Re: [Elecraft] KPA500 PA DISS fault

I had the same problem about a year ago.  It's a problem with the output PIN diode switch. There will be a burned toroid in the output switch circuit. I sent mine back for repair. It's been working fine since.Good luck,Glenn WB5TUF  Original message From: Rajiv Dewan Date:

Re: [Elecraft] [BVARC] Elecraft P3 BLACK SCREEN but not DEAD

I had the same problem with mine a while ago. The problem was with the 3.3-volr regulator module. It would get very hot and stop working after a few minutes. There are two regulator modules on the input board. A 5-volt and a 3.3-volt. They are the thick, black, edge-mounted things on the board. If

Re: [Elecraft] K3s USB sound card problem

Make sure that you have the K3 sound card selected as the output sound device in MMTTY. Original message From: Mike Dodd Date: 7/21/18 09:13 (GMT-06:00) To: elecraft@mailman.qth.net Subject: [Elecraft] K3s USB sound card problem I'm trying to get my K3s with built-in USB

Re: [Elecraft] Nice 6 m opening right now

Yeah I know...FT 8 has been going crazy all week! I've gotten several new countries confirmed on LOTW. 73, Glenn wb5tuf  Original message From: Wayne Burdick Date: 6/7/18 17:25 (GMT-06:00) To: Elecraft Reflector Cc: k...@yahoogroups.com Subject: [Elecraft] Nice 6 m opening

Re: [Elecraft] KPA1500 and FT8

I normally run 500 to 600 watts on ft8. I would go higher if my amp could do it.Life too short for QRP Glenn WB5TUF  Original message From: Carl Jón Denbow Date: 3/3/18 14:01 (GMT-06:00) To: Dennis Moore Cc: Elecraft Reflector

Re: [Elecraft] 10 m RTTY contest still going on; three CA stations calling CQ....

Nothing but channel Z down here.  WB5TUF  Original message From: Wes Stewart Date: 12/3/17 14:05 (GMT-06:00) To: elecraft@mailman.qth.net Subject: Re: [Elecraft] 10 m RTTY contest still going on;   three CA stations calling CQ If ND2T is one of you

Re: [Elecraft] 10 m RTTY contest still going on; three CA stations calling CQ....

It's pretty quiet down here in Texas...I'm calling on 28081 but only working locals. Glenn WB5TUF  Original message From: Wayne Burdick Date: 12/3/17 13:23 (GMT-06:00) To: Elecraft Reflector Subject: [Elecraft] 10 m RTTY contest

Re: [Elecraft] [P3] P3TXMon Wattage/SWR

Is it the same sensor that is used with the W2 power meter? If so, can one sensor drive both devices? Glenn WB5TUF Original message From: MaverickNH Date: 8/27/17 10:55 (GMT-06:00) To: elecraft@mailman.qth.net Subject: Re: [Elecraft] [P3] P3TXMon

Re: [Elecraft] K3: Odd ALC behavior

l Message- From: Dave Cole [mailto:d...@nk7z.net] Sent: Friday, August 04, 2017 7:54 AM To: Glenn Anderson <wb5...@comcast.net>; elecraft@mailman.qth.net Subject: Re: [Elecraft] K3: Odd ALC behavior Hi Glenn, Respectfully, the issue, as already stated a few times, in several messages, is

Re: [Elecraft] K3: Odd ALC behavior

You guys are over-thinking this "issue". Just set whatever combination of level controls it takes to get four solid bars and a flashing fifth on the ALC and get on with it.that works for me. See Y'all on FT8! Glenn WB5TUF -Original Message- From: elecraft-boun...@mailman.qth.net

[Elecraft] XV144 and RemoteRig For Sale

I have an XV144 with oven for sale. I built and tested it but decided to go for the internal transverter instead. $400.00 I also have the Remoterig RRIGSET with the RRMTCBL and RRK3CBL for sale. It is new in box never used. $450.00 Please contact me directly at wb5...@comcast.net

Re: [Elecraft] K3: Configuring N1MM to send CW

Had this same problem. I am not using a USB- just a regular COM port. I finally had to switch to the Kenwood TS 940 driver in n1mm. The K3 driver would go into transmit as soon as I would try to select the DTR function. Glenn -Original Message- From: elecraft-boun...@mailman.qth.net