Sunday, June 11, 2000 10:27 PM
To: Cisco Group Study
Subject:Could not create
in oder to create subinterfaces in serial lines enter the following command
int s0.12 point
you must configure a point to point interface or multipoint connection in
order fot you to do this
type
int s0.12 ?
to find out more
PQ
"Omer Shommo" <[EMAIL PROTECTED]> wrote in message
[EMAIL
I'm not in front of a router right now, so I may be wrong, but...I believe
you need to be in interface config:
3102(config-if)#int s0.1
"Omer Shommo" wrote in message <[EMAIL PROTECTED]>...
>Hello,
>
>I tried to create a subinterface on s0 but i could not. Can any body tell
me why?
>
>
>Thanks
>
Hello Omer,
Are you using frame relay encapsulation on int s0? You can only create
subinterfaces in that encapsulation.
And consider the following: If you define a subinterface for
point-to-point operation you cannot reassign the same subinterface
number to be used for multipoint operation witho
Is this a frame relay interface? If so, then you either need
"point-to-point" or "multipoint" after the "int s0.1".
Notice that it didn't tell you it wasn't possible, just that your command
was incomplete. In a situation like this, type the command exactly as you
did before (or just hit up-arro
If you are using IOS 10.2 or before...it will not allow subinterfaces.
""Omer Shommo"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello,
>
> I tried to create a subinterface on s0 but i could not. Can any body tell
me why?
>
>
> Thanks
> Omer
>
> 3102(conf
Looks like to me he's using V11.3!
You can create a sub-interface...you just need to specify the type
afterwards! hit '?' after you type in the command, ie:
int s0.1 ?
-Brad
""Douglas James Howe"" <[EMAIL PROTECTED]> wrote in message
8it9tu$11u$[EMAIL PROTECTED]">news:8it9tu$11u$[EMAIL PROTECT
Are you using Frame-Relay?
-Original Message-
From: Douglas James Howe [mailto:[EMAIL PROTECTED]]
Sent: Thursday, June 22, 2000 10:14 AM
To: [EMAIL PROTECTED]
Subject: Re: Could not create subinterfaces
If you are using IOS 10.2 or before...it will not allow subinterfaces.
"
You also first have to set your encaps to frame-relay on the ser
interface...
-Original Message-
From: Douglas James Howe [mailto:[EMAIL PROTECTED]]
Sent: Thursday, June 22, 2000 8:14 AM
To: [EMAIL PROTECTED]
Subject: Re: Could not create subinterfaces
If you are using IOS 10.2 or
email,
facsimile or telephone and return and/or destroy the original message.
-Original Message-
From: Omer Shommo [mailto:[EMAIL PROTECTED]]
Sent: 12 June 2000 00:27
To: Cisco Group Study
Subject: Could not create subinterfaces
Hello,
I tried to create a subinterface on s0 but i could
4 AM
To: [EMAIL PROTECTED]
Subject: Re: Could not create subinterfaces
If you are using IOS 10.2 or before...it will not allow subinterfaces.
""Omer Shommo"" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> Hello,
>
> I
He's not using 10.2 or before, he's using 11.3
> -Original Message-
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of
> Douglas James Howe
> Sent: Thursday, June 22, 2000 10:14 AM
> To: [EMAIL PROTECTED]
> Subject: Re: Could not create subi
14 matches
Mail list logo
