I'm starting to get the bug to try something different and EME has
grabbed my attention.
I already have a couple K3's and would like to put one to use for EME.
Which is the better option the external 144mhz transverter or the
internal 2m option?
Thanks
Rich - N5ZC
Another post here since I'm sure support is closed till Tuesday and I'm
hoping to make some progress over the long weekend.
Pg 51, the very last step, is the install of C167 (.001 uF, 102).
Appendix A shows a more or less photo of this capacitor.
I can't locate this capacitor, but then, I may
Yes, use the .001 uF (marked 102) at C167.
Yes, you will have to bend the leads straight out and then form them
again at a right angle to fit the hole spacing.
Those yellow capacitors are also monolythic, and yes, they do not look
like the picture.
73,
Don W3FPR
On 8/30/2014 5:06 PM, Lane
The K1 I offered for sale has been sold.
John K7JLT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
This is why the inventory at the start of the build is so important -- you
identify all the parts, and in cases of doubt you can sometimes use a process
of elimination to work out which part is which.
For C167, I removed it from my radio when I installed the SSB module. Here is a
picture of
Heh, goes to show how much I know about electronics. Thank you both, I had
to step away from my build for a month and didn't recall much of my
previous 102 work.
Thanks again.
On Sat, Aug 30, 2014 at 5:01 PM, Matt VK2RQ matt.vk...@gmail.com wrote:
This is why the inventory at the start of the
Hi folks,
I'm working on my XV432 kit this weekend. I ordered the high accuracy
crystal and the crystal oven options as well. I'm on page 31 of the
XV432 manual, where it is asking me to locate L4 and L19 for
installation. I see that L19 appears to get replaced when installing
the high
I have for sale K3/100 S/N 6448 which includes KAT3 ATU Modular kit, KXV3A
RX Ant., IF Out and Xverter Interface, 2.8kHz fo 2.7kHz swap, KFL3A 400
Hz 8 pole filter and PR6 6M Low Noise Pre-Amp. This was a kit bought in
April 2012 ($2800) and has worked perfectly since I finished it. (I am a
Gents,
I have a lot of Elecraft Y cables and lots of things going on and I would
like to make firm those connections between my 15 connectors and the double
Y connectors. I am thinking there must be a name for those double nuts that
could screw between connectors and also a source for a little
Happy days!
The replacement choke came today, and I promptly installed it. I'm now getting
7.85 volts at the D2 and D3 anodes, and much stronger signals across all bands.
Picked up several S-9 signals, and even a couple that that were S-9 +10.
I also completed the installation of the KAT2
On Sat, Aug 30, 2014 at 4:25 PM, William Levy wgl...@gmail.com wrote:
I have a lot of Elecraft Y cables and lots of things going on and I would
like to make firm those connections between my 15 connectors and the double
Y connectors. I am thinking there must be a name for those double nuts that
Ken,
If you have a recent XV432 (within the past 2 months), it is being
shipped with the High Accuracy crystal.
Look at the markings on the crystal that came with the XV432, and
compare it with the crystal shipped with the High Accuracy Kit - if it
is the same, you can put either crystal in
-- Forwarded message --
From: William Ewing w...@goldtel.net
Date: Sat, Aug 30, 2014 at 6:32 PM
Subject: FS: K3/100 S/N 6448
To: Elecraft@mailman.qth.net
I have for sale K3/100 S/N 6448 which includes KAT3 ATU Modular kit, KXV3A
RX Ant., IF Out and Xverter Interface, 2.8kHz fo
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list:
Google jack screws
On 8/30/2014 6:25 PM, William Levy wrote:
Gents,
I have a lot of Elecraft Y cables and lots of things going on and I would
like to make firm those connections between my 15 connectors and the double
Y connectors. I am thinking there must be a name for those double nuts that
The weekly Elecraft SSB net meets Sunday at 1800Z on 14.3035 MHz. Stop by and
say hello.
73,
Phil, NS7P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
Hi Dan,
Wow! That's a lot of money to spend only to find I don't need the darn
thing! I'll be talking to Elecraft about that next week.I ordered
both about 3 weeks ago. Thanks for letting me know. I appreciate it!
73,
Ken
On 2014-08-30 9:04 PM, Don Wilhelm wrote:
Ken,
If you have
Don...not Dan! Sorry!
Ken
On Aug 30, 2014, at 10:30 PM, Ken Alexander k.alexan...@rogers.com wrote:
Hi Dan,
Wow! That's a lot of money to spend only to find I don't need the darn
thing! I'll be talking to Elecraft about that next week.I ordered both
about 3 weeks ago. Thanks
Good Evening,
Rain started slowly this morning and continued all day. Not much
overall but the forest smells much better. There is a spicy scent in
the air, I imagine it is from all the cedar in the ground. After a warm
to hot week these cooler days feel nice but presage autumn. So I
19 matches
Mail list logo