-----Original
Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Mark East
Sent: Wednesday, June 25, 2003
2:56 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
What if I replaced them
both with airPoint units? Would that work?
I’ve got almost 50m
of cat5 in conduit that I really don’t want to have to replace with RG-6.
Please tell me there’s a device in the $500-600 range that will do the
job.
I gotta say, I was
totally misled by the reseller. They told me, flat out, that the airBridge
would perform bridging functions. I’m used to working with RadioLAN
products called BridgeLINKs. I saw the pricepoint on the airBRIDGE units and thought I had
discovered a far less expensive alternative. Boy, was I wrong!
Time to change the name,
guys. airClient perhaps? airBridge is waaaaaaaaaay misleading!
-----Original Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Tom Haynes
Sent: Wednesday, June 25, 2003
12:54 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
Sorry, I
just re-read you post. Your setup looks like this (right?)
subnetA
<---> switch <--> ABt(infrastructure) ----------- ABt(adhoc)
<--> switch <--> subnetB
The
normal minimum setup would be this
subnetA
<---> switch <--> AP ----------- AB <--> switch <-->
subnetB
You may
be able to make this work (not fo sure)
subnetA
<---> LAN/router/WAN <--> ABt(infrastructure) -----------
ABt(adhoc) <--> WAN/router/LAN <--> subnetB
If this setup
works there will be sever limitations such as on 64 devices (anything with a
MAC) on either subnet, most peer-peer software will not work, etc...
The only
thing you need to do to your setup is replace the AB closest to NOC with an
APPo. If you use an AP that does not support the address4 field you will have
to replace the switch on subnetB with a router and plug the AB in to the WAN
port.
-----Original
Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Tom Haynes
Sent: Wednesday, June 25, 2003
2:39 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
Use an
airPoint in infrastructure mode to coordinate the whole thing. Or any wireless
router for that matter. How much do you know about wireless networking and
802.11b? This is basic stuff and common to all wireless devices. For that
matter, any networking device. You can't connect three or more computers with
ethernet cards together without a hub, switch or router of some kind. The AP in
this case acts as a hub of sorts.
-----Original
Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mark East
Sent: Wednesday, June 25, 2003
2:29 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
You’ve
got to be kidding me. They market a device that CAN’T be used as a
wireless bridge as “airBridge”???
Please
tell me you’re joking. These devices are already installed. I don’t
even have the boxes they came in!!
Can
someone from smartBridges please weigh in on this??
-----Original Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Tom Haynes
Sent: Wednesday, June 25, 2003
12:19 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
Using
two AB you can only talk between the two computers directly connected to the
AB. You would need to install some form of routing software to send the traffic
beyond the first computer. You miht give 'Internet Connection Sharing' built in
to Windows a try. Otherwise sherch google for personal routing software.
Another idea (don't know if it would work) is to install this
way...
YourNetworkORComputer<-->Router<-->AB<--------->AB<-->OptionalRouter<-->ClientComputer
-----Original
Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mark East
Sent: Wednesday, June 25, 2003
1:56 AM
To: [EMAIL PROTECTED]
Subject: [smartBridges] Using
airBridge TOTAL units as simple Ether bridge
Can anyone help me?
All I want to is use the two
airBridge TOTAL units that I bought as a simple Ethernet bridge (to link two physical
Ethernet networks under the same subnet). If I set one (Unit A) in
Infrastructure mode and the other (Unit B) in Ad Hoc mode, I am able to
associate one with the other. This enables me to ping from Unit A to Unit B
with no problem. I can even ping Unit B from a laptop on the same switch as
Unit A. I cannot, however, ping any devices that are on Unit B’s physical
network from Unit A.
I am going out of the country in six
days and I must get this installation finished for my customer. Can anyone please
tell me, step-by-step, how I setup the two devices to act as a bridge?
Thanks in advance!
-----Original Message-----
From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jerry Carter
Sent: Tuesday, June 24, 2003 10:26
PM
To: [EMAIL PROTECTED]
Subject: Re: [smartBridges]
Outdoor Cat5
I just bought a roll of this
from a guy on ebay (he had a second roll) I hope it's gonna work:)
----- Original Message -----
Sent: Wednesday,
June 25, 2003 12:18 AM
Subject: RE:
[smartBridges] Outdoor Cat5
HEHE I wanted to see that why u no record for a america's
funnies home videos :) Well I use 75$ belkin the blue one its not great cable
but hasn't failed me yet I don't have any ports dieing as of month 2 of using
it, shielded cable down here is too expensive we're talking up to 450$ for 1000
ft I cant afford that sorry :(
Chris
-----Original Message-----
From: Gary Garrett [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, June 25, 2003
12:37 AM
To: [EMAIL PROTECTED]
Actually, the gel is a water block and it keeps water
from wicking along
the pairs if the jacket is damaged.
How would it get damaged? I once
watched a woodpecker pounding away on a
tower for 5 full minutes before I
banged on the tower and he flew away.
I think he just liked the sound it
made when he pecked on it.
Tom Haynes wrote:
>$150-270 per 1000'!!! Holy COW! The gell filled
stuff is for direct burial and
>underground conduit runs. All
you need is the UV resistant kind for above
>ground, outdoor use. Belden
1594A can be found for $55-80 per 1000'
>
>-----Original Message-----
>From:
[EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
On
>Behalf Of Laurence Laforga
>Sent: Tuesday, June 24, 2003
8:31 PM
>To: [EMAIL PROTECTED]
>Subject: Re: [smartBridges]
Outdoor Cat5
>
>
>I just talked to someone at
Graybar and the pricing is $261.64 for
>1000' spool. I hope the
shipping isn't more than $150 with netnimble.
>
>LL
>
>
>
>>Just went through this
since sB is not shipping their radios with
>>
>>
>50'
>
>
>>runs of cat5 anymore (this
is a good thing). John is right, Graybar
>>
>>
>has
>
>
>>1000' spools for about
$120. It's the good, gooey gel-filled type
>>
>>
>that
>
>
>>is harder to crimp, but I
think I'll be glad I'm using it.
>>
>>Laurence Laforga wrote:
>>
>>
>>>Hi,
>>>
>>>Can anyone recommend a
company that sells bulk outdoor Cat5 to use
>>>with the SB outdoor products?
>>>
>>>
>>>
>>The PART-15.ORG
smartBridges Discussion List
>>To Join: mailto:[EMAIL PROTECTED] (in the body
type subscribe
>>
>>
>smartBridges
<yournickname>
>
>
>>To Remove: mailto:[EMAIL PROTECTED] (in the body
type unsubscribe
>>
>>
>smartBridges)
>
>
>>Archives: http://198.63.203.6
>>
>>
>>
>>
>
>Laurence Laforga
>President
>TIRGON Communications
>The PART-15.ORG smartBridges
Discussion List
>To Join: mailto:[EMAIL PROTECTED] (in the body
type subscribe smartBridges
><yournickname> To Remove:
mailto:[EMAIL PROTECTED] (in the
body type
>unsubscribe smartBridges)
>Archives: http://198.63.203.6
>
>The PART-15.ORG smartBridges
Discussion List
>To Join: mailto:[EMAIL PROTECTED] (in the body
type subscribe smartBridges <yournickname>
>To Remove: mailto:[EMAIL PROTECTED] (in the body
type unsubscribe smartBridges)
>Archives: http://198.63.203.6
>
>
>
The PART-15.ORG smartBridges Discussion List
To Join: mailto:[EMAIL PROTECTED] (in the body
type subscribe smartBridges <yournickname>
To Remove: mailto:[EMAIL PROTECTED] (in the body
type unsubscribe smartBridges)
Archives: http://198.63.203.6
