Hi all,
I am quite confused about how olpc's codes initialize VGA card.
As far as I know, olpc will use softVG vsm (part of VSA) to initialize
hardware and provide
Interfaces to VGABIOS.
But in the olpc's codes I only see a function graphics_init() to pass
parameters to softVG.
Are there
Well, I search a bit where the #init comes with no luck, it seems to
get down into the deep blue sea :), it seems to come from inner layers
of the board. I would like to be on a mistake but ...
Another option, cut the pin, u, but with which tool?, and worst,
cut without broking any of the
please see my other mail
Mh the other mail seems to be cought in a spam filter or s.t. like that?
ST
--
linuxbios mailing list
[EMAIL PROTECTED]
http://www.linuxbios.org/mailman/listinfo/linuxbios
Hi Beth
Am Donnerstag, 12. April 2007 14:17 schrieben Sie:
Hi all again (hi ST, yes I am Jose, Beth is a long story :D, some day ...).
Nice hearing from you :-)
Well I am a bit disconnected, but, ST are you still interested on
that I check the pins of the second socket?.
Yes! Especially if
On 12.04.2007 14:26, Stefan Reinauer wrote:
* Carl-Daniel Hailfinger [EMAIL PROTECTED] [070412 02:28]:
Note to self: Document that we're using latest lzma sdk and NOT the
p7zip variant, which has incompatible command line syntax and
incompatible compression format.
who is we?
I consider
Hi
I am still puzzled how the second flash chip is to be used on the GA-M57SLI-S4
board. As Peter mentioned LPC is used on this board. Would it be enough to
use the flash chips (for programming and reading) to just disable one chip
with the #init signal? It seems as if only one of the chips
Hi,
I am looking into building a personal workstation around the Tyan S2915
or the Tyan S2927 for LinuxBIOS hacking.
I have been following the mailing list since January when Yinghai Lu
posted a huge patch with support for the Tyan S2912, among other boards.
From Tyan's webpage it seems that the
* Corey Osgood [EMAIL PROTECTED] [070412 05:19]:
Can someone run some tests on getpir and checkpir? Last time I ran it,
about a week ago on the jetway j7f2we1g, getpir came up with a different
checksum than checkpir did.
This means the pirq table is broken.
Also, am I correct in the
Arvind Seshadri wrote:
Hi,
I am looking into building a personal workstation around the Tyan S2915
or the Tyan S2927 for LinuxBIOS hacking.
I have been following the mailing list since January when Yinghai Lu
posted a huge patch with support for the Tyan S2912, among other boards.
From
On Wed, Apr 11, 2007 at 11:08:22PM -0400, Ning (Michael) Qu wrote:
We want to use LinuxBIOS on Tyan s2915. Is there anyone who has
similiar experience? Is it well supported by LinuxBIOS? v1 or v2?
No, it's not supported out of the box. Please check the list of
supported mainboards:
Hi,
Thanks very much! It seems that I should select one from the list...
On 4/12/07, Uwe Hermann [EMAIL PROTECTED] wrote:
On Wed, Apr 11, 2007 at 11:08:22PM -0400, Ning (Michael) Qu wrote:
We want to use LinuxBIOS on Tyan s2915. Is there anyone who has
similiar experience? Is it well
On Thu, Apr 12, 2007 at 06:09:59PM +0200, ST wrote:
I am still puzzled how the second flash chip is to be used on the
GA-M57SLI-S4 board.
Without further investigation of the board, noone but Gigabyte can
say how it's supposed to be used.
As Peter mentioned LPC is used on this board. Would
12 matches
Mail list logo