I do not have my K3 yet. I have been reading about it.
I would like to use it with an Ameritron AL82 in semi QSK (vox on).
I do not see an amp connection mentioned in the manual
What is the hook up for a non QSK amp to the K3?
Tks very much
Gerry
Gerry,
As with any amplifier ---
Connect the K3 output coax to the AL82 input coax, and connect the K3
KEYOUT to the AL82 PTT IN (or whatever they call it).
Forget the ALC cable - instead, adjust the K3 power output to drive the
AL82 to its full output (or whatever you want below that level),
Change training below to trailing
73,
Don W3FPR
On 12/24/2012 7:08 PM, Don Wilhelm wrote:
In other words, semi QSK controls the training edge of the KEYOUT
signal, but does not change the leading edge. TX DLY will control the
leading edge up to the limit of its range.
On Fri, 2008-03-21 at 18:33 -0700, hank k8dd wrote:
The problem with Elecraft rigs switching Ameritron amps
has existed with the K2/100 and, so it appears, now with
the K3/100.
I think the problem is not elecraft rigs but amplifiers that have
unreasonably slow switching times.
10msec or
if
they could easily make the modification in the firmware. If they decide to
respond to this issue and say they won't or can't do it then I'll be glad to
look for a hardware modification to my amp.
73,
Roger W1EM
-Original Message-
From: Brendan Minish
Subject: Re: [Elecraft] K3
I've got a K3 on order, and I'm not worried at all about
timing issues switching my amplifier. I use a microHam
CW keyer to key all my rigs. The cw keyer uses the K1EL
chip that puts out a PTT signal (for keying an amplifier) with programmable
lead-in and tail times with respect to
the CW
Hallo Roger,
delay times. So far there's been no response from Elecraft concerning this
subject after a few days of discussion on this list. We don't even know if
they could easily make the modification in the firmware.
Elecraft has said in the past, several times, that they will be
I think the problem is not elecraft rigs but amplifiers that have
unreasonably slow switching times.
10msec or longer is unreasonably slow and I think it's 'unreasonable' to
blame the manufacturer of the radio because the amp manufacturer saved a
few bucks and used a cheap, slow relay instead
On Sat, Mar 22, 2008 at 6:10 AM, Brendan Minish [EMAIL PROTECTED] wrote:
On Fri, 2008-03-21 at 18:33 -0700, hank k8dd wrote:
The problem with Elecraft rigs switching Ameritron amps
has existed with the K2/100 and, so it appears, now with
the K3/100.
I think the problem is not
Bob speaks the truth here. The K6XX fast relay circuit
is the answer.
The problem with Elecraft rigs switching Ameritron amps
has existed with the K2/100 and, so it appears, now with
the K3/100.
I have had the K6XX fast relay circuit in my AL-1200
working with the K2/100's. No KPA-100
My K3 #339 went QRV yesterday afternoon after successfully
downloading firmware via the upgraded Mac utility. The previous
version of the utility, which I had downloaded weeks ago in
anticipation, did not allow for successful DSP firmware download.
With the new utility it was a breeze.
I
Hi Tod,
One question remains and it is probably ridiculously simple but I can
not see it. How do I get the K3 to trigger the relay in my Ameritron AL
1200?. I see no connection for a cable to the amp nor nothing in the
config menu.
I don't know the Ameritron AL but KEY OUT should be what you
The KEY OUT RCA jack on the back of the K3 will key the amp.
Phil - AD5X
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
-Original Message-
From: Todd Ruby
I received 59+20 and excellent audio from central europe. ... How do I
get the K3 to trigger the relay in my Ameritron AL 1200?.
-
If you're 20 over in Europe, you don't need an amp!! :-)
- Keith N1AS -
- K2 5411.ssb.100 -
-
Todd
Beware the manual for the AL1200 doesn't appear to mention the change
over timing of it's relay, the K3 outputs RF approx 10 milli seconds
after the linear keying line goes low - measured on mine with a half
decent scope. There is currently no adjustable delay for that timing in
the K3
Todd -
KEY OUT on the back of the K3 is for connecting to an external amp.
-
73,
Greg - AB7R
Whidbey Island WA
NA-065
K3#0009 and 0319
On Thu Mar 20 5:27 , Todd Ruby sent:
My K3 #339 went QRV yesterday afternoon after successfully
downloading firmware via the
be
less expensive.
Roger, W1EM
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Dave G4AON
Sent: Thursday, March 20, 2008 10:45 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 and linear amp
Todd
Beware the manual for the AL1200 doesn't appear
I have the same issue with a slow switching linear and am thinking about
putting a slow relay in the keying circuit which I need anyway to invert the
keying signal.
-
Chuck, AE4CW
--
View this message in context:
http://www.nabble.com/K3-and-linear-amp-tp16180386p16181739.html
Sent
Beware the manual for the AL1200 doesn't appear to mention the change
over timing of it's relay, the K3 outputs RF approx 10 milli seconds
after the linear keying line goes low - measured on mine with a half
decent scope. There is currently no adjustable delay for that timing in
the K3 ...
I
: [Elecraft] K3 and linear amp
Todd
Beware the manual for the AL1200 doesn't appear to mention the change over
timing of it's relay, the K3 outputs RF approx 10 milli seconds after the
linear keying line goes low - measured on mine with a half decent scope.
There is currently no adjustable
Hold the phone.
I am using my K3 with an AL80A...basic amp with the same relay as many of the
other Amertrons use. I have seen no issues at all. Also, you might look at
this little gimmick that might help you out here This is the URL
http://www.k6xx.com/radio/fastrely.html
Also,
Roger Marrotte wrote:
I guess as of now I'm out of luck if I want to use my amp with a K3. I
just checked the manual for my AL-811H and The open frame relay in the
AL-811H takes approximately 15ms to switch states. My K3 is on order.
I hope there's a K3 firmware change made before I get my
Message -
From: Roger Marrotte [EMAIL PROTECTED]
To: 'Dave G4AON' [EMAIL PROTECTED];
Elecraft@mailman.qth.net
Sent: Thursday, March 20, 2008 7:12 AM
Subject: RE: [Elecraft] K3 and linear amp
I guess as of now I'm out of luck if I want to use my amp with a K3.
I just
checked the manual for my
Or rebuild the amp with faster relays like the Jennings RJ1A.
Jim SM2EKM
--
AE4CW wrote:
I have the same issue with a slow switching linear and am thinking about
putting a slow relay in the keying circuit which I need anyway to invert the
keying signal.
-
Chuck,
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Dave G4AON
Sent: Thursday, March 20, 2008 10:45 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] K3 and linear amp
Todd
Beware the manual for the AL1200 doesn't appear to mention the change
25 matches
Mail list logo