Hi Ivan, Thanks much for the links. The Tanner's site is a great resource. Very concise and practical.
I am short-handed at the Plumbing Co. and have little time to work on the silver. I continue to have difficulties adjusting the start conductivity of the water. My incoming tap water has inexplicably changed from about 230 PPM TDS to 24. Our City system is fed by a mixture from a rainwater reservoir blended with several wells with about 14 grains hardness. The still feedwater is supplied by a residential RO unit. It previously has been putting out about 24 PPM and is now down to 11. This has dropped the still output to between 0.1 and 0.2 PPM. This reduces the yield. I have been attempting to adjust start conductivity with CaCO3, a saturated solution which over months continues to rise in PPM, now stabilized at almost 50 PPM. However, when I use this, a bit too much of it causes a runaway (current?) process toward the end of 2.5 hour runs, resulting in beautiful delicate turbinate ( 3 D spirals) pale tan clouds, and some fallout. Sometimes just gray. Also, the electrode plate is much blacker and has faint yellow blotches after a run. Bruce is puzzled. My machine/water is the only one he has seen which does not yield about 10 PPM in 1.5 hours. An unknown ancestor of mine must have disturbed the wrong tomb. At 2.5 hours, I get between 7 and 9 PPM. Can you recommend any resource to find the specific technique for particle size UV absorption tests? Your RGB unit sounds like a good tool. When I get a particle size test(s) made---by whatever method---I could send you a sample to try with the device which might be the beginning of a calibration. Thank you very much for responding to my questions, and let me know whenever it becomes too much of a distraction from your own interests. James Osbourne, Holmes [email protected] -----Original Message----- From: Ivan Anderson [SMTP:[email protected]] Sent: Tuesday, August 31, 1999 7:31 AM To: [email protected] Subject: Re: CS>Ion size was buying CS James, go here : http://www.tannerm.com/electrochemistry/ion_speeds/IonSpeeds.htm Sorry about the math :-/ I don't know who could conduct these measurements, but Zeta potential can be measured in a similar manner. Its a matter of timing the migration of an ion across a field as viewed under a microscope and then plugging the numbers. This looks interesting also: http://www.che.wsu.edu/modules/berquist/electrophoresis.html but may not be of much use. Yes spectrophotometry should work, once calibration has been established. I have made a small immersible unit which uses an RGB led and photodiode, but which is not of much use in definitive measurement until I can find a cheapish way to establish particle size. A non-antibiotic drug habit is whole lot more fun too, so I've been told... Cheers - Ivan ----- Original Message ----- From: James Osbourne, Holmes <[email protected]> To: <[email protected]> Sent: Tuesday, 31 August 1999 10:03 Subject: RE: CS>Ion size was buying CS > Good stuff Ivan... > > Could you direct me to basic info on "The electrophoretic method may be a > better way to determine particle size,..." I have seen the term but cannot > recall how it works. How does the price compare with TEMs?---tests, of > course, not the instrument. > > Also, Bob Berger said that one method of determining particle size is to > measure absorption in the UV range with a Spectrophotometer. > Are you familiar with that technique? If I can get TEM pix of my size, I > might be able to correlate that with UV Spec. readings in some rough sort > of way...enough to verify that I am producing a good sol. Perhaps. > > Of course that means buying a new tube and filter for the old Spectronics > 20. Sometimes I think it would be easier to have a non-antibiotic drug > habit... > > James Osbourne, Holmes > > [email protected] > -- The silver-list is a moderated forum for discussion of colloidal silver. To join or quit silver-list or silver-digest send an e-mail message to: [email protected] -or- [email protected] with the word subscribe or unsubscribe in the SUBJECT line. To post, address your message to: [email protected] List maintainer: Mike Devour <[email protected]> -- The silver-list is a moderated forum for discussion of colloidal silver. To join or quit silver-list or silver-digest send an e-mail message to: [email protected] -or- [email protected] with the word subscribe or unsubscribe in the SUBJECT line. To post, address your message to: [email protected] List maintainer: Mike Devour <[email protected]>

