$ for the Teak, plus shipping.
Bill Coleman
Erie, PA
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of David Risch
via CnC-List
Sent: Sunday, December 22, 2019 3:32 PM
To: cnc-list@cnc-list.com<mailto:cnc-list@cnc-list.com>
Cc: David Risch
Subject: Stus-List Teak
$ for the Teak, plus shipping.
Bill Coleman
Erie, PA
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of David
Risch via CnC-List
Sent: Sunday, December 22, 2019 3:32 PM
To: cnc-list@cnc-list.com
Cc: David Risch
Subject: Stus-List Teak Veneer...
Need to buy a 10"
I have some but I'm probably too far away. I just used some 1/8" teak
veneer to laminate onto plywood for a new electrical panel. The nice thing
about the 1/8" veneer is you can make it to any thickness you need by
bonding with plywood.
--
Shawn Wright
shawngwri...@gmail.com
S/V Callisto, 1974 C
Try Narragansett Shipwrights near the roundabout in Newport.
Andrew Burton
139 Tuckerman Ave
Middletown, RI
USA02842
www.burtonsailing.com
http://sites.google.com/site/andrewburtonyachtservices/
+401 965-5260
> On Dec 22, 2019, at 15:31, David Risch via CnC-List
> wrote:
>
> Need to buy
Need to buy a 10" x 25" sheet of teak veneer. Anybody have any left-over they
want to sell?
David F. Risch
(401) 419-4650
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want
it set
up, and then work the other side. The Super Glue has held for 6 years in
the Louisiana climate.
Ed
CC 30 Mk I Dreamgirl
CC 34 Acquired Today !
New Orleans
From: Roth Arthur rothassocia...@verizon.net
To: cnc-list@cnc-list.com,
Date: 11/06/2012 02:54 PM
Subject:Stus-List
I hope someone on the list may have a suggestion as to how to address/fix my
problem.
Sometime during the last month or so, water must have gotten into the boat
from the deck as yesterday while cleaning up below, I found several
blisters/delamination of the teak veneer on the upper far port
I think the iron method may work. The heat will soften the glue and the
iron would press it down. There is no way to clamp it flat on the wall. Good
luck-Bill Sterling
In a message dated 11/6/2012 3:54:23 P.M. Eastern Standard Time,
rothassocia...@verizon.net writes:
I hope someone on
If it was my boat, I think I'd try to inject glue (waterproof Titebond? or
epoxy) into the blister with a syringe. You can buy glue syringes at Lee Valley:
http://www.leevalley.com/en/wood/page.aspx?p=20003cat=1,110,42967ap=1
But I suspect they're available all over - Harbour Freight? as your in
Fred Hazzard
S/V Fury
CC 44
Portland, Or
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Roth
Arthur
Sent: Tuesday, November 06, 2012 12:54 PM
To: cnc-list@cnc-list.com
Subject: Stus-List Teak Veneer Delamination
I hope someone on the list may have a suggestion as to how
10 matches
Mail list logo