Jim,
My usual procedure when tackling a problem of that nature is to first
isolate the problem to one component.
You have already apparently checked out the base K2.
Next, remove the top cover from the base K2 and connect the KPA100 to it
(remove the KPA100 from the EC2 enclosure).
Put the KP
I tried to tune the KPA/KAT100, and the SWR went to red. I quickly exited
'tune', checked all of the connections, and the antenna, and tried again. Same
result, except before I could take it out of tune (it was tuning maybe 2-3
seconds), all of the KPA/KAT100 lights went out. The K2 was fine. I
We had a 38 check ins for the net today. I want to thank everyone for
participating and dealing with some difficult propagation. Thanks to the relay
stations for your help as well
Elecraft SSB Net 2-3-2019
WB9JNZ Eric IL K3 4017 Net control
NS7P Phil
Good Evening,
Compared to last week Fargo, North Dakota is undergoing a heat
wave. It's up to 0 degrees Fahrenheit :) Iowa has dense fog and
sauna-like temperatures in the mid 40s. My brother in SW Wisconsin
reported a flood just west of his barn. His Mangalitsa and mulefoot
pigs are
The twenty meter net went rather well. Once I had a chance to call the
net I was met by a solid tone which is always a good sign. The
tail-enders get a break. By being a second after the solid tone I can
get letters from your callsigns. Signal reports all had some QSB but
ranged from S1 to
Greetings to All,I am looking for a KX2 in good operating and cosmetic
condition. Let me know what you have.73MarkKK2L
-
Mark
KK2L
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qt
I would again like to extend a thank you to all replied. I have for sure
learned a lot about sending a rig for repair overt the boarder.
Thanks again for all of you who took time to reply!
73,
Mike
VE3WDM
--
Sent from: http://elecraft.365791.n2.nabble.com/
Bill,
When you need to send it in for repair, email supp...@elecraft.com
asking that an RSA be issued.
Explain that you bought it used.
You should also include your K3 serial number and your contact
information in that same email.
73,
Don W3FPR
On 2/3/2019 2:13 PM, 1lasportsman 1lasportsman
Mike,
Of some concern is the heating of Q6 - but I don't think it is
unreasonable if you can still hold your finger on it.
Hint for troubleshooting. *IF* the problem is in the RF amplification
chain (Q5 thru Q8) then it should appear in TUNE as well as in SSB.
I would suggest that you measur
Don
Where do I do that?
> On February 3, 2019 at 1:09 PM Don Wilhelm mailto:donw...@embarqmail.com > wrote:
>
>
> Bill,
>
> There is not any requirement to register it with Elecraft.
>
> However, if you need to send the K3 for service, you will want to make
> sure that serial
Bill,
There is not any requirement to register it with Elecraft.
However, if you need to send the K3 for service, you will want to make
sure that serial number is updated with your contact information.
73,
Don W3FPR
On 2/3/2019 1:52 PM, Bill wrote:
Do I need to register with Elecraft a purc
Do I need to register with Elecraft a purchase of a used K3.
IF I need to please tell me where to register it at, looked on website and did
not see where.
Thanks
Bill
WF9M
Sent from Mail for Windows 10
---
This email has been checked for viruses by Avast antivirus software.
https://www.avast.c
Hello All,
I have a KX3 and PX3 set for sale. There are lots of options included. A
few options are nifty stands, side rails, from covers, heat sink, cw
paddle, signal link USB, Side Kar, and a custom aluminum base that holds
all of it. Unit has been back to Elecraft for calibration and alignm
I heard nothing. Band is flat here in NE WI.
73,
Bill
K9YEQ
https://wrj-tech.com/
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of 1lasportsman 1lasportsman
Sent: Sunday, February 3, 2019 12:29 PM
To: Phil Shepard ; RALPH TURK
Cc: elecraft@mailman.qth.net
Subjec
Tied to check in for first time and here in Louisiana I was unable to hear
enough to tell what was being said.
Made one call but got no response
Bill
WF9M
> On February 3, 2019 at 10:26 AM Phil Shepard mailto:ph...@riousa.com > wrote:
>
>
> Sundays at 1800Z on 14.3035.
>
> > > On
Mike,
Is there any chance you have the K60XV option in that K2?
If so, you can set split the transmit path into 2 pieces because the
Transverter output takes its output from just after the bandpass filters
- i.e. - it does not use the Q5, Q6, Q7 and Q8 stages.
Set up for a transverter band op
Sundays at 1800Z on 14.3035.
> On Feb 3, 2019, at 6:23 AM, RALPH TURK wrote:
>
> What time & Freq is the Elecraft SSB net on?
>
> Ralph,W7HSG
>
>
> 520-444-6610
>
> Ralph S. Turk,
>
>
>> On February 2, 2019 at 10:51 PM kevinr wrote:
>>
>>
>> Good Evening,
>>
>>Tomorrow we are due
Maybe something in this thread will help.
http://elecraft.365791.n2.nabble.com/K2-SSB-Performance-Improvement-td7596200.html
73,
George NC5G
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mai
What time & Freq is the Elecraft SSB net on?
Ralph,W7HSG
520-444-6610
Ralph S. Turk,
> On February 2, 2019 at 10:51 PM kevinr wrote:
>
>
> Good Evening,
>
> Tomorrow we are due for a snow storm. Somewhere between six and
> eight inches before it ends. Hopefully it will not effect
RVerzonden vanaf mijn Samsung Galaxy-smartphone.
--4e-- Oorspronkelijk bericht Van: Jim Brown
Datum: 03-02-19 14:30 (GMT+08:00) Aan:
elecraft@mailman.qth.net Onderwerp: Re: [Elecraft] Tx distortion On 2/2/2019
7:54 PM, Bob McGraw K4TAX wrote:> Don't forget about the length of the
20 matches
Mail list logo