On 4/28/2018 4:55 PM, Don Wilhelm wrote:
> Unless the wiring route is short, take Jim Beown's (K9YC) advice about
> conductor sizes. Large conductors are not required for the current
> draw, but oversize wire will help reduce the voltage drop when current
> is drawn.
That's why, for one of the
Ted,
I wonder if the load center panel is mounted on an exterior wall? If
so running a penetration from the panel to outside might be
better. Then you could route it in conduit or exterior cable routed
along exterior to a good spot to bring it back inside at the lower
level. That still
On 4/28/2018 11:08 AM, Dauer, Edward wrote:
> I did think to have a conduit put through the wall to allow antenna
> feedline coax to go through; but the electrician who was there said
> there is now no way to get a 220 line through the walls without major
> destruction.
My wife is a now-retired
At the risk of spinning this off topic, I am reminded of the lesson I
learned years ago when I drilled a through hole through the foundation for
our low voltage walkway wiring.
I wondered at the efficacy of my brand new shiny Dewalt hammer drill
because it was taking me freaking hours to go a few
Ted,
The routing of the 240 volt wiring is a discussion between you and the
electrician - but there is always "a way" - even if that means drilling
through concrete (not nice, but possible).
Unless the wiring route is short, take Jim Beown's (K9YC) advice about
conductor sizes. Large
Ed,
I live in a 4 level split. Not a good situation for my knees and running power
lines.
I assume the breaker box is on an outside wall. Here is what I did .
I went outside.
My shack in on level three, half buried in soil. Ground level comes up to just
below the windows.
I had an electrician
On Sat, Apr 28, 2018 at 11:08 AM, Dauer, Edward wrote:
> Placing both PS and amp where the 220 VAC outlet is accessible is
> possible; but then I wouldn't be able to see the amp while operating, which
> I would like to do. Wouldn't feel comfortable with a 1500 watt amp
Use metallic or nonmetallic cable raceway to run the wire on the wall.
Its available in many different styles and colors
73
Frank
W3LPL
- Original Message -
From: "Edward Dauer"
To: "Dave AD6A" , elecraft@mailman.qth.net
Sent: Saturday,
On 4/28/2018 11:08 AM, Dauer, Edward wrote:
I might bring it overhead (between the finished ceiling of the lower level and the floor
of the next level up) but then to get it down to a usable level in the "shack"
would require a conduit running down the inside wall surface. That may be what I
Placing both PS and amp where the 220 VAC outlet is accessible is possible; but
then I wouldn't be able to see the amp while operating, which I would like to
do. Wouldn't feel comfortable with a 1500 watt amp running way out of sight.
It would also then be in the kitchen on a floor above.
I concur... Should have replied to the original post. Sorry.
OK... you NEED 240 in the shack, so if you are going to do it... and
you should, do it right.
Put a sub-panel in the basement and take at least a 60, preferably an
80+ Amp line from the main box to the sub-panel. Then hack out
Ted,
I would opt for bring the 220 line into the shack.
Ask your electrician about using a receptacle mounted flush on the
floor. You have likely seen them used in commercial buildings -
conference rooms and other places - the cover plate is usually brass
with a "door" to expose the
Why not just use the amp as-is near the 220V outlet and run longer RF coax
cables to the amp from your operating position?
Dave
AD6A
Sent from my iPhone X
On Apr 28, 2018, at 6:54 AM, Dauer, Edward wrote:
The KPA1500 Manual states that “the power supply can be operated
I would revisit running a 240 outlet into the shack. You would need very
large conductors to have the power supply that far away and laying these
wires on the floor would certainly not be aesthetically pleasing. It is
sometimes a bit of work and may require some drywall repair however I cannot
The KPA1500 Manual states that “the power supply can be operated remotely” and
that the supplied cables are 66 inches long. It does not say how far apart,
beyond the 66 inches, the PS and the amp can be without affecting performance
or creating other issues.
Does anyone know? There are
15 matches
Mail list logo