RE: [smartBridges] Smartbridge Configuration Issue

[Pascal Losier]

Title: Message

Some say I need to replace first ABO with APPO, since it allow more than 64 Mac & APPO will not NAT.   On the ABO at the switch , Do I need to install formware 0.09.10  ???? or is 1.0.08 ???   Or maybe I should really go & install an APPO instead of ABO.   Also, If I use remote management with 0.09.10 do I only loose it for this AB or for complete network pass this ABO ???     -----Original Message----- From: sB Tech Support [mailto:[EMAIL PROTECTED] Sent: Thursday, October 23, 2003 3:06 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Smartbridge Configuration Issue Yes, option #1 is simple in terms of implementation. However, please remember that in order to use PPPOE, you have to "Allow non IP traffic" in the Advance Tab of each aPPO.   Arasu sB Tech Support -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Pascal Losier Sent: Thursday, October 23, 2003 11:40 AM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] Smartbridge Configuration Issue     Is this OK          ???       1.  Fiber...Mikrotik...APPO - - - - - - ABO...(swich)...APPO - - - - - - - ABO...Client PC                        or this     2. Fiber...Mikrotik...APPO - - - - - - ABO...(router)...APPO - - - - - - - ABO...Client PC   I know option #2 is good, but I would like prefer using #1 since no need to installed PPPOE router at other tower.              Yes. The current devices are (APPO & ABO) supports this configuration.  We have already tested this configuration and it is perfectly fine.   POPàABOàRouter(DHCPserver)àAPPOàclients  10.6.0.xx                                             à  192.168.1.XX     Kind regards, Seeni sB Tech support   -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Robin McCaig Sent: Thursday, October 23, 2003 5:44 AM To: [EMAIL PROTECTED] Subject: [smartBridges] Smartbridge Configuration Issue   I got a tower in place that has 2 smartbridge radios hung on it.  The first radio is a Air Bridge Outdoor attached to a 24 dbi grid that is talking to a POP 3.5 miles away.  On the other side of the tower, I have a AirPointPro Outdoor attached to a 95 degree Sector Antenna pointing toward wireless clients.   The radios are connected to each other using a 4 port hub and one client computer is also connected to that same hub.   The network looks like this:   POPàABOàhubàAPPOàclients                      The problem is that right now all the clients are using a common IP Subnet as the ABO (10.6.0.12, 255.255.248.0, POP Gateway 10.6.0.1).  I have several devices behind the APPO and wondered if I could stick a Cisco 2514 (2 ethernet ports, first one being on the 10.6.0.0 network, and the second on the 192.168.1.0 network) between the ABO and the APPO and hand the clients DHCP IP addresses generated by the router in the 192.168.1.1 255.255.255.0 subnet   Technically will this work using my current equipment?   Thanks, Robin   --- Incoming mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.529 / Virus Database: 324 - Release Date: 10/16/2003 --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.529 / Virus Database: 324 - Release Date: 10/16/2003