to Elecraft for my faithful dx pileup buster..
Ronnie W5SUM
Sent from Mail for Windows 10
From: Lyn Norstad
Sent: Monday, April 5, 2021 8:47 AM
To: 'rikoski'; elecraft@mailman.qth.net
Subject: Re: [Elecraft] No power out of a K line.
Rick -
You don't say if the 160 meter operatio
Rikoski
Subject: [Elecraft] No power out of a K line.
I have an Elecraft K3, KAT 500 and KPA 500.
I usually use it at full power with a 260’ off-center dipole on 160, 80, 40,
and 20m.
Last week, I tried it with a 140’ doublet on 160 meters to see if the tuner
would be able to reduce th
I have an Elecraft K3, KAT 500 and KPA 500.
I usually use it at full power with a 260’ off-center dipole on 160, 80, 40,
and 20m.
Last week, I tried it with a 140’ doublet on 160 meters to see if the tuner
would be able to reduce the swr to enable operation on that band.
Since then wh
I was doing FT8 and had made a few as when I suddenly had no power out. Did the
basic trouble shooting with a dummy load. Still no power out. Called Elecraft
and they said that the low power amp was out. Did some on line research and
found that when tuning up the external ant tuner at 5 watts i
As I stated, I can hear audio through headphones from the computer's
speaker port when I key the rig in WSJT-X.
Assuming you have more than one sound card with one driving the
computer speaker and the other connected to the K3/K3S "Line In"
if you hear sound from the computer speaker WSJT-X i
Ed,
Is this a K3 that has been upgraded with the KIO3B option? Or is it a K3S?
If so did you plug anything into the LINE IN jack on the back - either
intentionally or by mistake? That will open the path for the internal
soundcard output.
Switch to SSB and try transmitting voice - if that wo
I've been using my K3 almost exclusively on WSJT-X FT8 since the mode
came into being. Things worked fine until a couple days ago when I no
longer see any power out or ALC indication regardless of band setting.
All connections remain as before, untouched. I switched to MMTTY and
AFSK-A to try RT
Ok, got it working. I have two KSNY3 boards on main and SUB receivers. The
led was on for the SUB but the LED on the main was off. I switched the
boards and it started working. Must have been a loose connection on one of
the cables???
--
View this message in context:
http://elecraft.365791.n
One correction to Ron's posting: The Sub Rx's KSYN3a (if you have the
sub-receiver installed) may have a blinking green status light until the sub is
actually turned on for the first time from the K3 front panel.
73,
Eric
/elecraft.com/
On 9/30/2015 8:03 AM, Ron D'Eau Claire wrote:
Anything
Anything that disables the synthesizer will produce those symptoms. Check
the TMP cables that connect the KREF3 to the KSYN3 and to the K3 RF board to
make sure they are all properly seated. If your K3 has the newer KSYN3A
synthesizer board (mounted on the front panel shield with the KREF3) you
sho
John G4ZTR
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of way235
Sent: 30 September 2015 04:52
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] No power out and no receive
I also tried ant 2 since it has the ATU but I hav
What is the serial number of your transceiver and do you have a callsign?
Also, what revision of the manual do you have? With that information there are
lots of people on here able to help you.
73 de David G4DMP
On 30 Sep 2015 04:29, way235 wrote:
>
> I have noise on all bands but don't hear
I also tried ant 2 since it has the ATU but I have the same problem on both
ant connectors.
No power out and no RX just noise.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/No-power-out-and-no-receive-tp7608524p7608527.html
Sent from the Elecraft mailing list archive at
Which Elecraft transceiver? Kit or factory built? Was it working
before or has it never worked properly?
73,
Don W3FPR
On 9/29/2015 11:29 PM, way235 wrote:
I have noise on all bands but don't hear any signals at all.
I have a TX light when keyed and can see the meter move when I speak into
t
just something to check -- is the right antenna selected? (I've done that.)
Peter W0LLN
On Fri, May 17, 2013 at 12:55 PM, Steve wrote:
> Almost forgot...no receive either
>
> Sent from my I-Phone
> __
> Elecraft mailing list
>
Almost forgot...no receive either
Sent from my I-Phone
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http
nu entry to
> > "PA BYP"? After that the next thing to try might be to bypass the KAT3.
> >
> > 73,
> > Gary KI4GGX
> >
> >
> > -Original Message-
> > From: Brett Howard [mailto:[EMAIL PROTECTED]
> > Sent: Saturday 28 J
Ok so we're out at field day and all of the sudden I heard a somewhat
strong signal and then all the receive has gone to low S Meter numbers
yet the radio is not deaf at all.
Whats worse is that I am getting no RF out. Pressing tune the radio
draws about 2.3A and displays -- for the SWR. When
My bad! Eric is totally correct about having the B vfo set
to a mode other than cw. The problem I solved by
cycling the power is sort of related (I guess?). Several
times this has happened:
The "TX" icon at the right side of the display starts cycling
at about a 2 per second rate.
When you select
For the past couple of years my K2/100 been was working fine, and it still
works with PSK31, but I noticed a few days ago that when I connect the mic I
get no measurable power out on SSB. I'm not sure what has caused my K2 (ser.
03082) to stop putting out any power when used with the mic (MH2).
Cathy,
Definitions first - RF IN and RF OUT are designation of the RF Bandpass
filter only - on transmmit the signal goes in as RF IN and comes out as RF
OUT - however, on receive the path through the RF Bandpass is reversed, so
'in' is 'out' and and 'out' is 'in' .
Since you have a scope, I sugg
Cathy wrote:
>I've nearly completed my K1, and the receiver has been calibrated and
>works extremely well
>
>Sadly, the transmitter has not been so kind. Any attempt to put the
>unit in transmit mode (by pushing WPM+ and WPM- together) resets the
>power out to 0.1 watts, which is confirm
I've nearly completed my K1, and the receiver has been calibrated and
works extremely well. While calibrating the receiver against my K2, I
had a 3 foot antenna consisting of daisy-chained alligator clips
attached to the antenna jack, and I was picking up not only the adjacent
K2, but also RTT
23 matches
Mail list logo
