Re: [Elecraft] KXBC3 question

2019-10-13 Thread Grant Youngman
The LO SUPPLY message indicates the power supply is delivering less than 13.8vdc at the KX3. Can you adjust your supply voltage a bit higher? Grant NQ5T KX3 (8342)/KXPA100 > On Oct 14, 2019, at 12:10 AM, Eddy Avila wrote: > > My KX3 is about 2 years old, recently I set he The KXBC3 to

[Elecraft] KXBC3 question

2019-10-13 Thread Eddy Avila
My KX3 is about 2 years old, recently I set he The KXBC3 to 16hr charge and powered down the KX3 and everything looked normal. However, a few hours later I noticed the Lo-Supply message was flashing on and off, but when I checked the KX3 was getting 13.61vdc and I believe charging was still

Re: [Elecraft] KX3/KXPA100 POWER ISSUES

2019-10-13 Thread Igor Sokolov
You can also monitor the voltage on the readout of your KX3. 73, Igor UA9CDC 14.10.2019 3:23, Bob N3MNT пишет: This can happen if you have a poor power connection to the KXPA and the input voltage drops. Use the KXPA utility to check the input voltage during tx. -- Sent from:

[Elecraft] Elecraft CW Net Report

2019-10-13 Thread kevinr
Good Evening,    Conditions are holding at less than desirable.  QSB was less which normally means the sun is quiet.  The lack of signal strength enhanced that assessment.  Twenty meters was shorter this week.  Normally California is too close.  But Texas and Nevada on forty meters was a

Re: [Elecraft] K4 waterfall

2019-10-13 Thread Nr4c
If you look thru the K4 FAQ, you’ll notice there’s an HDMI port on the back. Sent from my iPhone ...nr4c. bill > On Oct 13, 2019, at 12:46 PM, Wayne Burdick wrote: > > Yes. > > Wayne > N6KR > > > elecraft.com > >> On Oct 13, 2019, at 5:56 AM, Ken Chandler wrote: >> >> Hi guys >>

[Elecraft] SWR meter on SSB

2019-10-13 Thread Rich
I am noticing that my SWR meter flickers a bit during SSB transmissions.   I have no indication of RF getting into my signal.   I have checked with several folks and they say may audio is great and no indication of RF on the audio.   I have RF Detect turned on an I never get an error from that

Re: [Elecraft] KX3/KXPA100 POWER ISSUES

2019-10-13 Thread Bob N3MNT
This can happen if you have a poor power connection to the KXPA and the input voltage drops. Use the KXPA utility to check the input voltage during tx. -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] Question for California Hams

2019-10-13 Thread Phil Kane
On 10/12/2019 11:30 AM, WW3S wrote: > Half truthwell maybe 1/4 truthone, repeat ONE, repeater owner > got a letter from a tower he was on, but didn’t own, that he would be > charged rent going forwardhe didn’t like it, and started all this > crapno “officials” declared that ham

Re: [Elecraft] K4 waterfall

2019-10-13 Thread Wayne Burdick
Yes. Wayne N6KR elecraft.com > On Oct 13, 2019, at 5:56 AM, Ken Chandler wrote: > > Hi guys > On the new K4, is there a built in facility to protract the waterfall onto a > large PC screen! > > Cheers > > Ken.. G0ORH > > Sent from my iPad > > >

Re: [Elecraft] Blasphemy maybe but looking for an honest assessment of the K2 vs. Icom 7300 ...

2019-10-13 Thread Don Wilhelm
Randy, Since you will be using the K2 with the KPA100, you need to strongly consider adding to the list of upgrade mods shown on the K2 A to B instruction sheet the K2 Keying Waveshape mod. It is important to keep the keyclicks down. They are not obvious with the 10 watt K2, but rear their

Re: [Elecraft] XG50 power on aging cycle

2019-10-13 Thread Mike Parkes
Thanks Don, in that case I may just leave it as is! 73, Mike AB7RU On Sat, Oct 12, 2019, 1:42 PM Don Wilhelm wrote: > Mike, > > As the instructions indicate, you only have to do it once. > That is for initial aging of the crystal. > > If you are getting only 1 Hz drift on 40 meters, note that

[Elecraft] K4 waterfall

2019-10-13 Thread Ken Chandler
Hi guys On the new K4, is there a built in facility to protract the waterfall onto a large PC screen! Cheers Ken.. G0ORH Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help:

Re: [Elecraft] Blasphemy maybe but looking for an honest assessment of the K2 vs. Icom 7300 ...

2019-10-13 Thread Randy Heise
Thanks to all for your well considered replies, both on and off line. I had pretty much decided to do the Rev A/B mod to my K2 and keep it for QRP and the 5th Wheel and purchase the 7300 for the base station. Then, one of our members offered a KPA-100/KAT-100 in an EC-2 enclosure at a very