Searching for previous Elecraft postings is very possible. Here are several
ways:
https://marc.info/?l=elecraft
https://www.mail-archive.com/elecraft@mailman.qth.net/maillist.html
http://elecraft.365791.n2.nabble.com/
John KK9A
KM3K wrote:
Hello, I get the condensed version and usually
Please disregard my earlier post. A ham quickly replied off-line with the
answer. I am getting the info I wanted. 73 jerry km3k
Sent from my Samsung Galaxy smartphone.
Original message From: jsodus Date:
8/9/18 19:27 (GMT-05:00) To: elecraft@mailman.qth.net Subject: Search
Hello, I get the condensed version and usually delete the email when I've read
it. Ditto for the kx3 group too.I now want to re-read postings done earlier
this year relative to "single-paddle vs dual-paddle use".I do not know how to
do a search or if it is even possible.TIA for any help.Jerry
Thanks for the heads-up Dave - got him on the first call with 100 watts to a
doublet at 45 feet!
73, Jim / W6JHB
Folsom, CA
> On Aug 9, 2018, at 2:44 PM, Dave G. wrote:
>
> EA3 (Barcelona) looking for W6/W7 around 14.22
>
> Dave G.KK7SS
> Richland, WA.
>
EA3 (Barcelona) looking for W6/W7 around 14.22
Dave G.KK7SS
Richland, WA.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
"It also seems like this fan logic could be built into the KPA1500 firmware if
the result is a quieter and cooler amp. on receive."
Actually it seems as though Elecraft chose to go the other way - delay the fan
speed increase until a higher temperature. See KPA1500 firmware release notes:
Hi Bob
"During Tx, override fan menu settings and run at settings +1"
(Not sure what this means, run fan at 2 when it normally would be at
1?)
Yes, that is exactly what it means. The assumption being that you would
rather hear the fans when transmitting (said the RTTY / FT8 guy ...)
than
HiNo the span is supported but not the zoom in the amplitude directionPlease
take a look at the video on how to use the spectrum scope under documentation,
video tutorials on my website.In general the mouse is used to zoom in and the
actual baseline will change day by day and even by hour, so
Hi, I am evaluating Win4K3, and trying to program spectrum macros to make
initial setup quicker after program restarts. I am able to change the span
without a problem, but I would like to set the scale as the default is too
large.
I tried %SCL080 to scale to 80dB with no luck.
Is this maco
Or use AM SYNC mode ..
Grant NQ5T
K3 #2091 KX3 #8342
> On Aug 9, 2018, at 1:54 PM, Don Wilhelm wrote:
>
> Wolfgang,
>
> The width displayed is the audio width. An AM signal has 2 sidebands, so it
> is twice as wide as the audio frequency displayed.
> If you want to listen to AM in a 1.35
Wolfgang,
The width displayed is the audio width. An AM signal has 2 sidebands,
so it is twice as wide as the audio frequency displayed.
If you want to listen to AM in a 1.35 kHz width, then it is possible,
but there will be few highs, and will likely not be intelligible.
You can use SSB
Hello:
Installed a 6 Khz AM-filter and have the following problem:
Filter slot 1: 6Khz Filter
Filter slot 2: 2.7 Khz Filter
Both of the filters are configurated as receive filters for AM mode.
When I switch from filter 1 to filter 2 in AM mode the filter 2 (2.7
KHz) is shown in the display
FANticipator GUI has two checkboxes:
"During Tx, override fan menu settings and run at settings +1"
(Not sure what this means, run fan at 2 when it normally would be at 1?)
"After Tx, override fan settings and run at #1 until below 40c"
I assume it doesn't try to do fan adjustment when
I have for sale an Elecraft P3-F Panadapter. It is approximately 2 years
old, I am the second owner and it comes from & is presently in a nonsmoking
environment.
It includes the following and I will *NOT* piece it out:
P3-F Panadapter, Assembled for K3S, K3 and other rigs
P3TXMON TX
I have for sale an Elecraft K3 – F, serial #5946, that has served as my
backup radio. I am the second owner and it came from and has been in a
non-smoking environment. It works 100% and appears 9.5 out of 10, as the
LCD Bezel has two cracks in the corner (it came that way from the previous
FANticipator is a freeware KPA1500 console and enhanced fan controller
that I've developed to maximize shack silence and minimize fan noise.
My selfish intentions are based on the following:
You prefer to have the fans automatically shut off completely when the
amp nears ambient temperatureYou
The amp arrived in fine shape and am getting familiar with all the
features. I have some questions:
Is there an input attenuator normally in-line?
I can't figure out how to manually change the L and C values for the tuner.
If these are changed, are the settings memorized?
73, Roger N1RJ
I recently bought a K3S and it came with several items I will never use, so
I am slowly getting rid of them.
First up is an Elecraft KPOD serial #4474 it is approximately 2 years old
and looks & functions as new. I have the original box and cables.
Asking $210.00 plus shipping from 44130
73 de
Bill,
Have you looked at the RS232 menu to check the baud rate?
If you have a P3 check that too.
Set it for 38400.
73,
Don W3FPR
On 8/8/2018 4:34 PM, Bill wrote:
Suddenly, HRD is no longer working with my K3:
Using my K3, I initially click on a favorite - the rig responds
immediately. After
I have five filters in my main receiver and only two in my subreceiver .
Only 400Hz filters are common in both. I have the identical setup in two
separate K3S's and it works great for my HF contesting needs where I use
the sub for SO2V. If you want to use diversity reception you may want at
least
Hi,
I too have had issues with the serial port speed of my K3 as well. My
issues are when using MixW though, not HRD. When I switched from my
Icom 756 PROIII to the K3, (using MixW), I was appalled at the loss in
speed for rig control. I have never fully resolved this issue, and will
be
21 matches
Mail list logo