> On Jan 3, 2016, at 1:46 PM, Christian Gauger-Cosgrove > <captainkirk...@gmail.com> wrote: > > Well, I was attempting it with RSTS/E since the "XM0: is missing > ECO's, but will still function." error implies that the DMC11 device > would still function. I turned on debug for the DMC device using "SET > DMC DEBUG" and nothing seems to be getting printed even though the DMC > device is being "used" by RSTS/E.
You need to specify a debug output file, for example "set debug stdout". With that, I see the following: DBG(4762921805)> DMC REG: dmc_rd(DMC0), addr=0x003fe038, SEL0, data=0x8000 DBG(4762921808)> DMC REG: DMC0: Getting SEL0 (0x8000) RUN DBG(4762921808)> DMC REG: dmc_rd(DMC0), addr=0x003fe038, SEL0, data=0x8000 DBG(4762921817)> DMC REG: DMC0: Getting SEL0 (0x8000) RUN DBG(4762921817)> DMC REG: dmc_rd(DMC0), addr=0x003fe038, SEL0, data=0x8000 DBG(4762921820)> DMC REG: DMC0: Getting SEL0 (0x8000) RUN DBG(4762921820)> DMC REG: dmc_rd(DMC0), addr=0x003fe038, SEL0, data=0x8000 DBG(4762921827)> DMC REG: dmc_wr(DMC0), addr=0x003fe038, SEL0, newdata=0x4000, olddata=0x8000 DBG(4762921827)> DMC REG: DMC0: Setting SEL0 (0x4000) MCLR DBG(4762921830)> DMC REG: dmc_wr(DMC0), addr=0x003fe03e, SEL6, newdata=0xa40b, olddata=0x0000 DBG(4762921830)> DMC REG: DMC0: Setting SEL6 (0xa40b) DBG(4762921831)> DMC REG: dmc_wr(DMC0), addr=0x003fe039, BSEL1, newdata=82, olddata=0x40 DBG(4762921831)> DMC REG: DMC0: Setting SEL0 (0x8200) RUN ROMI DBG(4762921837)> DMC TRACE: dmc_svc(DMC0) DBG(4762925339)> DMC REG: dmc_wr(DMC1), addr=0x003fe040, SEL0, newdata=0x4000, olddata=0x8200 DBG(4762925339)> DMC REG: DMC1: Setting SEL0 (0x4000) MCLR DBG(4762925342)> DMC REG: dmc_wr(DMC1), addr=0x003fe046, SEL6, newdata=0xa40b, olddata=0xa40b DBG(4762925342)> DMC REG: DMC1: Setting SEL6 (0xa40b) DBG(4762925343)> DMC REG: dmc_wr(DMC1), addr=0x003fe041, BSEL1, newdata=82, olddata=0x40 DBG(4762925343)> DMC REG: DMC1: Setting SEL0 (0x8200) RUN ROMI DBG(4762925349)> DMC TRACE: dmc_svc(DMC1) DBG(4763203477)> DMC REG: dmc_wr(DMC0), addr=0x003fe038, SEL0, newdata=0x4000, olddata=0x8200 DBG(4763203477)> DMC REG: DMC0: Setting SEL0 (0x4000) MCLR DBG(4763203480)> DMC REG: dmc_wr(DMC0), addr=0x003fe03e, SEL6, newdata=0xa40b, olddata=0xa40b DBG(4763203480)> DMC REG: DMC0: Setting SEL6 (0xa40b) DBG(4763203481)> DMC REG: dmc_wr(DMC0), addr=0x003fe039, BSEL1, newdata=82, olddata=0x40 DBG(4763203481)> DMC REG: DMC0: Setting SEL0 (0x8200) RUN ROMI DBG(4763203487)> DMC TRACE: dmc_svc(DMC0) Event type 4.11, Circuit initialization failure - circuit fault Occurred 20-Dec-28 17:13:27.0 on node 1.43 (SIMH43) Circuit DMC-1 Reason = Circuit synchronization lost Adjacent node address = 0 Event type 4.11, Circuit initialization failure - circuit fault Occurred 20-Dec-28 17:13:27.0 on node 1.43 (SIMH43) Circuit DMC-0 Reason = Circuit synchronization lost Adjacent node address = 0 DBG(5118754449)> DMC TRACE: dmc_poll_svc() That is with two DMCs pointing at each other: sim> show dmc DMC lines=2, connectpoll=2, address=17760070-17760107* vector=300*, 2 units DMC0 attached to 10143, peer=127.0.0.1:11043, speed=0 (unrestricted) MicroDiag=enabled, type=DMC DMC1 attached to 11043, peer=127.0.0.1:10143, speed=0 (unrestricted) MicroDiag=enabled, type=DMC paul _______________________________________________ Simh mailing list Simh@trailing-edge.com http://mailman.trailing-edge.com/mailman/listinfo/simh