In response to N4ZVN, I and others have received similar reports. I have tried
different mics, buffer settings, eq settings, tx bandwidth settings, ferrites
on all cables with special attention to firewire cable, different firewire
cards, different final bias settings all with no change to the
Tim and Jeff, thanks for the reply. I have tried using the balanced lin input
on the rear of the radio, along with the front mic connection, both with the
same results. I have operated the radio with and without any eq or compander,
both with the same results. I have also monitored my signal
Running 1.17.0 svn ver. 2635 and the TX meter goes to full scale when in
alc,mic,cpdr,eq. lev etc when operating-goes to 200 db when radio is keyed, is
anyone else seein the same thing?
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
Is anyone been able to run the latest PowerSDR with firmware version 1.3.0.0?
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives:
Thanks for the responses. I have reset the database and rebooted computer
several times.
Dave-W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives:
I am using XP Home Edition. I have a dual boot setup and am going to try it
out on Vista. Will let you know result.
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
I returned home this eve from work, fired up the radio and it is working
correctly. I had previously rebooted the radio with no effect. Go figure.
Thanks for all the help.
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
I just installed new console,firmware and firewire driver. Main receiver works
as normal. 2nd Receiver comes up on the screen but no signals present. I have
in the ant menu the rx1 tap checked. Firmware 1.2.1.10. Before installation
of new software and firmware all worked as normal.
What
In reference to the KB article on Ver 3.2.0, where can one obtain the mentioned
Firewire Hardware Device Driver? The version on the Flex Radio web page is
version 3.0.0.70.
Dave-W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
Tim, thanks for the report on the status of the new firewire driver.
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives:
Tim - I only have the problem when I change to 6 meters on antenna connections
1 2. If I am on 80 meters and switch to 6 meters and then back to 80 I show
a high SWR. If I am on 80 meters and switch to any other band with the
exception of 6 meters it shows a 1 to 1 swr in tune. When I start
I am having trouble with the radio transmitting into the selected antenna
connection. The radio is set it to coax 1 and to 80 meters. When I switch
bands and then go back to 80 meters and transmit I am seeing a high SWR, then
switch between ant 1,2,3 and set then set back to ant 1 it has a
Neal, I only hear relay clicks on changing the receive antenna selection but
not when the transmit antenna is changed.
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Tim - I believe I did that when I first noticed it, but I will try that again.
Dave
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
Archives:
Tim - I deleted the database and restarted radio, still have the same problem.
I also ran the firmware upgrade for the series 34 rfio over again with no
change. Should I be hearing a click from the relays when I change the TX
antenna port?
Dave
___
Operating on 75 meters for about 4 hours, the receiver locked up once, I
also noticed a high SWR warning when transmitting into a known 1 to 1
match, but just one time in 4 hours of operation, then the radio locked
up again after further operation and would not receive and would not
reset by
Downloaded the new firmware 1.1.10, SVN 2000, keyed and unkeyed radio
with MOX many times(30) no drop out of receive, until joining a QSO
then after several transmissions the drop out returned. Could it be
that when RF is present it causes the problem?
Dave-W4DWG
I disconnected my Griffin Powermate and the problem still persists. I
am running 1.10.4 SVN 1963, P-4 3.2 , L-2cache , 2 gig RAM. I use VOX
so when it hangs up I tap the mic to clear problem. I can find no
consistency to the problem. I can go for several transmissions with no
problem and
Jeff: I have noticed the very same thing concerning seeing high SWR at
the Flex 5000 when I have a 1to 1.
Dave-W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz
I just had the rx drop out during a QSO, listened closely and could hear
signals very much attenuated but they were there.
Dave-W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
Gerald, thanks for your attention and I have no doubt that it will be
taken care of. I wish I could re-create it but it is very random.
Dave - W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
Great to see a new Release with many great changes, would like to see
the ability to change colors and sizes as with K6JCA changes.
Dave-W4DWG
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
1207 and still not here
-- next part --
An HTML attachment was scrubbed...
URL:
http://mail.flex-radio.biz/pipermail/flexradio_flex-radio.biz/attachments/20071113/8f9dc5fb/attachment.html
___
FlexRadio mailing list
Still waiting #1207
-- next part --
An HTML attachment was scrubbed...
URL:
http://mail.flex-radio.biz/pipermail/flexradio_flex-radio.biz/attachments/20071109/8ff71256/attachment.html
___
FlexRadio mailing list
Has anyone been able to use the Cubase software with the Edirol FA-66 and if
how did you set it up?
David Gardner-W4DWG
-- next part --
An HTML attachment was scrubbed...
URL:
http://mail.flex-radio.biz/pipermail/flexradio_flex-radio.biz/attachments/20070202/21fd5625
The KnowledgeBase shows how to set up with the Presonus but can not find info
on the Edirol. Not sure it is possible.
Dave-W4DWG
-- next part --
An HTML attachment was scrubbed...
URL:
I am getting an unhandled exception message whe I try and change the slope
setting for the agc. Seems to have started after svn 686. Any help would be
appreciated.
Thanks,
Dave-W4DWG
-- next part --
An HTML attachment was scrubbed...
URL:
27 matches
Mail list logo