"My KAT500 will no longer tune in AUTO mode on 20M and does not change to
prior stored settings in MAN mode. All other bands work as expected in
both modes. Any suggestions on where I should look first?"
Use the utility to check that KAT500 has tuned to your 20 m frequency. If it
has, then com
Using the utility, erase the settings for 20M and reteach it? Once
trained, leave it in MAN mode for daily use.
73,
Rick nk7i
On 4/9/2024 8:30 AM, Mike Murray wrote:
My KAT500 will no longer tune in AUTO mode on 20M and does not change to
prior stored settings in MAN mode. All other bands wo
My KAT500 will no longer tune in AUTO mode on 20M and does not change to
prior stored settings in MAN mode. All other bands work as expected in
both modes. Any suggestions on where I should look first?
Mike - W0AG
__
Elecraft mailing li
Thanks to Dick K6KR for helping me with this problem yesterday. Updating the
KAT500 utility program, in combination with a KAT500 firmware reload, fixed
the issue.
--Ed--
Message: 7
Date: Sun, 6 Mar 2016 08:08:11 -0500
From: "Ed G"
To:
Subject: [Elecraft] KAT500 Utility Question
Message-ID:
From our KAT500 Utility author Dick Dievendorff:
===
"If you have [KAT500] firmware version 1.63 and "sleep when Idle" on, that
combination has a switch problem that has been corrected in Beta firmware
version 1.67, available on our web site.
...
We're probably going to put 1.67 into production e
If you are sure it's related to a firmware update,
can you revert to earlier firmware to confirm?
Phil W7OX
On 4/14/14, 12:47 AM, Gary Gregory wrote:
Same FW here...I can confirm the "dicky" switch action also and this has
been going on since the upgrade but not before.
Easily repeatable here
-Original Message-
>>> From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
>>> boun...@mailman.qth.net] On Behalf Of Phil Hystad Sent: Sunday,
>>> April 13, 2014 3:02 PM To: Elecraft
>>> Subject: [Elecraft] KAT500 Problem --- switching antenn
Same FW here...I can confirm the "dicky" switch action also and this has
been going on since the upgrade but not before.
Easily repeatable here too.
Gary
On 14 April 2014 11:49, Fred Jensen wrote:
> 1.63, 3 antennas, all OK here
>
> 73,
>
> Fred K6DGW
> - Northern California Contest Club
> - C
1.63, 3 antennas, all OK here
73,
Fred K6DGW
- Northern California Contest Club
- CU in the 2014 Cal QSO Party 4-5 Oct 2014
- www.cqp.org
On 4/13/2014 4:15 PM, Cady, Fred wrote:
Not seeing it here, Phil.
KAT firmware 1.63
73,
Fred KE7X
___
ay, April 13, 2014 3:02 PM
>> To: Elecraft
>> Subject: [Elecraft] KAT500 Problem --- switching antennas
>>
>> Ever since the most recent KAT500/KPA500 firmware updates, switching
>> between antenna 1 and 2 shows funny behavior.
>>
>> For example, on the 20 mete
Not seeing it here, Phil.
KAT firmware 1.63
73,
Fred KE7X
> -Original Message-
> From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
> boun...@mailman.qth.net] On Behalf Of Phil Hystad
> Sent: Sunday, April 13, 2014 3:02 PM
> To: Elecraft
> Subject: [Elecra
Ever since the most recent KAT500/KPA500 firmware updates, switching between
antenna 1 and 2 shows funny behavior.
For example, on the 20 meter band I have two antennas:
Antenna #1 -- Wire 80-meter Dipole (ladder line fed)
Antenna #2 -- Hex beam
So, I am positioned on antenna #
Barry,
According to the current KAT500 manual, top of p. 11:
"IMPORTANT: If you are using the KAT500 with an Elecraft K3 transceiver
connected using DB15 cables as shown in Figure 1 or Figure 2, you must
apply power to the KAT500 before turning the K3 on. If you turn the K3
on before applying
Barry,
Just curious but after your initial disconnect of your K3 station, did you plug
the exact same DB15 cables back into the same individual components? Also, did
you have your KAT500 hooked up the PC at anytime during the dismantling and not
shut the PC down before disconnecting it? I did th
Thanks Gary
I have messed and fiddled and fiddled and messed and have now swapped the
two DB15 cables back again. For whatever reason, it has now started to work
OK again. I don't know why !!
I will keep my fingers crossed that it keeps working.
73
Barry VK2BJ
On 18 March 2013 08:42, Gary Gre
Yesterday I spent all day rearranging my shack which included disconnecting
and relocating my K3/KPA500/KAT500.
The gear is interconnected using the Elecraft DB15 cables from K3 to KAT500
and KAT500 to KPA500 all as per diagram on P6 (Fig 1) of the manual.
All was working great before I disassemb
and good luck
Geoff
G3UCK
-Original Message-
From: Hunsdon Cary III
Sent: Sunday, January 13, 2013 4:37 PM
To: elecraft@mailman.qth.net
Cc: w4...@arrl.net ; Mark n2qt ; Henry and Jo
Subject: Re: [Elecraft] KAT500 problem
Following up on my High SWR problems (no response from Elecraft
In your original post you say that you turned on the KPA100 in the
K3. You should have the KPA100 turned off when using the KAT500. The
KAT100 is not needed when using the KAT500.
Make sure that when you are tuning with the KAT500 the TUNE POWER is
set to 25W. Below 20W will not give an accurat
You're right I'm sorry I apologize. I'm on pain medication from having my
shoulder replaced 2 days ago and I'm still a bit on the loopy Side. I am
able to do text to speech on email but that's about it.
On Jan 13, 2013 9:04 AM, "Hunsdon Cary III" wrote:
> Actually Greg, 230pm on the east coast is
Cary,
230 your time was actually 530 on the west coast which is where Elecraft
is based out of chances are they did not get the email prior to closing.
73
Greg
On Jan 13, 2013 8:38 AM, "Hunsdon Cary III" wrote:
> Following up on my High SWR problems (no response from Elecraft Support on
> Fri
Following up on my High SWR problems (no response from Elecraft Support on
Friday to my email):
I disconnected the KAT500 and KPA500 and connected A4S feed-line directly to
the K3. It loaded beautifully and the internal tuner read 1.0-1. Good, not
the feed line or the K3…
Next I connected the
Kat500 problem solved.
reset the parameters in the utility program (EEINIT;)
That did it. Kat500 is working great..
thanks to all that responded.
Don...w2xb
P.S. great reflector!!!
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KAT500-problem-solved-tp7565439
22 matches
Mail list logo