Subject: RE: [Elecraft] Split ops?
Bob Serwy wrote:
>
> Yes there is. I use it.
>
> 'k31;swt13;swt13;k30;
>
>
OK. I mis-remembered the problem I had trying to get this to work.
I'm sending SWT13;SWT13;UPB4;UPB4;SWH13;
The two VFOs *are* being set to the same f
it on and off.
Bob Serwy - N9RS
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of G4ILO
Sent: Saturday, July 05, 2008 3:45 AM
To: elecraft@mailman.qth.net
Subject: RE: [Elecraft] Split ops?
Bob Serwy wrote:
>
> Yes there is. I use it.
>
Bob Serwy wrote:
>
> Yes there is. I use it.
>
> 'k31;swt13;swt13;k30;
>
>
OK. I mis-remembered the problem I had trying to get this to work.
I'm sending SWT13;SWT13;UPB4;UPB4;SWH13;
The two VFOs *are* being set to the same frequency and mode, and SPLIT is
being engaged, but VFO B is not
Yes there is. I use it.
'k31;swt13;swt13;k30;
Bob Serwy - N9RS
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of G4ILO
Sent: Friday, July 04, 2008 4:57 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] Split ops?
Don Wilhelm
Don Wilhelm wrote:
>
> Several folks wanted it that way (for several reasons), so there was a
> recent change.
> One tap of the A>B button changes only the frequency. Two taps will
> change the mode and other settings too.
>
> Look at the firmware release notes for further explanation.
>
Un
Tap A>B a second time right after the first tap. Then you will see A>B ALL.
73
Greg
AB7R
- Original Message -
From: "TMorton" <[EMAIL PROTECTED]>
To:
Sent: Friday, July 04, 2008 8:56 AM
Subject: [Elecraft] Split ops?
When making the selection A>B then hold
Tom,
Several folks wanted it that way (for several reasons), so there was a
recent change.
One tap of the A>B button changes only the frequency. Two taps will
change the mode and other settings too.
Look at the firmware release notes for further explanation.
73,
Don W3FPR
TMorton wrote:
Wh
A second button press is now required to transfer the mode setting.
According to the release notes for version MCU 1.87 / DSP 1.69:
"* A->B SWITCH: 1st tap copies frequency only; 2nd tap within 2
seconds copies mode
and filter settings."
Bob NW8L
On Fri, Jul 4, 2008 at 9:56 AM, TMorton <[EMAIL P
Hi Tom,
You need to tap A=>B twice to transfer all the parameters, freq, mode, etc.
73, Bud N7CW
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of TMorton
Sent: Friday, July 04, 2008 8:56 AM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Split
When making the selection A>B then holding "Split" I notice that the
mode stays where it last was...i.e., 14005 on A and 14180 on B; after
A>B the B vfo is 14005 but remains in USB. I have looked thru the menu
selections and can not find anything to have the modes match after doing
A>B...have I
10 matches
Mail list logo