Re: [Flexradio] Setting Power Levels for Digital Modes on 5000A

2011-11-14 Thread Brian Lloyd
On Mon, Nov 14, 2011 at 3:35 PM, Jerry Gardner wrote: > What is the best way to set output power levels for digital modes? I can > think of two possibilities: > > 1. Set Drive to 100 and adjust TxGain until ALC reads 0 dB. Then set output > power level by adjusting the Drive slider. > > 2. Leavin

Re: [Flexradio] Setting Power Levels for Digital Modes on 5000A

2011-11-14 Thread Dave Beumer WØDHB
Jerry Check out http://kc.flexradio.com/KnowledgebaseArticle50363.aspx?Keywords=digital+mode +levels Dave -Original Message- From: flexradio-boun...@flex-radio.biz [mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Jerry Gardner Sent: Monday, November 14, 2011 4:36 PM To: FlexRadio

[Flexradio] Setting Power Levels for Digital Modes on 5000A

2011-11-14 Thread Jerry Gardner
What is the best way to set output power levels for digital modes? I can think of two possibilities: 1. Set Drive to 100 and adjust TxGain until ALC reads 0 dB. Then set output power level by adjusting the Drive slider. 2. Leaving Drive set to 100 and adjusting TxGain to set the power output on t

Re: [Flexradio] Setting up MixW

2011-11-14 Thread Keith Goobie
Hi Mike Here is some guidance / input. >So for example - SET VPSE split Com 7 Com 8 > >Select in Mix W Configure PTT & CAT = CAT = Kenwood >Model = TS-200 >In the PTT & CAT interface window in MIX W = Com8 (9600) >What settings are to be used in the Flex Cat setting and what is ch

[Flexradio] Band Decoder for Power SDR

2011-11-14 Thread Clyde Washburn
Yes, I am using a microHam StationMaster with my Flex-5000A -- I use DDutil talking to PowerSDR, and have the hardware com port driving the StationMaster on the Repeater output of DDutil, on the RCP setup tab. Works great. I also use com0com to create two pairs of virtual com ports -- one pair

[Flexradio] Setting up MixW

2011-11-14 Thread Michael
I wonder if any one has set up VPSE , MIX W , VAC with the Flex 5000A in Windows 7 64 bit. I have VAC working Mix W with no trouble. I have VPSE working and can generate com ports that can be seen within the CAT settings of the Flex menu. I seem unable to get Mix W to PTT the radio. I can get t

Re: [Flexradio] FlexRadio Digest, Vol 79, Issue 13

2011-11-14 Thread K Andrey
Thanks for the letter! I shall soon answer you! I am engaged http://www.transcar.com.ar/images/axerv.html Jessya ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: h

Re: [Flexradio] PSDR & MMTTY

2011-11-14 Thread Brian Lloyd
On Mon, Nov 14, 2011 at 8:34 AM, Peter E. Beedlow wrote: > I've read the Wiki, searched the Knowledge Base and searched this forum but > haven't found an answer to my question. > > Is it possible to run MMTTY using FSK with PSDR? > > Yes I've read all the arguments, AFSK works fine but my preferen

Re: [Flexradio] PSDR & MMTTY

2011-11-14 Thread Ray, K9DUR
Peter, >From one viewpoint, PowerSDR does not support true FSK operation in that it does not shift the frequency of the master oscillator. However, it is a software-defined radio. When properly adjusted (carrier & sideband suppression, modulation level, etc.), the signal produced, while technica

[Flexradio] PSDR & MMTTY

2011-11-14 Thread Peter E. Beedlow
I've read the Wiki, searched the Knowledge Base and searched this forum but haven't found an answer to my question. Is it possible to run MMTTY using FSK with PSDR? Yes I've read all the arguments, AFSK works fine but my preference to use FSK! Hardware is a 5000C with Windows XP as the OS and th