A follow-up/reply;
I forgot to mention about wiping off the wire after each cut. I have
cut cores with and without doing this and can't be sure if it really
helps. Could be because I left a little foam on the blank ahead of the
actual LE (which I cut off afterwards) to help stabilize the wire temp.
Regarding Tom's reply, nearly everyone said to use stainless wire and
cut the bottom first. This is what I have done so I have not
experienced the result he describes.
Regarding Aerofoam's comment, I am doing what he describes. The
overburn is not a whole lot. However it is additive and between the
"cusping" and the "hairs" for two cuts, the error was the .020" I
relayed. This was noted on nearly 18-24 cores (ranging from 7" to 10"
chords and 24" lengths) before I finally tried the other way.
Lastly on Stan's reply, I find that the wider kerf on the slow side of
the core does not appear material unless the taper ratio is great. High
taper ratios like this are usually found on tip panels.
Remember, I repeated this experiment many times and tested each result
to the standard of a fresh printout of the airfoil. I have a high
degree of confidence in the results and will use the procedure described
religiously from now on.
Thank you for your replies. This kind of dialog makes the exchange the
great thing it is.
Tom Broeski wrote:
>
> People are always talking about wiping off the fuzz after cutting their cores. I
>use a very fine, high tension nichrome wire. I get zero fuze and no burnout. I also
>cut the top of my cores first. This lets the panel stay in position while I switch
>to the bottom templates. Since, the core is still attached, the alignment is very
>accurate. I get a perfectly feathered razor edge on my cores. I leave a 1/4" of
>glass on the wings after glassing for a very sharp trailing edge.
>
Aerofoam wrote:
> Over burning the cores should only be an issue when you are trying
> to cut as fast as you possibly can, I.E. production.
> For the guy that is just cutting his own cores it shouldn't be a problem.
> Just turn the heat down and cut slow.
> When I am cutting epp, I am cutting as fast as possible because
> I have a stack of cores that I want to finish. My drop bars have at least
> 3lbs of lead on them and I have the heat up high enough to produce
> a fair amount of smoke.(dont try this at home kids!)
> Styrene doesn't need nearly as much heat to cut fast.
> If you are getting a lot of overburn, you should do a combination or all of
> the steps below:
>
> A. Turn down the heat
> B. get a heavier weight.
> C. get better wire (SS or inconel) and make it very tight.
> D. use the smallest diameter wire that will hold the needed tension.
> I use .032 on bows over 3ft. and .022 to .024 on bows from 20"
> to 3ft. I use .014 on my small parallel bar cutig rig.
> E. dont use a power supply at the top of it's range, get one with some
> head room so it wont vary the current as the cut developes.
>
[EMAIL PROTECTED] wrote:
> Another problematic issue for CNC type cutters is overburn due to wire
> velocity. In order for the wire to enter/exit at the same time one end is
> moving slower in relationship to the other end (or faster the other way
> around). This translates into wider kerf at the "slow" end.
>
> With that said, I'm not real sure but that "gravity-powered" cutters have the
> same problem. I haven't made up my mind nor done any "scientific" studys.
>
> Comments are welcome so that I may settle this in my own mind!
--
Ron Richardson
mailto:[EMAIL PROTECTED]
Birmingham, AL, USA
RCSE-List facilities provided by Model Airplane News. Send "subscribe" and
"unsubscribe" requests to [EMAIL PROTECTED]