You need to Hold down DATA MD and select the right data sub-mode. It is set
per-band.
DATA A is usually the correct sub-mode for FT8. This uses the USB mode.
On 30m, you were likely using the AFSK A mode, which is similar, but uses LSB
mode. AFSK A is used for RTTY, generally.
> On Jun 19,
Dear OM or YL: Today I did a successful POTA activation using my K3. I
usually use a smaller, lower wattage rig, but decided recently to use the K3
portable. I've used the K3 for POTA activation three times before this week
-- but all on SSB. Today, I used FT8. I first was on 20M and
Robin,
I certainly have not seen that behavior, but recommend you go over the
P3SVGA and P3TXMON option instructions.
Are all cables fully plugged in, and are the cables dressed inside like
what is shown in the diagrams? You may have to devise some kind of
'clip or support' to keep the
My P3 has started to exhibit some strange behavior since I installed the SVGA
and TXMon options. Every time I turn the VFO A the P3 acts like it is being
overloaded and the display shows interference. I have never noticed this
before. Has anyone seen this behavior before? I am running a K3S
Jerry,
That is "just another data mode" to the K3.
First, you may be better off using DATA A submode rather than USB
because the compression is automatically set to zero and the TX EQ is
set flat. That allows you to set your SSB compression and TX EQ as you
wish for voice modes.
Like all
Yes. Read the manual on setting levels for digital modes in the manual. Forget
anything you knew before.
Sent from my iPhone
...nr4c. bill
> On Jan 17, 2017, at 7:56 PM, Jerry wrote:
>
> Hello,
>
>
>
> I am using my K3, KAT500 and KPA500 in an MARS environment and
Hello,
I am using my K3, KAT500 and KPA500 in an MARS environment and I am having
this problem. We use the M110A data mode to transfer messages between
stations - sort of like FLdigi only the mode is not legal on amateur
frequencies.
When I use the M110A (Signalink is the interface and
My P3 shows some strange behavior when combined with a K33 (newest firmware on
K3S and P3):
1. When the subreceiver is turned on in LSB mode (listening to a qso on the low
bands) and VFO B cursor is also on, the cursor VFO B changes from LSB to
USB, if the mode of the main receiver is changed
See below…..
> On Jan 15, 2016, at 3:26 PM, Martin wrote:
>
>
> …….. if the mode of the main receiver is changed from any mode to TX DATA
> (Submode
> DATA A).
Noter, there is no Mode "TX DATA”. The “TX” is an icon with an arrow pointing
either down to it, or up to it
Hi Paul,
many thanks for Your info.
It seems to me, the P3 under certain conditions displaying an USB cursor
if the subreceiver is switched to LSB (Problem #1) is also a bug in the
firmware ?
73, Martin
Paul Saffren N6HZ schrieb:
Hi Martin,
Problem #2 is a bug in the P3 firmware. With
Hi Martin,
Problem #2 is a bug in the P3 firmware. With the new K3S there are
additional steps in both the attenuator and the preamp that the P3 is not
taking into account. This will be fixed in the next P3 firmware release.
kind regards,
Paul N6HZ
--
View this message in context:
I picked up a P3 kit last week, put it together for FD.
Took it up to Bonny Doon and had it in our CW station.
We (several operators) observed a strange behavior.
With the bandspread opened to 200kHz, and with noise floor ~ -130dB, there
seemed to be a broad hump of noise on the upper half side
, February 22, 2009 4:40 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] Strange behavior when tuning around with SUB receiver
LINKED
Dear group,
Someone please explain to me what's happening with my K3. I have both main
receiver and sub receiver linked. This way, I can tune the sub
Dear group,
Someone please explain to me what's happening with my K3. I have both main
receiver and sub receiver linked. This way, I can tune the sub receiver
with the main VFO knob. However, there's something weird going on when I
cross some sort of band edge.
For example, if both VFO
Another thing I noticed that when near the 5Mhz band, other knobs like the
filter knobs will also induce this motorboat noise when turned. Any
suggestions on how to fix?
73,
James KC2UEE
Also, and possibly another more concerning issue is that when the sub
receiver is on, and I'm tuning
James,
What rev of firmware are you using? I went through test on all of
them I could with the subreceiver, which I didn't install until 2.72
was current. I can't duplicate your results with 2.82. It may not be
a firmware-related issue (or issues).
In the first problem statement, it sounds
My K3 does this sort of unexpected leap to next band up/down at tuning
breaks with linked or unlinked main/sub. I assumed this was because I
had the general coverage filter in the main but not the sub. Firmware 2.82.
No 'zipper' noise here except that little bit at the bottom end of 6m.
73
] Strange behavior when tuning around with SUB
receiverLINKED
James,
What rev of firmware are you using? I went through test on all of
them I could with the subreceiver, which I didn't install until 2.72
was current. I can't duplicate your results with 2.82. It may not be
a firmware-related issue
Here is a link to a video I made showing the problem. You will need VLC to
view the file as it was shot using a webcam on a linux laptop and I did not
have a converter.
http://jamespaulsarte.com/temp/k3.ogv
Please advise!!! I hope that there's nothing wrong with my K3.
73,
James KC2UEE
--
James,
I, too, have noticed what I believe you are noticing. It seems to me
that the jumps in the tracking of VFO A and VFO B occur at the
transitions of the bandpass filters. It is as if when the bandpass
relays switch, the VFOs lose their synchronization. (Of course, I
could be wrong,
Looks like I may not be sticking to my explanation after all. Try
this and see what you get:
WITHOUT the SUB Receiver linked, tune the main receiver to 6.000.000
MHz. Be sure you can see the frequency of the Sub Receiver on VFO B
area and the tuning rate is FINE.
Push AB twice to
...@mailman.qth.net] On Behalf Of William Evans
Sent: Sunday, February 22, 2009 7:54 PM
To: William Evans
Cc: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] Strange behavior when tuning around with SUBreceiver
LINKED
Looks like I may not be sticking to my explanation after all. Try
this and see
Hi David,
I have the 10 watt version and I've noticed that mine jumps between the
frequency and power display setting every once in a while. It will also jump
between frequency and keyer speed setting too. It doesn't happen very often
and when it does, I just ignore it. I figure it's just
Hello all
My K2 has begun to flash back and forth between power reading and frequency.
When the power setting is above 10 watts KPA ON I assume.
When you change the vfo it will flash between power and Freq sometimes.
Also with the power display showing it only reads 68 watts flickering 69 watts.
Hi,
I have some strange behavior of K2 462 on PSK31. I set the power level at
15 watts and advance the drive through a combination potentiometer and the
sound card output until I get 5 watts output. The interface is homebrew
per QST May 99. The ALC is not functioning. Using r or r rev
25 matches
Mail list logo