Hi Dana,
I would check the coax you are using. Or try another coax. Looks like you
checked the dummy load.
My KX3 did the same thing several months, had a bad fitting on the coax
jumper.
73
Jim H
K7SSS
In a message dated 12/27/2015 4:54:57 P.M. Pacific Standard Time,
elecraft@mailman.qth.ne
The firmware is up to date (MCU 2.34, DSP 1.33).
I have done a TX gain calibration and the SWR indicator is still reading
as before.
Dana Browne, AD5VC
On 12/27/2015 7:15 PM, Walter Underwood wrote:
What version of firmware are you running?
I’d update the firmware and run a TX gain calibrat
What version of firmware are you running?
I’d update the firmware and run a TX gain calibration with the KX3 Utility.
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On Dec 27, 2015, at 5:10 PM, Dana Browne via Elecraft
> wrote:
>
> Oops, pressed enter too soo
Oops, pressed enter too soon.
I neglected to mention that the only additional board I have in the KX3
is the antenna tuner, I do not keep batteries in it, and the serial
number is #150, so a rather early model. I was unable to find anything
in the KX3 manual about the SWR meter, but I recall
I have noticed on my KX3 that the SWR indicator gets progressively less
accurate on the higher bands. I have the antenna tuner installed, but
when I put it on bypass, I see into a 50 ohm dummy load
15m 1.2
12m 1.4
10m 1.5
6m 2.1
I have used two homemade dummy loads and one commercial one, an
> If the KBPF3 modification compromises performance elsewhere in the
> coverage, I might be better off using my current approach: A
> home-brew transverter for 630m coverage with a 10.0 - 10.5 MHz IF
> with home-brew sharp cut off low pass filter ahead of the RF input.
The KBPF3 modification im
I am considering the Elecraft modification to the KBPF3 for 630m coverage on my
K3. Is there any information published on the band pass filter performance
before and after the modification?
If the KBPF3 modification compromises performance elsewhere in the coverage, I
might be better off using
Good Day,
After a rain induced power outage of 28 hours I had a respite of two
days. Then there was a power outage of 62 hours. Now the power is more
stable with only short outages but I am waiting for the next boot to
drop since the snowfall is getting heavy. Trees are snapping and
poppi
That I'll buy. I knew it was more than tapping the Display button.
Sent from my iPhone
...nr4c. bill
> On Dec 27, 2015, at 11:38 AM, Alan wrote:
>
> To have waterfall enabled on the external display and off on the internal
> display, or vice versa, requires three things:
>
> - P3 firmware 1
Thanks Don -
I made the change on all bands, and now the P3 displays the same on all
bands.
73
-Ferris NB6T-
-Original Message-
From: Don Wilhelm [mailto:w3...@embarqmail.com]
Sent: Saturday, December 26, 2015 3:15 PM
To: Ferris Jennings; elecraft@mailman.qth.net
Subject: Re: [Elecraft] P
The K312MDKTs have been spoken for. I still have one KIO3A. The other went
for $50 shipped.
73, Ken, K6LA / VY2TT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq
To have waterfall enabled on the external display and off on the
internal display, or vice versa, requires three things:
- P3 firmware 1.50 or later
- The "SVGA WfEn" menu entry set to either "Waterfall on" or "Waterfall
off" as desired.
- Toggling the DISPLAY key on the P3 to turn on/off th
I was able to set the levels on my Asus Xonar U5 under El Capitan usingthe
Audio MIDI Setup app (found in the 'Other' compartment on the firstpage of the
App Launcher). I run the Mac OS X version of WSJT-X nicely,although I do fire
up Parallels 11 and Windows 7 Home Premium to run HRD.
There ARE
Hi all,
The SVGA WfEn toggles the SVGA waterfall on and or or tracks the P3's main
display. So you can set it on and the turn the P3 on and off independently.
That's how I have mine set up.
Cheers and 73,
Fred KE7X
For all KE7X Elecraft books see www.ke7x.com
___
Joel,
I am using the TASCAM US-366 with both my K3 (dual receiver in diversity mode)
and KX-3. I am running multiple instances of WSJT-X (rev 1.6). The TASCAM
US-322 should work well also. Both are available at Amazon.com. TASCAM provides
drivers for OS-X.
I believe newer models of these are t
Line 1 and Line 2 are the Neutrik connectors and I *think* stereo
(someone please correct me if I’m wrong) which would allow you to
hook up the way I’m thinking.
After tracking down a manual on the 2i2 it looks like Line 1 and
Line 2 are two *mono* channels. You could connect one radio. If
y
No
On Sat, Dec 26, 2015 at 10:03 PM, Alan wrote:
> On 12/26/2015 06:23 PM, Ken Widelitz wrote:
>
>> The bottom of page 30 of the P3 manual shows a photo with the waterfall
>> What I would like to
>> accomplish is have the waterfall on the SVGA monitor, but not on the P3
>> display. Is that possi
In addition to the previous reply ... assuming your intent is to switch
between the front mic and Line In (Macro 1 selects the mic, Macro 2
selects Line), you do not need *three* UP;/DN; commands ... only two.
The extra commands should not be an issue. However:
Macro 1: MN053;DN;DN;MN255;
Ed et al.,
I use OS X and have been looking at an upgrade from my E-MU 0204. This device
is no longer available from Creative Labs and doesn’t appear to be supported
any longer either.
I have been looking at the Focusrite 2i2 and trying to compare specs of it with
the E-MU 0204. Without having
Hello elecrafters,
I have two old KSYN3 after I installed the new one in my K3. If you would like
to take them, all you paid is the shipping postage.
If you are interested, please contact me off-the-list.
73
Johnny VR2XMC
__
Elecraft ma
20 matches
Mail list logo