Re: [Elecraft] Does the KX2 have Squelch?

Thanks Mike and I have Squelch working. Paul > On Jul 6, 2019, at 8:07 PM, Michael Walker wrote: > > You have to be at the following revision: > > > Rev. A6-2, 15 December, 2017 Copyright © 2017, Elecraft, Inc. All Rights > Reserved > > FM Mode FM Mode > > This added mode is intended

[Elecraft] KPA500 Problem

For Doug, K6JEY: In answer to your original question, as to whether you should look into the KPA500's low voltage values: Yes. By far, the best advice and the best answers on this particular question will come from emailing supp...@elecraft.com . By far. Once the voltage questions are add

Re: [Elecraft] KPA500 Problem

I did look at the parameters of my KPA500 this morning.  In STBY the HV is 75.4 and in OPER at 500 watts out, CW mode, key closed the HV is 63.7 and current is 10.5 amps.   Amp is operated from a 240 volt source. 73 Bob, K4TAX On 7/7/2019 6:20 AM, Mark Murray via Elecraft wrote: For Doug, K

[Elecraft] KPA500 Problem

"I have a KPA500 with a low HV reading. It is on the center tap and AC voltage is 115v No load and 110v full load. The HV goes from 77v NL to 56v FL (500W output) Is that something I should look into? " The KPA500 high voltage (nominal 60 volt) power supply is unregulated. The mains power

Re: [Elecraft] Fwd: K4/K4D antenna ports.

I'm not always the best at reading between the lines. With and without the internal antenna tuner, how many ports are available for Transmit? As ever, Dick - KA5KKT Nr4c < nr4c at widomaker.com> wrote: >> How many ports does a K

[Elecraft] KX2 Display

I have owned my KX2 for some time now. I am now just now getting it on the air. I have a problem that I can not resolve. I have spent a few hours attempting to do that. When I try to bring up the DISPLAY function it does not work. The same button when held does work. Just the DISPLAY does not resp

Re: [Elecraft] Fwd: K4/K4D antenna ports.

3 with, 1 without. Wayne elecraft.com > On Jul 7, 2019, at 7:16 AM, Dick Dickinson wrote: > > I'm not always the best at reading between the lines. With and without the > internal antenna tuner, how many ports are available for Transmit? > > > > > > As ever, > > Dick - KA5KKT > >

[Elecraft] K2 REC/MEM is OK, I was the problem.

I have been using my cootie so long that I forgot it was a cootie. I have a Bengali paddle that I jumped to make it a cootie to use on my K2. I had changed the menu setting to hand. Well, when I tried to update my memory in button #6 for use with the 13 Colonies event, my radio was ignoring m

Re: [Elecraft] K2 PLL reference oscillator problems (DAC side!)

My K2 was having this same issue with the PLL test. I replaced the Q19 J310 with one on hand and it fixed it. Should I replace all the J310 in my kit, and option kits, or are the sub-par J310 only a problem in the PLL circuit? -- Sent from: http://elecraft.365791.n2.nabble.com/ _

Re: [Elecraft] K2 PLL reference oscillator problems (DAC side!)

Ryan, Those sub-par J310s should work in all other circuits in the K2. The only other possible exception is Q18, but if you can successfully run CAL PLL, then all should be OK at Q18 as well. The problem J310s at Elecraft was resolved early this year and the incidences of this problem should

Re: [Elecraft] Fwd: K4/K4D antenna ports.

I believe the answer is One for K4(D) without ATU. You get two others with ATU. Sent from my iPhone ...nr4c. bill > On Jul 7, 2019, at 10:16 AM, Dick Dickinson wrote: > > I'm not always the best at reading between the lines. With and without the > internal antenna tuner, how many ports are

[Elecraft] Elecraft SSB Net for Sunday June 30 and July 7, 2019

With our Net Control Station Eric WB9JNZ preparing for a two week overseas trip he asked me to get us caught up on the Elecraft SSB Net postings. Propagation remains challenging and our relay stations continue to make a huge contribution. Special thanks to all the relay stations noted below.

[Elecraft] K3: Update - Antenna not connecting on change to BC frequencies

Initially posted 6/5/19, now solved. The problem was signal intermittency with an installed KBPF3 when switch to frequencies below 1.700. With patient help from Keith WE6R at Elecraft and suggestions from 5 other list members I was able to confirm the problem was on the KBPF3 board.

[Elecraft] Elecraft CW Net Report

Good Evening,    Roy, K6XK, mentioned not having any earthquakes this week. During my formative years in Wisconsin I had never felt one.  Then in 1972 or '73 the New Madrid fault in Missouri let loose. Instead of working on chemistry problems I was reading Ambrose Bierce in my third floor room

Re: [Elecraft] KX2 Display

Jim - I'm not sure this will help but here goes I have KX2 SN 11xx with current firmware loaded:  uC 2.89, DSP 1.52.  I've reviewed all the update information and there doesn't appear to be any changes that would modify the behavior of the DISP function.  Mine works as described on page 2