I'd give: http://www.ixiacom.com/enterprise/Chariot.php?section=10#console a try. Grab the console, install it on your laptop, grab the endpoint for the consumer's PC, and get them to run it. Then conduct throughput tests via the chariot console from the backbone side of the AP through to the customer. Should provide you information on throughput TCP/UDP etc.
----- Original Message ----- From: "Blazen Wireless" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, August 15, 2003 2:32 PM Subject: Re: [smartBridges] APPO furstrations.. > 1 queue per customer on the software.. > > > ----- Original Message ----- > From: "Gino A. Villarini" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Friday, August 15, 2003 4:09 AM > Subject: RE: [smartBridges] APPO furstrations.. > > > How are you setting your queques?, the BCU has individual queques, are you > using 1 queque per customer or are you using 1 queque for many customers? > > Gino > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Blazen Wireless > Sent: Friday, August 15, 2003 1:10 AM > To: [EMAIL PROTECTED] > Subject: Re: [smartBridges] APPO furstrations.. > > > I am using a BCU between the t-1 router and the clients > ----- Original Message ----- > From: "Eje Gustafsson" <[EMAIL PROTECTED]> > To: "Blazen Wireless" <[EMAIL PROTECTED]> > Sent: Thursday, August 14, 2003 9:00 PM > Subject: Re: [smartBridges] APPO furstrations.. > > > You need a bandwidth manager on your network and bandwidth limit your > clients. > > Plus if your doing a completely bridge network then you seriously > needs to start doing some routing on your network or else things will > not work. > > Best regards, > Eje Gustafsson mailto:[EMAIL PROTECTED] > The Family Entertainment Network http://www.fament.com > Phone : 620-231-7777 Fax : 620-231-4066 > - Your Full Time Professionals - > eBay UserID : macahan > --- > searchable smartBridges mailing list archive. > http://www.mail-archive.com/smartbridges40part-15.org/ > -- > BW> Okay guys here is a question I know SB says they can have up to 128 > clients associated to the APPO. I have aprox 22 on each one and they are > totally crapping out by that mean I get 4-5 users on > BW> downloading at any given time and I swear to you pings just go to hell > as high as 200-300 and lows about 30ms. I have tried EVERYTHING RTS CTS > different channels WEP no WEP anything and > BW> everything and it has got me by the balls and I am tired of clients > calling me complaining it is slow. It used to be awesome with 4-5 users > total on it and even 10 users but after that its just > BW> gone down hill. > > BW> Any suggestion would GREATLY be appreciated. > > BW> two APPO's each connected to a 500mw Amp 50 ft of coax LMR 400 and then > to a 13DB 90* pac wireless ant one facing north and one facing south both on > chan 3 I know I know you will say interference > BW> from each other I tried separating and it made no difference it actually > got worse I even had one appo in client bridge mode to check interference > and I saw nothing form the APPO right next to it > BW> and very few other Access points out in the field. Most were at rssi 20 > maybe 30% and link 20%. > > > BW> PLEASE PLEASE PLEASE help me with any ideas I am all out I have worked > on this all week I have a remote pop that is fed by the main two APPO's and > the two customers on that radio can ping the > BW> remote appo all day long with less then 5 ms yet when you try and ping > the main appos the pings are all over the place.. > > BW> Oh yea most all signals at eh APPO's from the client show (not sure how > accurate) 80 -100 RSSI some just under 80% and link about the same so I > don't know if this could hamper it I have tried > BW> with a couple clients setting the APPO and ABO to autofallback speeds > and that seemed to help for a couple people that were far out about 4-5 > miles people up close seem to be fine.. > > BW> 13-19db ants on each install > > BW> HELPPPPPPPPPPPPPPPPPPP > > > BW> Martin > > -- > [This E-mail scanned for viruses by Declude Virus] > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
