just bought this one:
http://m.ebay.com/itm/182385306454?_mwBanner=1
I hate buying from china because of customs, duties and transport effect on
greenhouse gasses, but I couldnt find anything similar with producers like
meanwell - anybody knows why they dont have 80V 10A in theirs offer?
I think
On 22 December 2016 at 06:22, Gene Heskett wrote:
> This is right after the loadrt hostmot2 line. And while it works
> perfectly in the halrun;halcmd scene, it fails in the hal file in
> exactly the same manner.
>
> loadrt hm2_rpspi config="num_pwmgens=1 num_encoders=1 num_stepgens=2"
Try it wi
On Thursday 22 December 2016 05:15:20 andy pugh wrote:
> On 22 December 2016 at 06:22, Gene Heskett
wrote:
> > This is right after the loadrt hostmot2 line. And while it works
> > perfectly in the halrun;halcmd scene, it fails in the hal file in
> > exactly the same manner.
> >
> > loadrt hm2_r
On 22 December 2016 at 12:44, Gene Heskett wrote:
> it still fails and that logfile is attached. The loadrt line is complete
> with config= argument. I'll take that back out. No diff, not even in the
> logfile.
I think you might need to reboot after a failed attempt, there is no
guarantee that ev
Did you see these?
http://www.antekinc.com/
They used to sell on Ebay as well.
Dave
On 12/22/2016 4:06 AM, Klemen Živkovič wrote:
> just bought this one:
>
> http://m.ebay.com/itm/182385306454?_mwBanner=1
>
> I hate buying from china because of customs, duties and transport effect on
> greenhouse
On 2016-12-22 14:12, andy pugh wrote:
> On 22 December 2016 at 12:44, Gene Heskett wrote:
>> it still fails and that logfile is attached. The loadrt line is complete
>> with config= argument. I'll take that back out. No diff, not even in the
>> logfile.
> I think you might need to reboot after a f
On 2016-12-22 13:44, Gene Heskett wrote:
> it still fails and that logfile is attached. The loadrt line is complete
> with config= argument. I'll take that back out. No diff, not even in the
> logfile.
Gene,
please reset only the 7i90 (disconnect and reconnect from power) and then retry
the linu
Yes I see they offer:
http://www.antekinc.com/ps-8n80-800w-80v-power-supply/
but for me to import from USA is nearly the same as importing from CHINA.
Do they have european division?
On Thu, Dec 22, 2016 at 2:39 PM, Dave Cole wrote:
> Did you see these?
> http://www.antekinc.com/
> They used to
On Thursday 22 December 2016 08:12:54 andy pugh wrote:
> On 22 December 2016 at 12:44, Gene Heskett
wrote:
> > it still fails and that logfile is attached. The loadrt line is
> > complete with config= argument. I'll take that back out. No diff,
> > not even in the logfile.
>
> I think you might
On 22 December 2016 at 14:03, Gene Heskett wrote:
> I did, no diff. The failure to load the hm2_rpspi driver, which according
> to its man page, is specific to the 7i90HD board and doesn't need a
> BOARD or firmware= argument, is specific to the linuxcnc environment,
Are you definitely loading Ho
On Thursday 22 December 2016 08:47:27 W. Martinjak wrote:
> On 2016-12-22 14:12, andy pugh wrote:
> > On 22 December 2016 at 12:44, Gene Heskett
wrote:
> >> it still fails and that logfile is attached. The loadrt line is
> >> complete with config= argument. I'll take that back out. No diff,
> >>
On 2016-12-22 15:12, andy pugh wrote:
> On 22 December 2016 at 14:03, Gene Heskett wrote:
>> I did, no diff. The failure to load the hm2_rpspi driver, which according
>> to its man page, is specific to the 7i90HD board and doesn't need a
>> BOARD or firmware= argument, is specific to the linuxcnc
On Thursday 22 December 2016 08:56:17 W. Martinjak wrote:
> On 2016-12-22 13:44, Gene Heskett wrote:
> > it still fails and that logfile is attached. The loadrt line is
> > complete with config= argument. I'll take that back out. No diff,
> > not even in the logfile.
>
> Gene,
>
> please reset onl
On Thursday 22 December 2016 09:12:42 andy pugh wrote:
> On 22 December 2016 at 14:03, Gene Heskett
wrote:
> > I did, no diff. The failure to load the hm2_rpspi driver, which
> > according to its man page, is specific to the 7i90HD board and
> > doesn't need a BOARD or firmware= argument, is spe
On 2016-12-22 15:45, Gene Heskett wrote:
> On Thursday 22 December 2016 09:12:42 andy pugh wrote:
>
>> On 22 December 2016 at 14:03, Gene Heskett
> wrote:
>>> I did, no diff. The failure to load the hm2_rpspi driver, which
>>> according to its man page, is specific to the 7i90HD board and
>>> doe
On Thursday 22 December 2016 09:38:08 W. Martinjak wrote:
> On 2016-12-22 15:12, andy pugh wrote:
> > On 22 December 2016 at 14:03, Gene Heskett wrote:
> >> I did, no diff. The failure to load the hm2_rpspi driver, which
> >> according to its man page, is specific to the 7i90HD board and
> >> doe
On 2016-12-22 15:58, W. Martinjak wrote:
> As I can see, your linuxcnc version is 2.8.0-pre1-2771 and my version is
> 2.8.0-pre1.2762 maybe your's broken.
> Will check this.
>
> Yes living on the bleeding edge is dangerous... ;)
>
'can give an all-clear for 2.8.0-pre1-277.
It works flawlessly her
On 22 December 2016 at 14:33, Gene Heskett wrote:
> Can the 7i90 in epp mode talk to a 5i25 at usable speeds?
No, not at all. Because a 5i25 is not an EPP parallel port.
You would connect the 7i90 to the actual parallel port of the PC, and
save the 5i25 for a different project.
--
atp
"A motor
On 22 December 2016 at 16:05, W. Martinjak wrote:
> 'can give an all-clear for 2.8.0-pre1-277.
> It works flawlessly here.
Could you clone that SD card and send Gene the image?
--
atp
"A motorcycle is a bicycle with a pandemonium attachment and is
designed for the especial use of mechanical gen
On Thursday 22 December 2016 11:13:04 andy pugh wrote:
> On 22 December 2016 at 16:05, W. Martinjak
wrote:
> > 'can give an all-clear for 2.8.0-pre1-277.
> > It works flawlessly here.
>
> Could you clone that SD card and send Gene the image?
great idea Andy, but this isp I have would bounce it,
I was running a program last night on my milling machine. I was cutting
air at the time and saw something that I did not like. I hit the stop
button in gmoccapy and the program stopped but then the tool plunged
downward in the z direction. I found this very odd. I took a look at the
tool offset
> > To run ". rip-environment" at the prompt and also run glade from same
> > prompt after rip-environment was the trick.
> >
> > Now it works, already toggled my first hardware pin and build a user
> > interface should be a simple task or in some cases very simple.
>
> Sounds good, except rip-env
On Thursday 22 December 2016 14:17:40 Nicklas Karlsson wrote:
> > > To run ". rip-environment" at the prompt and also run glade from
> > > same prompt after rip-environment was the trick.
> > >
> > > Now it works, already toggled my first hardware pin and build a
> > > user interface should be a s
User interface seems rather simple although I have some problem with widgets to
get numbers into linuxcnc. I almost got something useful to test machine
manually but for real machining programming is needed.
Happen to know any more or less g-codes for these motions? g-codes for control
of flush
On 2016-12-22 21:58, Gene Heskett wrote:
> I got that, but I'm still configuring a fresh sd card, and Michael's site
> at deb.machinekit.io is DIW. No response to a ping. So I've done the
> dist-upgrade, but don't even think about letting it install a new
> lightdm.conf, it totally wrecks the
On Thursday 22 December 2016 19:54:37 W. Martinjak wrote:
> On 2016-12-22 21:58, Gene Heskett wrote:
> > I got that, but I'm still configuring a fresh sd card, and Michael's
> > site at deb.machinekit.io is DIW. No response to a ping. So I've
> > done the dist-upgrade, but don't even think about
Gene merry Christmas
On 12/23/16 00:49, Gene Heskett wrote:
> On Thursday 22 December 2016 11:13:04 andy pugh wrote:
>
>> On 22 December 2016 at 16:05, W. Martinjak
> wrote:
>>> 'can give an all-clear for 2.8.0-pre1-277.
>>> It works flawlessly here.
>> Could you clone that SD card and send Gene
Merry Christmas Nicklas
On 12/23/16 05:12, Nicklas Karlsson wrote:
> User interface seems rather simple although I have some problem with widgets
> to get numbers into linuxcnc. I almost got something useful to test machine
> manually but for real machining programming is needed.
>
> Happen to k
28 matches
Mail list logo
