Is there a listing of K3 error codes available? They don’t appear to be in the
manual.
Dave K9SW
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
I fairly regularly listen for the net but never heard anything until last
Sunday. Steve, K4JPN had a nice signal into the Chicago area.
Dave K9SW
> On Sep 24, 2023, at 9:26 PM, kevin wrote:
>
> Good Evening,
>
>Twenty meters had decent signals with some QSB and a few strong storms.
>
Rob, do they specifically forbid HF radio transmission? I live in a small (21
unit) condo building near Chicago, and the association is kind enough to let me
put a Hustler antenna with three resonators on our first floor balcony. It
works but OK not great. If you’re on a higher floor, you
Numbers using the Elecraft 20 watt dummy load rather than resonated antennas:
40 M 4.8 W
30 M 5.5 W
20 M2.0 W
15 M1.7 W
Dave K9SW
> On May 11, 2023, at 6:52 PM, DAVID MOORMAN wrote:
>
> I have a K1 that I’m looking to sell, and took a look at the power output
I have a K1 that I’m looking to sell, and took a look at the power output
before listing it. Power output is as follows:
40 meters 5.2 watts
30 meters 4.5 watts
20 meters 1.3 watts
17 meters 0.7 watts
These are obviously not the expected power output levels. Power supply voltage
= 12.8
A 123 AH BioEnno Battery would cost nearly as much as a KX3!
Dave K9SW
On 10/10/21 7:27 PM, Geoffrey Feldman wrote:
Understand you don't want an amplifier, go QRP.
Nothing wrong with the switcher or with the Pro Audio.
What I am happy with is the BioEnno is the BioEnno 123AH battery. It's
The clicking relay turned out to be in an amplifier keying circuit a
previous owner had installed.
Problem solved!
Dave K9SW
On 7/25/2021 5:51 PM, k...@comcast.net wrote:
Thanks, Don. It’s a K2/10, so I’ll do the relay touch-test.
Dave K9SW
On Jul 24, 2021, at 8:40 PM, Don Wilhelm
Try turning VFO NR to ON.
Dave K9SW
On Dec 18, 2012, at 5:05 PM, zen...@netspace.net.au wrote:
Hi Group,
FWIW, I have an observation about the KX3 VFO tuning noise.
I assembled my #2511 (absent any options) from the kit. Over
a month of use, I noticed the raspy
The specs say the KX3 current draw is typically one to two amps when
transmitting, so your 2.89 amp PS should do fine.
Dave, K9SW
On Sep 18, 2012, at 3:53 PM, Bill Tubbs cgpi...@yahoo.com wrote:
After sending my note about using the little MFJ power supply at 2.89 amps, I
realized that
Do you have a receiver you can listen on to see if the oscillator is actually
oscillating?
Dave K9SW
On Jul 3, 2012, at 6:41 PM, Cameron Haines camhai...@yahoo.com wrote:
Correction.
Hey Guys,
Well, I am at the part where I need to test the 4 MHz oscillator calibration
and ran
Everything is working well. Beautiful piece of gear!
I had to wait for three 1/4 4-40 spacers to finish it completely but got it on
the air without them. They came to the Midwest via Honolulu, so it took a few
days
First QSO - 4O3A, Ranko in Montenegro, on 20 meter CW.
Now - onward to
Everything is working well. Beautiful piece of gear!
I had to wait for three 1/4 4-40 spacers to finish it completely but got it on
the air without them. They came to the Midwest via Honolulu, so it took a few
days
First QSO - 4O3A, Ranko in Montenegro, on 20 meter CW.
Now - onward to
12 matches
Mail list logo