[Flexradio] Test Message Please Ignore

I am just testing the reflector. Doug, VA3CR ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz/ Knowledge

[Flexradio] ATU Problem - Fixed

Please forgive me..this was a senior's moment. The tuner will not work if you put the Tuner on Bypass J All fixed. Happy New Year. Doug, VA3CR ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz

[Flexradio] SDR-1000 Fan Noise

work?) and this solution http://homepage.ntlworld.com/m.rabel/SDR%20Fan%20noise.html wondering also if this one is safe? My guess is this has been discussed before, but any suggestions or thoughts would be appreciated. Doug McCann, VA3CR

[Flexradio] Digital and release 1.12

that is the problem. All suggestions appreciated. Doug McCann, VA3CR ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archives: http://www.mail-archive.com/flexradio%40flex-radio.biz

[Flexradio] SDR-1000 Fan Noise

Thanks for all the tips. I nibbled out the front of the cabinet where the fan seats and it reduced the fan noise considerably. Still not where I would like it, but much better and liveable. Much appreciated. Doug, VA3CR ___ FlexRadio

Re: [Flexradio] SSTV Programs

To: Doug McCann; flexradio@flex-radio.biz Subject: Re: [Flexradio] SSTV Programs Try contacting the Chroma Pix folks - they sent me a program a few years back that lets me point ChromaPix to a specific sound card - think it's called spconf.exe Regards, Bill (kd5tfd) At 01:11 PM 6/9/2008, Doug

[Flexradio] SSTV Programs

. I would really like to use that program, but will settle on an good program that works with the radio. Any thoughts or suggestions would be appreciated. Doug McCann, VA3CR ___ FlexRadio Systems Mailing List FlexRadio@flex-radio.biz http

[Flexradio] X2TR and Pwr Out

I have the SDR-1000 and use a small linear with it. Does anyone know of a way to have the SDR software reduce the power to say 35 watts when the X2TR button is depressed which engages the linear? I am trying to avoid an accidental overdriving as I usually run barefoot and sometime wish to switch

Re: [Flexradio] SSB Tx Audio Punch

I too have the Audio Punch problem. I tried to roll back to 1836 and ran into a lot of error messages. For now, I have settled for the official download 10.1.3 which fixed the audio problem. FYI only Doug, VA3CR www.va3cr.net -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL

[Flexradio] Low Power Output

Since I installed the later SVNs (now at 1853), my power out on SSB peaks around 25watts, instead of what I am used to which is 50 watts. I measure the output using an SWR/PWR meter in a Yaesu FC-902 tuner set to straight thru. I reverted to the BETA 1.9.1 version and it puts out 50watts.

[Flexradio] Mute Button Not Working

I am using SVN 1756 and the MUT is not working. It clicks, but stays the same colour and does not mute the radio. Anyone else having that problem? Is there a fix? Doug, VA3CR -- next part -- An HTML attachment was scrubbed... URL:

[Flexradio] Mute Button Not Working

Sorry about that..it's the 1000 Doug, VA3CR -- next part -- An HTML attachment was scrubbed... URL: http://mail.flex-radio.biz/pipermail/flexradio_flex-radio.biz/attachments/20071124/842f447d/attachment.html ___ FlexRadio

[Flexradio] Mute Button Not Working

Thanks...this fixed the problem. Doug, VA3CR -Original Message- From: Ed Stallman [mailto:[EMAIL PROTECTED] Sent: November-24-07 6:27 PM To: Doug McCann Subject: Re: [Flexradio] Mute Button Not Working Doug , after updating to SVN 1756 the MUT did not work for me either, a few

[Flexradio] Help with Digital Mode and Hamscope

I cannot get my SDR-1000 to transmit on digital. It receives, the rig will key up, and a signal is showing on Hamscope, but there is no drive to the radio nor RF out. My setup is: Edirol, VAC, NV8Com, TRX Manager as logging program that Hamscope uses to key the rig. I have tried the same thing

[Flexradio] Help with Digital Mode and Hamscope

DUH...you have to turn up the TX gain on the Digital Specific controls on the front control panel. I tested the unit again with a lower reading watt meter and found a small amount of RF going out. Then I boosted the TX gain control and voila have output. Band conditions are so bad at the moment,

[Flexradio] Digital Mode Software other than MixW

I tried MixW and while I can get it to work, prefer some of the other programs. Please let me know what other digital mode and SSTV software any of you have had success with using the SDR-1000 Thanks in advance. Doug, VA3CR www.va3cr.net ___

[Flexradio] Flexradio and Hamscope

Has anyone had a successful experience at getting the SDR to work with Hamscope. I can get the receive to work, but not the transmit. Doug, VA3CR ___ FlexRadio mailing list FlexRadio@flex-radio.biz

[Flexradio] Audio Issues

The SDR-1000 is a fantastic radio on receive but I am having some issues with transmitting. The transmit audio just doesn't have any punch and the output power seems to be about half compared to my Yaesu FT1000MP. My watt meter peaks about 25 watts vs 1000MP which peaks about 50 watts on

[Flexradio] SDR Audio Problem

Sometimes when I use the SDR-1000, the audio cuts out and then back on, pulsing like that about once or twice per second. I found a solution, which is to turn off PowerSDR and Turn off my Edirol FA-66, then restart both. It's not a big deal and doesn't do it often, but I was wondering if this is

[Flexradio] SDR Audio Problem

to see if it happens again. Thanks again for the tremendous support. Doug, VA3CR www.va3cr.net -Original Message- From: Eric Wachsmann [mailto:[EMAIL PROTECTED] Sent: January 31, 2007 4:49 PM To: 'Doug McCann VA3CR' Subject: RE: [Flexradio] SDR Audio Problem You may also

[Flexradio] Help with Power Amp Calibration

is invalid... Test Run 4: Now it works OK until 15 Meter Ext/Adv SSB Indicator shows 70% Message: Calculated gain is invalid... Every test SWR on external meter is showing 1.1:1 Power out on external meter is varying with tests but never exceeding 100 watts Doug McCann, VA3CR