Cornfirm! No vox possible.
73, martin dl1fux
Am 01.07.2010 00:35, schrieb Tim Ellison:
Bob,
As indicated in the letter you received with your FLEX-1500, the multiple audio
driver issue is temporary until the FLEX USB streaming audio driver has the
bugs worked out and can be used instead.
The main thing it to think of the PC *and* the SDR hardware as one radio
system; not two separate components. You must ground both to a single point
ground with a low impedance, non-resonant RF ground to earth if you use
unbalanced antennas and/or operate in the near field of the antenna.
-Ti
I experienced the same thing this weekend in a portable situation during
Field Day (note I am an 8 day newbie, so no expert).
From home, with a good ground system and resonant ant, no problem.
But, out in the park for Field Day, with the only a 3ft rebar driven
into the ground for a ground, a
Bob,
As indicated in the letter you received with your FLEX-1500, the multiple audio
driver issue is temporary until the FLEX USB streaming audio driver has the
bugs worked out and can be used instead. In the mean time, use what works the
best for you and your PC setup.
There may be a bug in
Received my Flex-1500 June 28 and have some comments about the set-up. My
computer is a new dual-core processor running Windows 7. Initial set-up went
all okay except for the CW mode. I installed PowerSDR v2.0.3 and had very rough
sounding CW sidetone and the signal also sounded very choppy with
Is anyone using an F5K with a dual receivers in SO2R like operation?
Preferably with one amplifier?
If so, could you contact me offlist? I'm undertaking a major overhaul
of my station including the antenna farm and would like to swap notes
and gain from prior experience.
Thanks!
Stu K6TU
Ray - K9DUR wrote:
Alf,
On the SDR-1000 the PA only covers 160m-10m, so the 6m output is always
~0.5W. Yes, the SDR-1000 really needed a pre-amp for 6m receive.
Thanks for the info. I probably knew that, but had forgotten. I use my
SDR1K as a test receiver and to drive transverters. I orig
I have a SDR-1000.
The SDR-1000 PA does not cover 6M. The output on 6M is the same as a
unit without the PA.
73,
Bill
NJ1H
On 6/30/2010 12:09 PM, Alfred Green wrote:
y...@aol.com wrote:
Here is my question, Have a 1000 that Iam giving to one of the kids
in our club. He asked me about 6 mete
Alf,
On the SDR-1000 the PA only covers 160m-10m, so the 6m output is always
~0.5W. Yes, the SDR-1000 really needed a pre-amp for 6m receive.
73, Ray, K9DUR
http://k9dur.info
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.f
y...@aol.com wrote:
Here is my question, Have a 1000 that Iam giving to one of the kids in our
club. He asked me about 6 meters,as he worked that band as a tech. I looked
thru the forms and the KB didn't see much about the 1000 and six meters. I
never used the radio on 6 and do not remember. I
Here is my question, Have a 1000 that Iam giving to one of the kids in our
club. He asked me about 6 meters,as he worked that band as a tech. I looked
thru the forms and the KB didn't see much about the 1000 and six meters. I
never used the radio on 6 and do not remember. I realize the rig has
Dear FLEX-1500 customers:
As reported last week, we are now shipping the FLEX-1500 in significant
volume. The first production run will complete shipment this week and the
second run is on the SMD line right now. We expect the second production
run to start shipping by the end of next week. The
I am running a Flex3000 with v. 1.18.3 (waiting for 2.0), using a Heil HM-5
mike. Mixer is set to full slider; Mike Gain to 20, no CPDR or DX to do
this test. When I transmit using TX EQ (and a nominal preamp setting) folks
have told me that voice is normal for first few seconds, then there is
spl
Larry,
There is another way to get out of demo mode. Go to the
Setup>General>Hardware Configuration tab and select the correct radio. Shut
down and reload PowerSDR and you will be back up and running. Reset
database always works but you loose all your settings unless you save and
restore your n
14 matches
Mail list logo
