Problem solved. I looked over the information on the waterfall wide graph
window and noticed that the "FLATTEN" button was open while the "RF SPEC"
was checked. Somehow, I must have unchecked the FLATTEN button while
switching to JTAlert-X to catch a CQ station. Once I checked FLATTEN,
signals a
Hi:
Maybe a corrupt driver. If you installed or used another application. I
had problems with my Kenwood 590SG not sure if it was Winlink or a Windows
update. Maybe reinstall drivers (depending on rig). Plug unplug USB
cable.
Just my 2 cents.
73'
Edfel
KP4AJ
On Thu, May 9, 2019 at 8:22 PM Ha
I've had the new 64 bit version go deaf in a similar manner after sitting
unused perhaps 36 hours. Nothing would solve it...rebooted, fixed it
immediately with no changes of any kind.
73, N0AN
Hasan
On Thu, May 9, 2019 at 7:02 PM Ed Deichler wrote:
> Both LINE IN and LINE OUT were previously se
Reply-To: WSJT software development
Date: Thursday, May 9, 2019 at 4:58 PM
To: WSJT software development
Subject: Re: [wsjt-devel] No Longer Decoding
Both LINE IN and LINE OUT were previously set to mono and the program worked
fine. Changing to RIGHT channel made no difference in the
!
Phil
Phil Stephenson
K0PWS
Saint Louis, MO US
636-675-1379
p...@phil-stephenson.com
From: Ed Deichler
Reply-To: WSJT software development
Date: Thursday, May 9, 2019 at 4:58 PM
To: WSJT software development
Subject: Re: [wsjt-devel] No Longer Decoding
Both LINE IN and LINE OUT
Both LINE IN and LINE OUT were previously set to mono and the program
worked fine. Changing to RIGHT channel made no difference in the decoding,
i.e. still a blank waterfall. I'm not sure whether the soundcard is dead
or the K3 output is dead.
Ed
On Thu, May 9, 2019 at 4:52 PM Bill Somerville
On 09/05/2019 16:57, Ed Deichler wrote:
Bill,
Yes. The K3 has respective jacks for line in and line out. According
to the manual, the K3 has two settings for the audio output. NORMAL
is usually used for digital modes and a separate PHONES setting allows
the audio to match headphones and be
Bill,
Yes. The K3 has respective jacks for line in and line out. According to
the manual, the K3 has two settings for the audio output. NORMAL is
usually used for digital modes and a separate PHONES setting allows the
audio to match headphones and be controlled by the AF/SUB gain controls.
Eith
On 09/05/2019 14:52, Ed Deichler wrote:
Bill,
Connection to the K3 is speaker out of computer to line in of the K3.
Disconnecting the cable at the computer stops the waterfall
scrolling. Reconnecting to the computer then restarting the program
restores the scrolling but nothing shows on the
Bill,
Connection to the K3 is speaker out of computer to line in of the K3.
Disconnecting the cable at the computer stops the waterfall scrolling.
Reconnecting to the computer then restarting the program restores the
scrolling but nothing shows on the waterfall.
As I stated in the initial post, e
Ed,
you have now referred twice to the sound card speaker, that has nothing
to do with Rx. How is your K3 connected to your sound card for PC for Rx
audio? Do you have the correct audio input device selected in WSJT-X? Is
that device un-muted in the sound mixer?
73
Bill
G4WJS.
On 09/05/2019
I'm using GA V2.0.1; I erred on the version in my original post. The
Time.is app shows my timing is 0.007 seconds off so accuracy is not the
problem. My soundcard speaker is a Microsoft high-definition audio device
that tests out as working fine.
In my haste I forgot to mention that the waterfal
On 09/05/2019 13:01, Ed Deichler wrote:
I fired up WSJT-X last night only to have decoding suddenly stop after
a few minutes. I was using the rc5 release at the time but a switch
to V2.0.0 GA showed the same results. I checked my soundcard speaker
functions and they test out normal. Several
Deleting the program is often the last resort.
What are you using for a soundcard? Did you check the audio settings in
WSJT-X. Finally, the most currnet GA release is 2.0.1, also available
from the WSJT-X page.
Neil, KN3ILZ
On 5/9/2019 8:01 AM, Ed Deichler wrote:
I fired up WSJT-X last night
I fired up WSJT-X last night only to have decoding suddenly stop after a
few minutes. I was using the rc5 release at the time but a switch to
V2.0.0 GA showed the same results. I checked my soundcard speaker
functions and they test out normal. Several reboots of the computer did
not help. Chang
15 matches
Mail list logo
