At 02:05 PM 10/11/2003 -0500, you wrote:
>Ode Coyote. , Mike Monett.
>
>Thank you for all the useful info that you have provided.
>
>I do understand that it will cause agglomeration if we do heat the water
over 110
>degrees. I use a very low constant current. Therefore, I have no
difficulty in getting clear CS.
>
>However, what I understand in reading this sentence, taken from the web
address that I had provided in my first message
>on this subject:
>
>("... The warmer the water, the faster the reaction will take place, and
the smaller the particles will be. ")
#### This statement is in error and is contradicted elsewhere on the same
website where it says the cooler the water, the smaller the particles.
But it doesn't say that when using a constant voltage generator that the
cooler water has a lower conductivity and the ion generation rate and
current density will also be lower with cooler water..and that the total
PPM made in give time will be a LOT lower.
Constant voltage generators have an acceleration curve that starts out
almost flat and goes almost vertical at some point.
Where you start on that curve makes a huge difference in where you wind up
in a given time.
Slight differences in conductivity due to different batches of water or a
few degrees of temperature make great big differences in end product anf
the longer you run it, the bigger the differences.
Like dropping objects off a building, acceleration is feet per minute per
minute and a small difference in height makes a big difference in velocity
on impact.
With a constant voltage generator, PPM calculations are PPM per minute per
minute and can be monitered by the rate of increase of current draw. [One
way to get a handle on a battery pack generator and have some idea of where
to stop before it goes ballistic is to moniter current.]
When using constant current, the initial conductivity of the water may not
allow full set current draw and there will be a ramp up to the set current
that's identical to the slope of the constant voltage setup.
Just a few uS of difference can make many minutes of difference in run
time..even hours of difference.
But once the set current draw is reached, the curve flattens out and
production rates become linear, changing from PPM per minute per minute to
PPM per minute.
>is that, the warmer the water, the smaller the particles will be !
## Not true
isn't it that the warmer the water (above 110
>degrees) the larger the particles will be ?
## True, if they agglomerate by collision. [Might not "always" be true]
>This is what I wanted to find out. My understanding of "agglomeration"
definition
>may be incorrect.
Simply put, agglomeration is the joining of smaller particles into bigger
ones for whatever reason, under whatever conditions.
There are a variety of forces that hold particles apart and a variety of
forces that can overcome the other forces and cause them to join up.
Particles are made from ions that have lost their charge. The closer
together the thus formed particles are, the bigger the cluster they tend to
make. There are forces available that tend to isolate ion/particle clusters
into small groups rather than large ones. [for want of a better term for
transitionary states]. If a number of ions is bonded to a water molecule,
it gets isolated from other water molecules with similar bonds, so when the
particle forms, it only has just so many ions to work with and you get a
very small particle.
Once a particle does form and goes into suspension, the water molecule is
available to catch or hydrate more ions in solution. [My take on it is that
the positive charge of the ion causes the ion to orient itself to the
negative charge of the oxygen atoms in the water molecule, so, they sorta
loosely share electrons.]
The higher the concentration of ions and particles in a given space, the
more likely that isolating forces will be overcome.
In other words, it's not hard to make 3 PPM small particle CS but it
becomes more and more touchy as the PPM exceeds 13 PPM. At over around 30
PPM, we're talking crapshoot and just about anything can kick a batch into
agglomeration mode. [ A little saliva? Some stray ozone? Maybe a touch of
vineger? A fast temperature change? ]
Apparently, the CS-300 is not 'supposed' to make small particle colorless
CS even at 5 PPM and this person goes out of his way to make sure it
doesn't. [even freaks out if it does and includes instructions on how to
prevent it]
The concentration of particles and ions is not uniform in a given
container, tending to be much greater near the electrodes.
Using a low current density limits the rate of ion release in a given area
to a rate that's below the rate that ion/water bonds can be made as a given
local concentration dissipates through Brownian motion, natural thermal
convection currents or mechanical stirring.
If the water is constantly moving, the local concentration doesn't build
up as fast [or not at all] and won't tend to overcome the bonding/particle
formation rate and a higher current density can be used to get the same
smaller particle formations.
But move it too fast and you get high velocity particle collisions with
the electrodes and you get a fuzzy buildup of silver particles on the
electrode. Generally, these impact the hydrogen bubbles and get stuck on
the surface tension of the bubble which stabilizes and weights the bubble
so it won't 'bubble off' or otherwise dissipate and makes the surface of
the bubble a semi conductor..so the bubble grows another bubble and the
process starts over.
The grey fuzzy buildup will grow into the direction of the water flow.
The idea in getting the right water flow rate is to let the hydrogen
bubble off or dissipate faster than you impact them with particles, yet
keep the water moving fast enough to disrupt local concentration zones.
Stirring with a updraft or down draft [vertically], either thermal
convection, pump discharge or bubbler tends to limit [not entirely
eliminate] electrode impacts..or more likely in that case, plateout, better
than vortex stirring sideways [horizontally].
But using bubblers can be sensitive to air componants and if too many
large bubbles are used or the flow rate is otherwise excessive, they'll
blow any particles stuck to the electrodes off into the water making
'sparklies'.
PS, if you do make sparklies or fuzzies, they can easily be filtered out
or otherwise removed.
PPS Sparklies and fuzzies are different from an agglomerated particle as
they are collections of very loosely bonded small particles, not one big
one. Often they will dissipate on their own in time releasing a cloud
that's identical to the original one they came from.
Strictly speaking, all particles over a single atom in size are the result
of agglomeration.
An 'excessively' agglomerated particle will display a color ranging from
yellow [of various shades and densities to include brownish] to violet to
red to green. A oxidized particle will be black and can add hue to other
ranges of particle sizes.
No matter what the color of the water, not all the particles in it are the
same size. There will always be some small ones and ions present. The
depth of color is an indicator of the relative percentages within a given
PPM. For instance, a pale yellow at 20 PPM has many many more colorless
particles than it does the larger ones, as compared to a deep yellow at 20
PPM.
Ode
>
>Gaston
>
>
>
>
>
>
>
>
>
>
>
>
>
>--
>The silver-list is a moderated forum for discussion of colloidal silver.
>
>Instructions for unsubscribing may be found at: http://silverlist.org
>
>To post, address your message to: [email protected]
>
>Silver-list archive: http://escribe.com/health/thesilverlist/index.html
>
>List maintainer: Mike Devour <[email protected]>
>
>