On Thu, Oct 27, 2016 at 8:31 PM, Walter Underwood
wrote:
> ...S2 noise was silent, even on a wilderness peak
>
===
Nothing new. John Keats noted this in 1816, when he and his fellow SOTA ops:
"...looked at each other in wild surmise,
Silent upon a peak in Darien."
Tony KT0NY
ut one s-unit lower noise due to less gain than
> the Gasfet.
>
> But with "two bars" if you actually measured noise power it would probably
> still be about -120 dBm or higher. Still on HF that is *quiet*.
>
> 73, Ed - KL7UW
>
> From: Walter Underwood
>
quot;two bars" if you actually measured noise power it would
probably still be about -120 dBm or higher. Still on HF that is *quiet*.
73, Ed - KL7UW
From: Walter Underwood
To: Elecraft@mailman.qth.net
Subject: Re: [Elecraft] [K3] The Way We Rank Receivers (long)
> On Oct 25, 2016, a
What he said
Has got me rethinking my approach somewhat.
I still believe I have the optimum transceiver (k3) available given I will
never rely on software to control my dx chasing.
Gary
On Oct 28, 2016 05:55, "Lewis Phelps" wrote:
Al, thanks for a very informative and helpful discussion. Thi
Al, thanks for a very informative and helpful discussion. This sort of posting
is what makes the Elecraft listserv so valuable.
Lew N6LEW
> On Oct 24, 2016, at 10:21 PM, Al Lorona wrote:
>
> Receivers are always ranked by the "2 kHz third order dynamic range", such as
> at: http://www.remeeu
The main commercial interests in subjective audio noise reduction,
particularly for speech, are probably the hearing aid industry.
It is subjective because noise reduction only really removes noise that
isn't interfering. That is still useful, as whilst the human brain can
also do that, it ge
OK, I can't resist. I turned on my KX3 at about 0018z on Oct 26.
It was set up for 20M PSK tuned to 14.070 with a DSP bandwidth
of 2.5KHz. I showed one bar (S1) of S meter with occasional
flashing of the second bar (S3). The preamp was off and it was
in DATA A mode. The antenna is a 2 element w
Oops, that is Willson Peak (yes, double-L) and it is 2-3 miles to the nearest
house.
wunder
K6WRU
Walter Underwood
CM87wj
http://observer.wunderwood.org/ (my blog)
> On Oct 25, 2016, at 2:43 PM, Walter Underwood wrote:
>
>
>> On Oct 25, 2016, at 2:31 PM, Edward R Cole wrote:
>>
>> I wonder
> On Oct 25, 2016, at 2:31 PM, Edward R Cole wrote:
>
> I wonder where in the world one sees a 20m noise floor that low when antenna
> is connected? Only when I lived off the grid running on battery power did I
> see S0 noise on my radio (3.9-KHz with TS180S from a dipole).
Good point. Look
Most of this very interesting post is not-relevant to my ham radio
operating (eme on VHF+).
Comments preceded by asterisk * inserted below:
-
Date: Tue, 25 Oct 2016 05:21:20 + (UTC)
From: Al Lorona
To: Elecraft Reflector
Subject: [El
I assume that Don means a 30Hz wide peak below.
While I have found APF to be good for digging out weak CW
signals near the noise level, I have found a 50-100Hz bandwidth
works better when there are nearby strong signals. (I have the
250Hz crystal filter.) The K3 won't let me narrow the DSP fil
All,
While the suggestions of simulating contest conditions for testing may
have merit, I believe the existing tests demonstrate that the low phase
noise of the K3(S) allows you to 'saddle up' closer to an offending
station in a contest or DX Pileup. The 2kHz test results does indicate
that
There is another frontier. That is noise/RFI reduction.
The Pandora's box of RFI has been opened and can't be shut at this point.
We need to address the issue of noise reduction and noise blanketing in
some quantitative way to compare various RX's. Right now the
"comparisons" are all innuendo
Before I bought my K3, I discussed the radio with someone in the
booth at Radiofest, a small hamfest held near Monterey, CA.
After I had learned a very little bit about the radio, I had my
wife (KI6SLX), a retired QA engineer for Apple, discuss UI
issues. When she said it seemed OK, I wrote a c
EXCELLENT excellent excellent post...Great summary. The listen ability and
ease of ergonomic operability are the reason I love radios with knobs. This
is what the maestro is trying to do for for the Flex 6XXX radios. There is
just not a better box for both on the market other than the K3, K3s, KX3,
Al,
As a CW op, I consider the 2 KHz away figures interesting not really
relevant.
I want to know how well a receiver is able to separate a weak signal
from strong signals 50-100 Hz away. It would be interesting to speculate
how such a measurement would be done. Let the RX use whatever analo
Nice explanation Al. It's nice to know that the K3 ranks high on the
charts, but I agree that 'usability' and 'listenability' are underrated.
Before I purchased my K3, I went to AES in Wickliffe and listened to
several receivers. I liked the sound of the Kenwoods, but I liked the
'modularity' of
17 matches
Mail list logo