C8.5
- Balancepoint 32.63 Inch
- Length 44 1/8 Inch
Of course I would love to get some advise regarding another shaft in this
driver to get some of the length back I lost the past years.
Thanks very much in advance !
Leo Noordhuizen - he Netherlands
or total distance?
>
>
>
> Sent from my iPhone
>
> On Jun 25, 2015, at 4:10 PM, Leo Noordhuizen
> wrote:
>
> Hello again,
>
> Earlier today I collected some numbers about my 'swing' and would love to
> get some advise from the much more knowledgeable peo
- 12 deg dynamic loft
- slightly swing inside out (4.3 degrees)
- 1.8 degrees open
- swingpath 0.9 upwards
- Spinning 4300 !!!
I would appreciate it very much if some shafts (on the lighter side of the
spectrum) could be advised
Thank sin advance !
Leo Noordhuizen - Eindh
any advise on how to clean
them up without damaging them more.
I dont dare touching the bad leather wrapped grips as I have no idea
whether they are restorable or that they need to re-gripped. (Which would
not improve the authenticity of the clbs of course)
Thanks for your suggestions :)
Leo
I have a friend who gets 'unwell' from looking at the huge driverheads
which are sold nowadays and he asked me whether I could find a good
driverhead with a smaller size.
I would be quite happy if some of you could point me to a supplier of
those. I assume they are still being made ?
Thanks in adv
t the HIREKO graphite shafts ? Any good ?
Lcn (Leo Noordhuizen)
Op 5 mrt. 2014 19:06 schreef "Tom Flanagan" :
> I bought a lot of Mach 22's. The warehouse and office was close to my
> business. I ordered shafts for a 9 club by freq spread. Precision
> Composites, the
Mach-22 shafts... Very nice shafts. Pity they dont make them any longer...
Leo - The Netherlands
On Wed, Mar 5, 2014 at 8:05 AM, Tom Flanagan wrote:
> I have a pile of single clubs including some "name" brand wedges -
> Cleveland, Vokey, Callawy, etc., and a dozen putters, Pings, and others.
Hello,
I have a number of Mercury Performance Plus R/S Iron shafts and am looking
for the trimming information.
I googled but cannot find much information about them. I assume that they
are not being manufactured any longer.
Thanks, Leo - The Netherlands
matching these key swing elements I mentioned
> above to the bend profile design of the shaft. It cannot and should not be
> done any other way.
>
>
>
> Hope this helps and best wishes in this great game!!
>
>
>
> TOM WISHON
>
>
>
>
>
>
>
> *From:* ow
ce I hit a ball with a 7 iron is a
meagre 145 yards)
I am 65 years of age
Looking forward to any advise you can give me.
Kind regards,
Leo Noordhuizen - The Netherlands
the UNIX operating system, which I used since then. Looking at my
Android-based mobile phone, based on Linux/UNIX, it is sometimes difficult
to really grasp the progress what has been made in 40 years.
Leo Noordhuizen - The Netherlands
On Sun, Jan 31, 2010 at 9:44 PM, Ed Reeder wrote:
> D
some time ago,
and would be happy to play a stepless shaft again.
Looking forward to your comments and advise, with kind regards,
Leo Noordhuizen
The Netherlands
Im sure Tom meant to say that the hands are placed as if putting (putter
grip)
Leo
On Sat, Aug 1, 2009 at 8:59 PM, Marcello Franchi wrote:
> Beware... putter grip on a chipper is illegal too.
>
> Ciao,
> Marcello
>
>
> 2009/8/1 Tom Flanagan
>
> We used to call them "jiggers" or "chippers". 7
available yet...
Kind regards, Leo Noordhuizen
A basic question:
I have a question on preparing metal shafts and
iron heads for the epoxy.
I have no problem at all with the bond between
grapite shafts and iron or wood clubheads.
However Iron heads on iron shafts are getting me
nervous. I am lucky that nobody had yet the surprise of a fl
12 September 2003 7:49 am, Leo Noordhuizen wrote:
> > What is said below about DAT recorders in Europe is complete nonsense.
> > I am from The Netherlands, and have been working a long time for
> > Philips who was (I think) the inventor of the DAT recorder.
> > The DAT recorder
Apologies to all for erroneously requesting a Read Receipt in my previous
messages !
Leo
, Leo Noordhuizen
- Original Message -
From: "Another Happy Linux User" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, September 12, 2003 6:25 AM
Subject: Re: ShopTalk: Please go Here ( very O.T. rant)
>
> One other "small" thing
&
I want to check out the S450 also, but cannot find a source any more.
Are they still being sold ? If so please tell me where ?
Leo Noordhuizen - The Netherlands
- Original Message -
From: <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Friday, September 12, 2003 3:35 PM
I again seek some information: A friend of mine
wants me to build some becu wedges. I cannot find a source for the heads. (I
seem to remember that GolfWorks carried them, but apprantly no any
longer)
Any help is very appreciated.
Regards, Leo Noordhuizen - The
Netherlands
20 matches
Mail list logo