On Fri, 23 May 2014, Viesturs L?cis wrote:
> Date: Fri, 23 May 2014 13:55:46 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-05-21 0:31 GMT+03:00 Peter C. Wallace :
> (blink red light at power up and then no lights)
Yes, exactly - CR6 (red color) blinks, when power button is pressed to turn
on the computer and then there are no lights at all.
Is there any way to recover?
Viesturs
On Tue, 20 May 2014, Viesturs L?cis wrote:
> Date: Tue, 20 May 2014 19:13:08 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
Hi Peter
> Pretty sure the 5I23 manual pinouts are correct (all even pins are
> grounded on all 50 pin I/O FPGA cards)
It's quite likely that I made a mistakes or misread the manual,
unfortunately I did not investigate this problem in depths, I changed
something and it worked. The machine is
2014-05-20 18:43 GMT+03:00 Peter C. Wallace :
> OK I found the issue, the 5I24 manual has the connectors labled wrong
>
> the correct pinout is:
>
> P4 I/O 0..23
> P3 I/O 34..47
> P2 I/O 48..71
>
Thanks! Swapped cables (I had 7i37 on P4) and got the machine moving in 3
minutes!
Peter, any ideas,
On Tue, 20 May 2014, Florian Rist wrote:
> Date: Tue, 20 May 2014 17:49:03 +0200
> From: Florian Rist
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
>
> Hi,
> I
Hi,
I was just about to suggest it might be caused by wrong labelling
because I had a similar issue with a 5I23 connected to a 7I42TA.
I don't remember exactly what the problem was, but output and GND pins
were mixed up some how, or the output pin numbering - I don't remember.
Maybe you can che
2014-05-20 16:44 GMT+03:00 Peter C. Wallace :
> If you are unable to set any pin low on the 5I24s P3
I created a quick test config, where I set _all_ pins on P2 and P3 as
outputs like this:
...gpio.nnn.is-output 1
All outputs were connected to axis.0.amp-enable pin
The results (measured on bac
On Tue, 20 May 2014, Viesturs L?cis wrote:
> Date: Tue, 20 May 2014 17:20:24 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-05-20 16:44 GMT+03:00 Peter C. Wallace :
>
> What you said before is that you could not set the PWM enables low and
> suggested that there was a problem with the configuration. I verified that
> the same configuration was able to conttrol the enables in my test system.
>
> If you are unable
On Tue, 20 May 2014, Viesturs L?cis wrote:
Date: Tue, 20 May 2014 15:06:01 +0300
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] 5i24?
2014-05-20 0:17 GMT+03:00 P
To: "Enhanced Machine Controller, (EMC)" > >
>> Subject: Re: [Emc-users] 5i24?
>>
>> On May 17, 2014 6:58 PM, "Peter C. Wallace" wrote:
>>
>>>
>>> 7I39 5V power
>>>
>>> You can check the config by looking a
On Mon, 19 May 2014, Viesturs L?cis wrote:
Date: Mon, 19 May 2014 18:17:07 +0300
From: "[ISO-8859-13] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller, (EMC)"
Subject: Re: [Emc-users] 5i24?
On May 17, 2014 6:58
On Mon, 19 May 2014, Viesturs L?cis wrote:
Date: Mon, 19 May 2014 18:17:07 +0300
From: "[ISO-8859-13] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller, (EMC)"
Subject: Re: [Emc-users] 5i24?
On May 17, 2014 6:58
On May 17, 2014 6:58 PM, "Peter C. Wallace" wrote:
>
> 7I39 5V power
>
> You can check the config by looking at the dmesg list or running
>
> sudo mesaflash --device 5i24 --readhmid
Both boards have 4,96 V on pins of 7i39's P1 (both receive power through
flat cable). I checked with multimeter on
On Sat, 17 May 2014, Viesturs L?cis wrote:
> Date: Sat, 17 May 2014 18:25:40 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-05-17 16:58 GMT+03:00 Peter C. Wallace :
>
> Did you set the fault input polarity for all pwmgens?
>
Yes, fault-invert was set to 1 for all pwmgens, so that fault pin would be
"false". I checked and they were all "false". I commented out fault-invert
lines for first 2 instances of pwmgens an
On Sat, 17 May 2014, Viesturs L?cis wrote:
> Date: Sat, 17 May 2014 15:08:13 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-05-16 16:37 GMT+03:00 Peter C. Wallace :
>
>
> Did you power cycle the CPU after flashing the card?
No, I didn't. Manual does not say that it should be done.
Anyway, I tried today and it kind of seemed to be allright, it even moved
both motors on one of the 7i39s. I just have no idea, what k
On Fri, 16 May 2014, Viesturs L?cis wrote:
> Date: Fri, 16 May 2014 07:50:30 -0400
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-05-16 7:50 GMT-04:00 Viesturs Lācis :
> The problem is with pwmgens - it seems to me that there are 1-phase
> pwmgens in this firmware file
The whole pinout in dmesg is obviously wrong (3 pwmgens, 3 encoders and 1
stepgen enabled in INI file):
[ 2182.566925] hm2/hm2_5i24.0: 72 I/O Pins used
t;Enhanced Machine Controller (EMC)" >
> > Subject: Re: [Emc-users] 5i24?
> >
> > I finally received 5i24 board, but I am stucj at getting LinuxCNC to
> > cooperate with it.
> > I have 2.7.0-pre0.43... and I am getting an error:
>
> There is a patch th
On Wed, 14 May 2014, Viesturs L?cis wrote:
> Date: Wed, 14 May 2014 06:54:46 -0400
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i
hine Controller (EMC)"
> >
> > To: "Enhanced Machine Controller (EMC)" >
> > Subject: Re: [Emc-users] 5i24?
> >
> > 2014-04-11 6:22 GMT+03:00 Peter C. Wallace :
> >
> >>> 1) do I understand correctly that firmware for 2x 7i39s and
On Fri, 11 Apr 2014, Viesturs L?cis wrote:
> Date: Fri, 11 Apr 2014 10:26:02 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-04-11 6:22 GMT+03:00 Peter C. Wallace :
> > 1) do I understand correctly that firmware for 2x 7i39s and few stepgens
> is
> > not that demaning and also smaller fpga of 5i24 will handle it with ease?
>
> It will fit easily (the 5I24-16's FPGA is about 2x the size of the 5I23
> FPGA)
And 5i2
On Thu, 10 Apr 2014, Viesturs L?cis wrote:
> Date: Thu, 10 Apr 2014 12:11:43 +0300
> From: "[UTF-8] Viesturs L?cis"
> Reply-To: "Enhanced Machine Controller (EMC)"
>
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] 5i24?
2014-04-10 5:26 GMT+03:00 Peter C. Wallace :
>
> Each card has different firmware. If you download the 5i24.zip file from
> mesa, you can see the available bit files (note that there are two 5I24
> models
> with differing FPGA sizes, the 5I24-16 and the 5I24-25, each have their
> own bifiles)
My
On Wed, 9 Apr 2014, Viesturs L?cis wrote:
Date: Wed, 9 Apr 2014 14:56:34 +0300
From: "[UTF-8] Viesturs L?cis"
Reply-To: "Enhanced Machine Controller (EMC)"
To: "Enhanced Machine Controller (EMC)"
Subject: Re: [Emc-users] 5i24?
Ok, thanks!
How about fir
Ok, thanks!
How about firmware for 5i24? Can I take the same vhd file you compiled for
me for 5i23, change there the board number and would it work? Are you aware
of the differences between 5i23 and 5i24? I see that they both have 3x 50
pin connectors and that is about all that I understand. I rec
On 4 April 2014 20:42, Viesturs Lācis wrote:
> I saw in Mesa homepage that there is 5i24 board.
> According to its manual it seems like a possible drop-in replacement of
> 5i23 card, if correct firmware is provided.
> Is it supported by LinuxCNC (hostmot2 driver)?
http://git.linuxcnc.org/gitweb?
Hello!
I saw in Mesa homepage that there is 5i24 board.
According to its manual it seems like a possible drop-in replacement of
5i23 card, if correct firmware is provided.
Is it supported by LinuxCNC (hostmot2 driver)?
Viesturs
-
32 matches
Mail list logo