Don (and Jim for info),
There could have been another reason for not showing any text in the
text-part if the message.
Jim might use a device like a "smart"phone that sends HTML-only mail.
This mailman server is set to suppress and delete any HTML markup and
attachments in received mails bef
Sorry Barry, it's empty again.
73, Peter
Op 2022-12-30 om 14:05 schreef Barry H:
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.n
Sorry Barry,
This email reflector can ony process plain text.
Mail in HTML Only end up empty here.
HTML and plain text works but no markup will be shown, just the plain
text part.
And finally any attachment is removed on arrival on the reflector.
So please write your question again as "plain tex
a new one
73,
Jorge
CX6VM/CW5W
El sáb, 3 dic 2022 a las 12:00, Peter Eijlander (PA0PJE) ()
escribió:
Hi Jorge,
Those knobs drive digital encoders. Digital encoders usually have no
hard stops.
73,
eter
Op 2022-12-03 om 02:03 schreef Jorge Diez - CX6VM:
Hello
in one of my K3 radios, AF, SUB
Hi Jorge,
Those knobs drive digital encoders. Digital encoders usually have no
hard stops.
73,
eter
Op 2022-12-03 om 02:03 schreef Jorge Diez - CX6VM:
Hello
in one of my K3 radios, AF, SUB, RF/SQL and SUB knobs turn all aroun, no
limits on right and left side
Couldn`t figure out if I need a
Dear Reed,
Send mail to this reflector as "Text only" or both text and HTML for all
HTML markup text is skipped by this qth.net mailing list.
Your mails are received as completely blank by all of us as shown below
my message.
Best 73, Peter - PA0PJE
Op 29-04-2022 om 01:12 schreef Reed Fite
Hi Bob,
Yuck!
Indeed that's what I would say also.
I for one can't stand anti-phased headphones. I once discussed that over
using stereo-headphones being fed at tip and ring and left the common
open. The comment was: No one hears that. Well I do! Splitting mono into
high and low pitched sou
That is exactly what I did, Rich and Paul...
The "connector" I used was a 2 pin connector that is/was in use in
computers to connect activity LED's and reset buttons to the main board.
They fit perfectly and can be salvaged from nearly any old PC. Use the
two right hand upper and lower pins and
Yes,Ludwig, it works OK, now!
I use Thunderbird as well and have set it to plain text from the start
using it. I am against any markup. It has been asked many times to
change that on the qth.net mailman and many times was responded with
"no" by the maintainers. Users that send both should know
Hi Ludwig,
You should write mails in plain text on this reflector.
HTML-only mails come through completely empty.
Attachments are also not allowed and will be stripped as well!
73,
Peter - PA0PJE
Op 09-09-2021 om 08:37 schreef Ludwig Hechler:
_
Yes Jerry, isopropyl alcohol does this!
I once cleaned a working print of a GPS receiver with isopropyl alcohol
and it stopped working. Letting it be and trying it again next day
turned out it worked perfectly again.
From then on I leave a PCB to rest after cleaning to have the IPA dry
out c
>>"limited to Windows"
Not so: NanoVNA-saver is software written in Python and is platform
independent. I use it on Linux Mint 20.1
https://github.com/NanoVNA-Saver/nanovna-saver
73,
Peter - PA0PJE
Op 25-06-2021 om 14:17 schreef w2xj:
The problem with that is it requires a computer and is ap
No it does not change HTML into plain text. The average mail client,
like Thunderbird can be set to send both HTML and plain text.
Some clients, more specifically those that use webmail CAN send in HTML
only. 'Smart' phones and tablets have this deficiency too. That leaves
a blank message on
Eric,
I have a NooElec R820T that does work from 25.85 MHz to 1766 MHz
Anything lower that that needs an upconverter afaik.
I can tell GQRX to go lower but it then detects nothing anymore...
GQRX is a Linux SDR program where a funcion that says "No limits" allows
to tune higher and lower than t
Dave,
https://launchpad.net/gtkhtml
But just versions for Trusty and Precise. No updates after 2013
I have the same error on the help but never needed it. Also in the GUI
btw in KX3UtilityLINUX_1_19_9_6 which runs fine in 64bit Linux.
I found several "libwebkits" in Synaptic
Installed are Lib
On 2020-09-07 at 14:35 Robert Rennard via Elecraft wrote:
I agree with Dave that we should start putting the Elecraft product model as
the first token in the mail header
This has, and still is a prerequisite nearly from the start of this list...
This is what Eric said about using this lis
I support having a separate K4 group.
I don't. I filter each Elecraft gear item in separate subfolders under a
main folder called Elecraft.
The real problem with this is the shear lack of users of this list to
mention the type of Elecraft gear they want to talk about.
Many users of the K3
Joe, you can download owner's manual/errata/accessory/tips etc here:
https://elecraft.com/pages/kx3-high-perofrmance-portable-transceiver-manuals
Page 8 of the manual describes all the display items.
72/73,
Peter
On 2020-08-19 at 20:06 Wayne Burdick wrote:
The 'T' indicates that text decode i
On 10-08-2020 at 22:35 jcj...@lagoon.nc wrote:
and they have a right to be strict.
Sorry Pierre, "they" don't... Not for radio amateurs.
Professional use like land, sea and air maybe yes.
CB certainly.
Amateurs have a license to live up to. Government may restrict
commercial amateur gear
The thing is that what you sent was not a URL.
One should not omit the protocol...
I copied the URL from my browser and pasted it here. It adds "https://";
https://catalog.data.gov/dataset/ionospheric-digital-database
is the true URL including the protocol and should be shown as such in
any dec
Groups.io works exactly like a reflector like mailman to me.
Like said time and again: Use a proper client like the free Thunderbird
mailprogram. It is there for all three major operating systems.
Do not use a web interface and stick to plain text for reduced message
size and DO NOT USE A SM
Look at DL2SBA's pages:
He did a comparison between 2 2-tone audio generators, one a kit from
Box73/Funkamateur and the other a Siglent function generator.
http://dl2sba.com/index.php/funk/shack/354-2-tone-generator-fa-2-nf
He used this application:
https://www.audiotester.de/mainE.htm
73,
P
73,
Peter (PA0PJE)
Hi Joe,
Did you add yourself in the group "dialout"?
Control Center > Users and Groups > 'your user name' > Manage groups >
Scroll to dialout, select it and click 'properties' then tick the box in
front of your username. Click ok, enter your admin password, log off and
bac
Hello Robin,
10,5 Volts is very low for a 12 V.lead-acid battery. Try to load it with
a lamp or resistor and measure the voltage at the battery again under
load condition. I doubt that all cells in the battery are good. The gel
in these batteries can dry out, which is killing them.
There is also
Radio amateurs have agreed to use one time only: It was called GMT and
now UTC and uses a 24 hour format... Let's stick to that folks, wherever
you live!
73,
Peter, PA0PJE
Op 27-06-19 om 22:36 schreef Bob McGraw K4TAX:
Indian Chief said; "White man stupid. Thinks he can cut 12" off of
o
I glued a 6.3 mm jack to the base of my Hex-Key paddle and a common
cathode double Schottky diode, that can be found in nearly any old PC
power supply, to create a straight-key input for the K2 (doesn't work
for other rigs...) and while gluing I made a
small DPDT switch to reverse the paddles fo
Aaron,
What you fail to tell is: What hardware does your Linux Mint 18.3 run on?
What I don't know and cannot test is what USB device code is produced by
the SignaLink. Normally a sound card is recognised by the linux kernel
but in some cases it isn't
Try to open a terminal screen (Ctrl-Alt+T
Well, maybe you are right. I looked at some mail I dumped that were
still in the trash.
These headers show a significant delay:
Received: from harry.qsl.net (localhost [127.0.0.1])
by mailman.qth.net (Postfix) with ESMTP id 57D63149B723
for ; Tue, 6 Feb 2018 19:04:11 -0500 (EST
I haven't seen any repeating mails here.
I use Mozilla Thunderbird and POP3. I store mail locally and have it
deleted on the mail server of my ISP so I don't sync with a remote
server with IMAP as many others do. I prefer real mail over digests and
immediately dump what I don't need.
But then a
John,
I saw that one on FunkAmateur/Box73, they sell the kit.
What appeals me is the price (155 euro), the simplicity the way it can
be built, the features, apart form being a nice graphical analyzer it's
much more like a signal generator from 100 kHz to 100 MHz. It's readable
in direct sunli
You are right, Grant.
Only this mail landed in my KX2 folder that normally when read, is
emptied for I have no KX2... You typed inadvertently XK3 in the subject
line. I have created filters that scan for types of Elecraft products
and sorts them in the proper folders.
This mail from Wayne, h
I glued a 6.3 mm jack to the base of my Ham-Key paddle and a common
cathode double Schottky diode, that can be found in nearly any old PC
power supply, to create a straight-key input and while glueing I made a
small DPDT switch to reverse the paddles for left hand operation...
I know that can b
With the K2 powerknob fully CCW it still produces some 100 mW output as
it shows on the display... I made several QSO's with that setting.
The TEST option Don W3FPR suggested is imho the best solution.
72,
Peter
Op 2017-09-25 om 20:52 schreef rich hurd WC3T:
Can you turn power to 0 watts th
Hi Eben,
Welcome to "Radio-land"
If that is normal is not for me to decide but...
I actually measured the power level of my KX3 in CW with 0.0 watt as set
level.
It varies from band to band. On 50 MHz I found -18 dBm and on the HF
bands between -20 and -30 dBm.
On 14 MHz I found -23 dBm a
Not only FM, Ron. In my car it's for both FM, MW and LW
The lines are formed in a strange way, not just horizontal parallel
wires but here and there are openings. It works well on all three bands,
that is until the last MW and LW transmitters are turned off here in
Europe and FM will be left al
Nice feature, count me in too, Wayne!
Tnx es 72,
Peter
Op 2017-05-18 om 16:43 schreef rich hurd WC3T:
Hi Wayne,
You may add me to the "KX3 interest" pileup (or pile-on depending on your
perspective. Hi hi.)
__
Elecraft mailing list
Count me out too...
I have a perfectly working delete key and I know very well how to select
a group of mails that are of no interest to me and how to create message
filters...:-)
Op 2017-05-01 om 15:04 schreef Jim Rhodes:
On 5/1/2017 5:05 AM, Michael Walker wrote:
How many of you would be
You are right, Matt.
No HTML, no attachments
73,
Peter - PA0PJE
Op 24-02-17 om 20:42 schreef Matt Zilmer:
The problem might be that the reflector doesn't pass HTML, just text.
I'm not sure about this, but remember reading it somewhere.
73,
matt W6NIA
__
And WSJT-X supports I/Q receivers like the Funcube Dongle Pro+, at least
in my Linux Mint 18.1 it does. At HF it tunes spot-on and decodes.
Tried 136 kHz, 474 kHz and several HF bands on a MiniWhip (WSPR)
Yes, 2200 meters on a piece of copper-clad 4 by 6 centimeters. 2E0ILY
QRB 520 km. Amazing..
Hi Dieter,
The KX3 decodes and displays text sent by the internal keyer, just not
with a straight key or external keyer. So does the PX3, in a different
colour than received text.
@Kevin: I have no Win, so it would be Lin4kSuite for me...:-)
73,
Peter
Op 2017-01-23 12:19 schreef ddillenbur.
Hi Dieter,
Now your post IS readable...:-)
The PX3 is of course the most obvious choice but using a PC I think
FLDIGI will certainly do the job. Just use the sidetone the KX3
produces. Route one audio channel on the stereo phones output to the
sound card input of the PC and use the other to d
Hello Harald,
If you keep sending mail to the reflector as "HTML Only" your message
will never be seen. This reflector strips all HTML from mails and
accepts only plain text. It strips any attachment too.
73,
Peter - PA0PJE
Op 2016-12-01 om 08:34 schreef Harald Fritzsche:
_
Hi Hajo,
As far as I know (I do not have a K3/P3) the SVGA-card is an addition to
the P3 that enables connection of a separate monitor.
To my knowledge there is no need for a running computer.
73,
Peter
Op 2016-08-23 om 14:23 schreef Hajo Dezelski:
I would not like to have an additional comp
Hi Jerry,
Try Nabble.
Is this maybe what you are looking for?
http://elecraft.365791.n2.nabble.com/Field-Day-tips-td7590292.html#a7590298
In this thread you were one of the posters but you can search Nabble.
If you just would search K9YC you will need some extra time to read all
of Jim's pos
You should set the transceiver's dial to 14095.6 USB. Then, as the audio
tone generated is 1500 Hz, the actual transmit frequency will be 14097.1
On receive same story: receiving with the dial set to 14095.6 a 1500 Hz
tone will be audible. That's it...
73,
Peter
Op 2016-04-02 21:54 schreef Aar
Hi Ted,
I just looked at the schematic, downloaded from the Ameritron site, and
wondered whether or not there are any protection diodes across the 3
relay coils in the remote box. They do not show on the drawing.
I can imagine these spikes could be much bigger than the +5 and -5 volts
you qu
Hello Wayne,
I have tested and use a Rapoo wireless ultra-slim keyboard model E9070
with a very tiny 2,4 GHz dongle. It has an on/off switch at the bottom
and works, as far as I can tell, flawless.
It does have a numeric keypad but still measures only 340 mm x 110 mm x
5 mm at the "spacebar
David,
Paul, N6HZ gave a direct link to the beta software on the reflector in
his mail with the subject: [Elecraft] PX3 firmware 1.35 BETA available,
USB keyboard on 2015-10-13 22:40.
http://www.elecraft.com/PX3/px3_beta_release_instructions.htm
On this particular page a link is shown to a d
FWIW and I don't know if that keyboard is available in the US: I have
tested a Rapoo model E9070 wireless ultra slim keyboard with a 5GHz
"dongle" that works, as far as I can see, very good. Of course there are
no S/C/N lights but the keys respond as expected. I bought mine in a
local e-store f
Jim,
You may not mind but it is a formal request by the moderator to do so.
I do filter, but not to delete messages. I use the filter option to have
the subjects split into different sub-folders, named with the
corresponding type of equipment.
Deleting what is not of my interest is still an ea
Op 2015-07-30 06:09 schreef Joe Subich, W4TV:
The individual posting this does not know what he's talking
about. His instruction to set the "microphone" level to 100%
is completely *wrong*.
Joe,
I have the impression he *DOES* know what he's talking about...
This is a bug he's reporting in t
I have yet to encounter a "thermal shutdown". The only time I had a
power fallback was in France during an extended CW QSO with my brother
at an ambient temperature of 31 degrees Celsius.
I did the temp. calibration by the way.
KX3 nr 3244. Never whispered with it, I have a dedicated TX for that
Don,
Then maybe this article by Pieter-Tjerk de Boer, PA3FWM on this subject
might interest you.
73,
Peter
http://wwwhome.ewi.utwente.nl/~ptdeboer/ham/tn/tn07.html
Who he is can be read here:
http://wwwhome.ewi.utwente.nl/~ptdeboer/
Op 2015-07-18 23:24 schreef Don Wilhelm:
Not only did I fin
Hi Phil,
Ever heard of the "pa0rdt mini-whip"?
Want to know how it performs?
Listen to the WEB-sdr at the Twente University made by PA3FWM.
It uses such a mini-whip created by PA0RDT.
I have one in my backyard, just two metres above the earth on an
aluminium pole in a plastic box that formerly
Dick,
Do you mean the K3 utility made by Elecraft?
There is a native Linux version available on their website.
http://www.elecraft.com/K3/software/K3UtilityLINUX_1_15_6_27.tgz
73,
Peter
Op 2015-07-14 22:10 schreef Dick Roth:
Tried installing the Memory Manager using Wine on my Ubuntu 14.04
mac
Hi Sean
You most probably have missed this message from Wayne:
On 2015-02-10 07:38 Wayne Burdick wrote:
Subject: [Elecraft] Fixed-Tune mode for the PX3: Very early version
ready for a few hardy field testers
Hi all,
Fixed-tune mode is now pretty much working on the PX3, though it's not
qu
I don't. I always use the internal keyer of my K2 and KX3.
Only on the KX3 I use a straight key connected to the front connection
that is normally used to connect the KXPD3 paddle, in order to be able
to use both a paddle and a straight key without switching or replugging.
If you happen to hav
Hi Tom,
The image nulling procedure is built in the PX3. I did not run it in
order not to alter these settings for the KX3 - I merely wanted to
indicate that is is possible. I have the necessary signal generator to
do so, that wasn't the reason not doing this...
73,
Peter
On 2015-01-28 19:2
I did, it works
With a Softrock-RX for 30 metres. The LO is an xtal on 40.5 MHz that
produces 10.125 MHz and that shows on the PX3 as 0Hz.
The real problem comes with the need to recalibrate te I/Q phase and
amplitude in order to have a good image rejection.
On -25 kHz I see the DDK9 telepr
Don,
On the other hand, Wikipedia says:
Hex keys are measured across-flats (AF), which is the distance between
two opposite (parallel) flat sides of the key. Standard metric sizes are
defined in ISO 2936:2001 "Assembly tools for screws and nuts—Hexagon
socket screw keys", also known as DIN 911
Hi Nakamura
I think you're right about this but also I think that the lo/hi-cut
settings affect the audio and not the "IF" bandwidth.
I know that in the Perseus software you can influence both AM sidebands
independently and in fact listen to only one sideband plus carrier in
both AM and AM-s
Try this one, Jorge,
http://www.n3me.net/pdf%20files/MMTTY%20v1.68A%20and%20Elecraft%20K3%20Setup%20with%20Lenovo.pdf
Otherwise you could just use
http://www.n3me.net/pdf%20files/
and pick the file you want to use.
Dell was no longer there in the file name... that why it didn't work.
73,
Peter
Free. It will send the name if the caller is in my phone book,
otherwise it sends the number.
Yes, but on my Samsung GT-I9100 'phone it's very distorted, except the
first character, I cannot control the volume and set this as default
ringtone...
And it's not free it cost me 69 eurocents t
Hi Ken,
well...
In the past there were both 2 caesium and 2 rubidium clocks on board,
according to this paper:
http://www.insidegnss.com/auto/Sept06GNSS_Solutions_secure.pdf
GPS satellites used to carry two caesium and two rubidium atomic
standards on board.
Subsequently, GPS switched to all r
Hi Jim,I use a light-weight Trust headphone-with-electret mic. that cost
me 14 euros. It has an item number 15480. To me it sounds good both on
transmit and receive and has the standard 3.5mm plugs and an in-line
volume control.
73,Peter - PA0PJE
Op 28-11-14 om 23:28 schreef Jim Lowman:
What
I think it's more the strange thing to be able to set it at 0.00.
This happens on LSB too but to me there is no audible difference at all
between 0.00 and 0.05 and one cannot set 3.00 because all settings end
on 5 in SSB. Probably next FW update will be the inability to set the
low PB slope to
Backight on? Press Menu and turn the tuning knob a very tiny little and
it's off... then turn the menu-knob a tiny little to the left and you
can set the charge time.
Is that really worth the effort of programming PF-keys for?
For me it isn't. I have more useful functions for them.
73,
Peter
Dag Wouter Jan,
Mooi dat je het hebt gevonden!
Ik heb die KXFL3-mod wel uitgevoerd dus ik kon je probleem niet
reproduceren...
Ok wat de PA-beker betreft, ik heb je dus helaas gemist. Ik gebruikte
wel de techniek die jij ook hebt geprobeerd maar met QRP kun je beter
zoeken dan roepen, ik he
Well Eric, Kelvin is an absolute number, so there is no "less than zero"
whereas Celsius is a relative number. That's why.
Op 19-11-14 om 08:16 schreef norrislawfirm2:
To pick nits, it isn't "degrees Kelvin" it's just Kelvin or Kelvins. I don't
know why.
73
Eric WD6DBM
_
Phil W7OX
On 11/18/14 12:34 AM, Peter Eijlander (PA0PJE) wrote:
It's even kHz, with a lower case k, gentlemen...
mHz (yes millihertz!), Hz, kHz, MHz, GHz, THz
Op 17-11-14 om 19:29 schreef Phil Wheeler:
I think you meant KHz, not
It's even kHz, with a lower case k, gentlemen...
mHz (yes millihertz!), Hz, kHz, MHz, GHz, THz
Op 17-11-14 om 19:29 schreef Phil Wheeler:
I think you meant KHz, not MHz, David :-)
__
Elecraft mailing list
Home: http://mailman.qth.net/
I have got it working in Ubuntu 12.04 64bit.
Indeed you need to add yourself to the dialout group and have the 32bit
libraries.
It is an item that should be the system settings window under user
accounts but as I wrote before in the reflector:
I had the same issue in Ubuntu Linux. The reason
Jim,
Did you read the manual's page 6, first item under figure 1, ie did you
turn on the RX I/Q function in the KX3?
73,
Peter - PA0PJE
Op 2014-10-18 20:09 schreef Jim GM:
Carl TNX for responding so fast.
No I do not. Just turned it on and now I can see signals.
What else do I need to t
Sorry It's not as easy to find as I just said but never the less the
reason for the empty mails is what I stated before:
All HTML is stripped by the listserver for this reflector so use plain
text...
Op 2014-09-28 09:05 schreef Peter Eijlander (PA0PJE):
Please read the FAQ on:
Hello Paul
What you probably don't know, but should be known to the users of this
reflector:
Mail MUST be in both plain text and HTML at least but preferably plain
text only and even preferably in plain text only and leave out anny
markup like text colors, bold, italic etc. for it will not s
I did something similar. I soldered a
two-Schottky-diodes-in-one-package-with-common-cathode device, salvaged
from a switching PSU, on a 6.3 mm jack, glued it to the base plate of my
sqeeze-paddle and I just have to plug in my straight key and can
instantly use both.
Op 2014-09-19 09:41 schre
Hello Gerry,
I did not realize you are visually impaired.
Charles N2SO sent a message as well in a shorter form effectively
telling the same thing. Of course it depends also on the firmware
version on your KX3 whether this setting is available or not.
Is there anyone else with a good idea apa
Owner's manual version C4 page 37:
CW WGHT
Adjusts element/space timing ratio (weight) for the internal keyer.
Additional functions of this menu entry, via numeric keypad:
Tap 1 to select S S B - C W (default) or S S B + C W (allows CW in SSB
modes).
When CW-in-SSB is in effect, tapping the KEY
hreef Nr4c:
Read the manual, as I did. Unhook everything from KX3 and connect computer to
KX3. Restart utility and it will continue load. Took a few tries but eventually
worked.
Sent from my iPhone
...nr4c. bill
On Sep 11, 2014, at 11:57 AM, "Peter Eijlander (PA0PJE)"
wrote:
I had
Ooops, that should be "dialout"...
Op 2014-09-11 17:57 schreef Peter Eijlander (PA0PJE):
If you add yourself to the group "dialup" like this:
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo
I had the same issue in Ubuntu Linux. The reason was that by default
only root has access to /dev/ttyUSB0.
If you add yourself to the group "dialup" like this:
In a terminal do at the ~$ prompt:
sudo usermod -a -G dialout
where should be your name as shown on the prompt before the @...
log
Hi Glenn,
I did something else for that purpose; I created a small pigs tail with
a two pin female connector and a 6.3 mm female stereo connector at the
other end for my straight key and plug the paddle in the "key" connector
at the left side. In the setup I set the side connector to normal ia
Mark, this one did work out but the main problem is that less and less
people seem to understand that this reflector does not allow HTML, so
breaks up any added text mark-up. Use plain unformatted text at all
times when answering the reflector and do not even try to send an
attachment. All that
Hi Gary,
The signal you are referring to is a STANAG 4285 military transmission
from Turkey. The curly things you see in the spectrum is in fact
selective fading in the sent spectrum, which is roughly 10 kHz wide.
10.1102 MHz-USB-Izmir, Turkey Turkish Navy - STANAG 4285
from:
http://qrg.gl
The server deletes ALL code and just leaves the the plain text message.
The bottom line is:
Just paste the link and do no use HTML to bury it in some nice clickable
button...
see for yourself:
http://topbanddinner.jimdo.com/
Cheers,
Peter
Op 2014-01-14 2:46 schreef wb6r...@mac.com:
The cli
The problem is the terminology, John.
In this case "FSK" and "PSK" should have been read as "ASCII" and
"Morse code". The translation from "ASCII" to "Varicode" to "PSK" and
vice versa as well as "ASCII etc" first to "5 bit Baudot" and then to
"FSK" is done by software in the radio itself, as o
Tried it Bob: Spike still there. No difference with the previous
version. I already had it at -110 dBm so not really an issue but using
the I/Q cable supplied remains disastrous, you need the galvanic separation.
I could create the overload warning in 2.6 but the software kept running.
NaP3 use
st confess that this was indeed very easy to set up. I will play
some more:-)
If you want screenshots of how this looks, just let me know.
73,
Peter
Op 2013-12-24 15:23 schreef Peter Eijlander (PA0PJE):
I tried NaP3 but I'm afarid I am too much a HDSDR type so I get stuck on
using Po
Ariel NY4G
Sent from my iPad
On Dec 24, 2013, at 8:23 AM, "Peter Eijlander (PA0PJE)"
wrote:
Hi Al and Ariel,
I suppose you both know the existence and have thoroughly read this page?
http://www.telepostinc.com/NaP3.html
73,
Peter
Op 2013-12-23 18:38 schreef Ariel Jacala:
I a
Options menu (F7) > Swap I and Q channels fixes that fast...
But be aware that all cables should be wired so, that I and Q are
connected the same way to the L and R line inputs of the sound card.
73,
Peter
Op 2013-12-09 1:00 schreef Chris Johnson:
I followed the guide on HDSDR's website for t
Hi John,
I second that!
Don't we all know how it feels to miss that one line in a manual and
then being directed the right way?
Cheers,
Peter PA0PJE
John Buck schreef:
Again Don, I thank you for your ever courteous and accurate responses to
those of us who sometimes go down the wrong path and
Dave,
I have a tuner in my K2 (built in 2005 KAT-2) and one in my KX3. they
never failed and in most if not all cases I was able to tune various
pieces of wire tossed in trees to dipoles, resonant or not.
These tuners are very unlike the "YaeComWood-tuners" you mentioned and
do tune vast ranges
Me too:-)
73, Peter
Alan Hawrylyshen schreef:
I'll second this - I really love the SideKX product - I feel like the radio is
backpack and road-worthy in the extreme now.
Alan
K2ACK
__
Elecraft mailing list
Home: http://mailman.qth.n
Ron D'Eau Claire wrote:
in my K2 (built in 2000) and
it has had a lot use.
Mine went broke after some 6 years of use so I ordered a new one.
Still need to replace it...:-)
I have a dummy plug at hand to turn off the internal speaker of my K2,
the headphone jack connection is still ok, just t
It is, David, only you are sending the mails twice...
73,
Peter
David Anderson schreef:
Hope my email is in plain enough text for the reflector now, have
moved over to another mail client on the iPad.
73
David Anderson GM4JJJ
__
Hello David and welcome to the list.
As you can see your text is filled with HTML content.
Be it known that HTML is stripped from messages sent to the list.
Sometimes even completely blank messages will arrive having only a
subject but no body.
In that case a mail client is used that creates
John,
What you ask is not possible on the reflector. It is either all or
nothing. Participants are asked to always put the type of Elecraft
equipment, the mail is about, in the subject line but unfortunately
frequently this is ignored.
I use an off-line reader (Thunderbird in my case) and ha
And isn't the activation of the VFO isolation amplifier (RX ISO>On) a
solution?
At least that prevents the VFO signal to exit via the antenna and enter
the mains wiring.
I have yet to experience this breakthrough.
73,
Peter
Don Wilhelm schreef:
Yes, that is true. You have to choose betwee
Hi Ray and John,
KSB2 manual page 22:
Note: The BFO settings for LSB and USB are swapped on 15, 12 and 10
meters due to the K2's frequency
mixing scheme. If you use 17 m or below for making BFO changes, the
following rules apply:
LSB: moving the LSB BFO lower in frequency will raise the voice p
Don,
In my view it is...
72,
Peter
Don Wilhelm schreef:
or is that just another rumor on the internet?
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto
1 - 100 of 131 matches
Mail list logo